tender for safety relief valves of inlet and outlet size 15mm x 25 mm with set pressure 0.16 barg , safety relief valves of inlet and outlet size 80 mm x 100 mm with set pressure 4.5 barg , safety relief valves of inlet and outlet size 25 mm x 32 mm with set pressure 6 barg , safety relief valves of inlet and outlet size 25 mm x 50 mm with set pressure 16.5 barg , safety relief valves of inlet and outlet size 25 mm x 50 mm with set pressure 2.2 barg , safety relief valves of inlet and outlet size 50 mm x 50 mm with set pressure 2.2 barg , safety relief valves of inlet and outlet size 100 mm x 100 mm with set pressure 0.22 barg, safety relief valves, supply and safe delivery of safety relief valves of inlet and outlet size 15mm x 25 mm with set pressure 0.16 barg suitable for gas temperature service of 150 deg c as per drawing attached as annexure -1. the valve design shall conform to asme section viii div.1 and api 520 part i, with orifice area and center-to-face dimensions as per api 526. flanged end connections shall be as per asme b16.5 with specified ratings and raised face serrated finish as per drawing. materials of construction shall be as per drawing. each valve shall be factory set to the specified set pressure and tested. seat leakage test shall be as per api 527, shell test as per asme b16.34 and set pressure verification as per asme sec viii div.1. hydrostatic test pressure shall meet specified requirements as per drawing. dimensions and ratings shall match the drawing so as to fully interchangeable with existing installed srv. supply shall include approved ga drawing, valid material test certificates, pressure test reports, calibration certificate and complete compliance to drawing without deviation., supply and safe delivery of safety relief valves of inlet and outlet size 80 mm x 100 mm with set pressure 4.5 barg suitable for gas temperature service of 350 deg c as per drawing attached as annexure -2. the valve design shall conform to asme section viii div.1 and api 520 part i, with orifice area and center-to-face dimensions as per api 526. flanged end connections shall be as per asme b16.5 with specified ratings and raised face serrated finish as per drawing. materials of construction shall be as per drawing. each valve shall be factory set to the specified set pressure and tested. seat leakage test shall be as per api 527, shell test as per asme b16.34 and set pressure verification as per asme sec viii div.1. hydrostatic test pressure shall meet specified requirements as per drawing. dimensions and ratings shall match the drawing so as to fully interchangeable with existing installed srv. supply shall include approved ga drawing, valid material test certificates, pressure test reports, calibration certificate and complete compliance to drawing without deviation., supply and safe delivery of safety relief valves of inlet and outlet size 25 mm x 32 mm with set pressure 6 barg suitable for gas temperature service of 350 deg c as per drawing attached as annexure -3. the valve design shall conform to asme section viii div.1 and api 520 part i, with orifice area and center-to-face dimensions as per api 526. flanged end connections shall be as per asme b16.5 with specified ratings and raised face serrated finish as per drawing. materials of construction shall be as per drawing. each valve shall be factory set to the specified set pressure and tested. seat leakage test shall be as per api 527, shell test as per asme b16.34 and set pressure verification as per asme sec viii div.1. hydrostatic test pressure shall meet specified requirements as per drawing. dimensions and ratings shall match the drawing so as to fully interchangeable with existing installed srv. supply shall include approved ga drawing, valid material test certificates, pressure test reports, calibration certificate and complete compliance to drawing without deviation., supply and safe delivery of safety relief valves of inlet and outlet size 25 mm x 50 mm with set pressure 16.5 barg suitable for gas temperature service of ambient condition as per drawing attached as annexure -4. the valve design shall conform to asme section viii div.1 and api 520 part i, with orifice area and center-to-face dimensions as per api 526. flanged end connections shall be as per asme b16.5 with specified ratings and raised face serrated finish as per drawing. materials of construction shall be as per drawing. each valve shall be factory set to the specified set pressure and tested. seat leakage test shall be as per api 527, shell test as per asme b16.34 and set pressure verification as per asme sec viii div.1. hydrostatic test pressure shall meet specified requirements as per drawing. dimensions and ratings shall match the drawing so as to fully interchangeable with existing installed srv. supply shall include approved ga drawing, valid material test certificates, pressure test reports, calibration certificate and complete compliance to drawing without deviation., supply and safe delivery of safety relief valves of inlet and outlet size 25 mm x 50 mm with set pressure 2.2 barg suitable for gas temperature service of ambient condition as per drawing attached as annexure -5. the valve design shall conform to asme section viii div.1 and api 520 part i, with orifice area and center-to-face dimensions as per api 526. flanged end connections shall be as per asme b16.5 with specified ratings and raised face serrated finish as per drawing. materials of construction shall be as per drawing. each valve shall be factory set to the specified set pressure and tested. seat leakage test shall be as per api 527, shell test as per asme b16.34 and set pressure verification as per asme sec viii div.1. hydrostatic test pressure shall meet specified requirements as per drawing. dimensions and ratings shall match the drawing so as to fully interchangeable with existing installed srv. supply shall include approved ga drawing, valid material test certificates, pressure test reports, calibration certificate and complete compliance to drawing without deviation., supply and safe delivery of safety relief valves of inlet and outlet size 50 mm x 50 mm with set pressure 2.2 barg suitable for gas temperature service of 450 deg c as per drawing attached as annexure -6. the valve design shall conform to asme section viii div.1 and api 520 part i, with orifice area and center-to-face dimensions as per api 526. flanged end connections shall be as per asme b16.5 with specified ratings and raised face serrated finish as per drawing. materials of construction shall be as per drawing. each valve shall be factory set to the specified set pressure and tested. seat leakage test shall be as per api 527, shell test as per asme b16.34 and set pressure verification as per asme sec viii div.1. hydrostatic test pressure shall meet specified requirements as per drawing. dimensions and ratings shall match the drawing so as to fully interchangeable with existing installed srv. supply shall include approved ga drawing, valid material test certificates, pressure test reports, calibration certificate and complete compliance to drawing without deviation., supply and safe delivery of safety relief valves of inlet and outlet size 100 mm x 100 mm with set pressure 0.22 barg suitable for gas temperature service of ambient condition as per drawing attached as annexure -7. the valve design shall conform to asme section viii div.1 and api 520 part i, with orifice area and center-to-face dimensions as per api 526. flanged end connections shall be as per asme b16.5 with specified ratings and raised face serrated finish as per drawing. materials of construction shall be as per drawing. each valve shall be factory set to the specified set pressure and tested. seat leakage test shall be as per api 527, shell test as per asme b16.34 and set pressure verification as per asme sec viii div.1. hydrostatic test pressure shall meet specified requirements as per drawing. dimensions and ratings shall match the drawing so as to fully interchangeable with existing installed srv. supply shall include approved ga drawing, valid material test certificates, pressure test reports, calibration certificate and complete compliance to drawing without deviation.

