tender for revolving chair (v5) (q2) , steel filing cabinets for general office purpose (v2) as per is 3313 (q2) , chair for general purpose (q2) , chair writing with cushion , table office clerk fd 1004 , almirah medium steel with shelves fd 1032 , sofa set 5 seater fd 281 , table centre fd 375 , book case steel fd 1028 , desk stand lecture fd 1028 , table computer fd e6 map 03 , rack pigeon holes steel fd 1037 , table plotting executive tp , controller desk tp , sofa set 3 seater fd 281 , board notice fd 99 m, tp fur for atc building bihta, chair writing with cushion dimension the overall size of the chair shall approx be 950mm high 500mmwide description it shall be of trade pattern and of one make and model as described.the size dimensions of the chair shall meet the overall specification as described.the frame of the chair shall be of ms tubular frame powder coated cantilever type of size 25mmx10mm in section. back form shall be designed with contoured lumber support for extra comfort.120mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam with pvc lipping alround shall be provided at seat and back.arm rest shall be of black integral skin poly urethane with shore a hardness and reinforced with ms insert. it shall be scratch and wheather resistant.both hand rest section shall have inner and outer dia of 210mm and 230mm respectively and have slope towards front. finish pre treated with epoxy powder caoted oven baked with ivory white colour white warmgrey., table office clk table office clerk steel fd 1004 overall size shall be 1200mm long, 610mm wide and 760mm high. steel frame shall be of size 1160x570x742mm .four legs of 25mm mild steel tube of 1.6mm wall thickness shall be provided. top of legs shall be joined together with 25mm square mild steel tube of wall thickness 1.6mm in long and short sides. two short stiffeners f same size shall be provided at 130mm from bottom of legs. one long stiffener shall also be provided to the middle of short stiffeners. three drawers of equal size shall be provided on the right hand side above the stiffener at 130mm high with overall size of 350mm wide and 430mm high and 410mm deep. the top of table shall be provided with pre-laminated particle board of 18 19mm thick with teak veener shade and pvc edging alround the table .hard rubber pvc toes shall be provided to the legs. locking device shall be provided to drawers. all steel surfaces exposed to view shall be given two coats ofwhite or silver grey or as aaproved by ge enamel paint over a coat of primer with spray machine after preparation of steel surfaces. rest all as per drgs., almirah medium steel with shelves dimension overall size shall be 1270mm high,765mm wide and 440mm deep. description the base shall be made of two numbers mild steel sheet channel base welded to bottom of almirah and shall be 100mm high. mild steel sheet shall be 1mm thick for channel base. the base channel shall be welded at 50mm from each end of 765mm length and shall be up to full width of 440mm of almirah. top sides back bottom and front of almirah shall be of 1mm thick mild steel sheet. three shelves equally spaced making four compartments shall be provided and shall be of 1mm thick mild steel sheet.front shutters shall have two leaves.all joints and welding fixing shall be done according standard workmanship handle a steel chromium plated handle 100mm long shall be provided to the shutter. locking device the locking device shall be three way locking device and shall also be provided with decorative key plate .make of lock harrison godrej. finish all steel surfaces exposed to view when placed in position shall be painted in dual colur over a coat of primer with spray machine after preparation of surfaces. a mark of mes shall also be provided on left top corner of front shutter of visisble colour as directed by engr in charge.rest all as per drgs, sofa set 5 seater dimension overall size of one seat shall be 670mm long and 745 mm wide and 530mm high up to arm rest level. description the sofa set 2 seater shall consist of two single seats. all wood shall be of first class teak wood mp.legs of sofa set shall be 70mm x35mm in section teak wood . front legs shall be jointed by 100mm x 35mm in section wooden rail in front . front and rear legs shall be joined with 100mm x 35mm in section wooden rails in sides. 100mm thick seat cushion and back cushions shall be of size 530mm x 560mm one numbers in seat and one numbers in the back. the cushion shall be of cool foam or any other superior quality foam of 