You can fill out the integrated inquiry form below on this detail page to share your company profile. Our consultancy desk will review your query regarding parameters and guide you on how to coordinate efficiently with the procurement team of Bharatiya Nabhikiya Vidyut Nigam Limited BHAVINI

Tender18 provides end-to-end professional bidding support and documentation advisory for Tender For Safety Relief Valves Of Inlet And Outlet Size 15mm X 25 Mm With Set Pressure 0.16 Barg , Safety Relief Valves Of Inlet And Outlet Size 80 Mm X 100 Mm With Set Pressure 4.5 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 32 Mm With Set Pressure 6 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 16.5 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 2.2 Barg , Safety Relief Valves Of Inlet And Outlet Size 50 Mm X 50 Mm With Set Pressure 2.2 Barg , Safety Relief Valves Of Inlet And Outlet Size 100 Mm X 100 Mm With Set Pressure 0.22 Barg, Safety Relief Valves, Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 15mm X 25 Mm With Set Pressure 0.16 Barg Suitable For Gas Temperature Service Of 150 Deg C As Per Drawing Attached As Annexure -1. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 80 Mm X 100 Mm With Set Pressure 4.5 Barg Suitable For Gas Temperature Service Of 350 Deg C As Per Drawing Attached As Annexure -2. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 32 Mm With Set Pressure 6 Barg Suitable For Gas Temperature Service Of 350 Deg C As Per Drawing Attached As Annexure -3. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 16.5 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -4. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 2.2 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -5. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 50 Mm X 50 Mm With Set Pressure 2.2 Barg Suitable For Gas Temperature Service Of 450 Deg C As Per Drawing Attached As Annexure -6. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 100 Mm X 100 Mm With Set Pressure 0.22 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -7. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation. . Our senior analysts help you decode the complete project guidelines, manage accurate costing sheets, and complete error-free submissions on the official platform used by Bharatiya Nabhikiya Vidyut Nigam Limited BHAVINI.

Most online bids face rejection during the initial evaluation round due to avoidable errors like uploading blurred document scans, submitting expired DSCs, or missing critical experience papers required for Tender For Safety Relief Valves Of Inlet And Outlet Size 15mm X 25 Mm With Set Pressure 0.16 Barg , Safety Relief Valves Of Inlet And Outlet Size 80 Mm X 100 Mm With Set Pressure 4.5 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 32 Mm With Set Pressure 6 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 16.5 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 2.2 Barg , Safety Relief Valves Of Inlet And Outlet Size 50 Mm X 50 Mm With Set Pressure 2.2 Barg , Safety Relief Valves Of Inlet And Outlet Size 100 Mm X 100 Mm With Set Pressure 0.22 Barg, Safety Relief Valves, Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 15mm X 25 Mm With Set Pressure 0.16 Barg Suitable For Gas Temperature Service Of 150 Deg C As Per Drawing Attached As Annexure -1. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 80 Mm X 100 Mm With Set Pressure 4.5 Barg Suitable For Gas Temperature Service Of 350 Deg C As Per Drawing Attached As Annexure -2. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 32 Mm With Set Pressure 6 Barg Suitable For Gas Temperature Service Of 350 Deg C As Per Drawing Attached As Annexure -3. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 16.5 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -4. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 2.2 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -5. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 50 Mm X 50 Mm With Set Pressure 2.2 Barg Suitable For Gas Temperature Service Of 450 Deg C As Per Drawing Attached As Annexure -6. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 100 Mm X 100 Mm With Set Pressure 0.22 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -7. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation. in Tamil Nadu.

Eligibility for outstation bidders depends entirely on the terms set inside the document for Tender For Safety Relief Valves Of Inlet And Outlet Size 15mm X 25 Mm With Set Pressure 0.16 Barg , Safety Relief Valves Of Inlet And Outlet Size 80 Mm X 100 Mm With Set Pressure 4.5 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 32 Mm With Set Pressure 6 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 16.5 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 2.2 Barg , Safety Relief Valves Of Inlet And Outlet Size 50 Mm X 50 Mm With Set Pressure 2.2 Barg , Safety Relief Valves Of Inlet And Outlet Size 100 Mm X 100 Mm With Set Pressure 0.22 Barg, Safety Relief Valves, Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 15mm X 25 Mm With Set Pressure 0.16 Barg Suitable For Gas Temperature Service Of 150 Deg C As Per Drawing Attached As Annexure -1. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 80 Mm X 100 Mm With Set Pressure 4.5 Barg Suitable For Gas Temperature Service Of 350 Deg C As Per Drawing Attached As Annexure -2. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 32 Mm With Set Pressure 6 Barg Suitable For Gas Temperature Service Of 350 Deg C As Per Drawing Attached As Annexure -3. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 16.5 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -4. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 2.2 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -5. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 50 Mm X 50 Mm With Set Pressure 2.2 Barg Suitable For Gas Temperature Service Of 450 Deg C As Per Drawing Attached As Annexure -6. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 100 Mm X 100 Mm With Set Pressure 0.22 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -7. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation.. While many public sector projects allow national competitive bidding, certain localized works require local offices or specific registration metrics in Tiruklalikundram.

If this procurement is routed through the central marketplace, an active GeM Seller ID is mandatory to supply items. Tender18 offers complete assistance for brand cataloging, profile creation, and vendor assessment required officially by Bharatiya Nabhikiya Vidyut Nigam Limited BHAVINI

To register an eligible bid for these contracts, companies must prepare their core compliance documents. Vendors operating across Tamil Nadu must ensure they possess a valid GST registration, permanent account number (PAN), and active Class-3 Digital Signature Certificates.

This public procurement cycle is specifically looking for qualified vendors and suppliers who can provide high-quality solutions. The operational execution, delivery, and deployment of these materials must be managed locally within the Tiruklalikundram region.

The estimated project cost and budget thresholds can be reviewed directly inside the tender document. Bidders can analyze these qualification files to check if their firm meets the financial capability criteria specified for Tender For Safety Relief Valves Of Inlet And Outlet Size 15mm X 25 Mm With Set Pressure 0.16 Barg , Safety Relief Valves Of Inlet And Outlet Size 80 Mm X 100 Mm With Set Pressure 4.5 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 32 Mm With Set Pressure 6 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 16.5 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 2.2 Barg , Safety Relief Valves Of Inlet And Outlet Size 50 Mm X 50 Mm With Set Pressure 2.2 Barg , Safety Relief Valves Of Inlet And Outlet Size 100 Mm X 100 Mm With Set Pressure 0.22 Barg, Safety Relief Valves, Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 15mm X 25 Mm With Set Pressure 0.16 Barg Suitable For Gas Temperature Service Of 150 Deg C As Per Drawing Attached As Annexure -1. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 80 Mm X 100 Mm With Set Pressure 4.5 Barg Suitable For Gas Temperature Service Of 350 Deg C As Per Drawing Attached As Annexure -2. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 32 Mm With Set Pressure 6 Barg Suitable For Gas Temperature Service Of 350 Deg C As Per Drawing Attached As Annexure -3. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 16.5 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -4. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 2.2 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -5. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 50 Mm X 50 Mm With Set Pressure 2.2 Barg Suitable For Gas Temperature Service Of 450 Deg C As Per Drawing Attached As Annexure -6. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 100 Mm X 100 Mm With Set Pressure 0.22 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -7. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation. by Bharatiya Nabhikiya Vidyut Nigam Limited BHAVINI

You can download the commercial Bill of Quantities (BOQ) spreadsheet directly using the secure link provided on this page. The BOQ file contains the item descriptions and rate filling forms officially validated for Tender For Safety Relief Valves Of Inlet And Outlet Size 15mm X 25 Mm With Set Pressure 0.16 Barg , Safety Relief Valves Of Inlet And Outlet Size 80 Mm X 100 Mm With Set Pressure 4.5 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 32 Mm With Set Pressure 6 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 16.5 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 2.2 Barg , Safety Relief Valves Of Inlet And Outlet Size 50 Mm X 50 Mm With Set Pressure 2.2 Barg , Safety Relief Valves Of Inlet And Outlet Size 100 Mm X 100 Mm With Set Pressure 0.22 Barg, Safety Relief Valves, Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 15mm X 25 Mm With Set Pressure 0.16 Barg Suitable For Gas Temperature Service Of 150 Deg C As Per Drawing Attached As Annexure -1. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 80 Mm X 100 Mm With Set Pressure 4.5 Barg Suitable For Gas Temperature Service Of 350 Deg C As Per Drawing Attached As Annexure -2. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 32 Mm With Set Pressure 6 Barg Suitable For Gas Temperature Service Of 350 Deg C As Per Drawing Attached As Annexure -3. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 16.5 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -4. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 2.2 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -5. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 50 Mm X 50 Mm With Set Pressure 2.2 Barg Suitable For Gas Temperature Service Of 450 Deg C As Per Drawing Attached As Annexure -6. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 100 Mm X 100 Mm With Set Pressure 0.22 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -7. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation. within the Tamil Nadu jurisdiction

The official timeline and deadline details for Tender For Safety Relief Valves Of Inlet And Outlet Size 15mm X 25 Mm With Set Pressure 0.16 Barg , Safety Relief Valves Of Inlet And Outlet Size 80 Mm X 100 Mm With Set Pressure 4.5 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 32 Mm With Set Pressure 6 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 16.5 Barg , Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 2.2 Barg , Safety Relief Valves Of Inlet And Outlet Size 50 Mm X 50 Mm With Set Pressure 2.2 Barg , Safety Relief Valves Of Inlet And Outlet Size 100 Mm X 100 Mm With Set Pressure 0.22 Barg, Safety Relief Valves, Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 15mm X 25 Mm With Set Pressure 0.16 Barg Suitable For Gas Temperature Service Of 150 Deg C As Per Drawing Attached As Annexure -1. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 80 Mm X 100 Mm With Set Pressure 4.5 Barg Suitable For Gas Temperature Service Of 350 Deg C As Per Drawing Attached As Annexure -2. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 32 Mm With Set Pressure 6 Barg Suitable For Gas Temperature Service Of 350 Deg C As Per Drawing Attached As Annexure -3. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 16.5 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -4. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 25 Mm X 50 Mm With Set Pressure 2.2 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -5. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 50 Mm X 50 Mm With Set Pressure 2.2 Barg Suitable For Gas Temperature Service Of 450 Deg C As Per Drawing Attached As Annexure -6. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation., Supply And Safe Delivery Of Safety Relief Valves Of Inlet And Outlet Size 100 Mm X 100 Mm With Set Pressure 0.22 Barg Suitable For Gas Temperature Service Of Ambient Condition As Per Drawing Attached As Annexure -7. The Valve Design Shall Conform To Asme Section Viii Div.1 And Api 520 Part I, With Orifice Area And Center-to-face Dimensions As Per Api 526. Flanged End Connections Shall Be As Per Asme B16.5 With Specified Ratings And Raised Face Serrated Finish As Per Drawing. Materials Of Construction Shall Be As Per Drawing. Each Valve Shall Be Factory Set To The Specified Set Pressure And Tested. Seat Leakage Test Shall Be As Per Api 527, Shell Test As Per Asme B16.34 And Set Pressure Verification As Per Asme Sec Viii Div.1. Hydrostatic Test Pressure Shall Meet Specified Requirements As Per Drawing. Dimensions And Ratings Shall Match The Drawing So As To Fully Interchangeable With Existing Installed Srv. Supply Shall Include Approved Ga Drawing, Valid Material Test Certificates, Pressure Test Reports, Calibration Certificate And Complete Compliance To Drawing Without Deviation. are available inside the detailed notification files. Bidders planning to target this contract in Tiruklalikundram should check the official portal schedule early to complete their online technical and financial submission well before the closing hours.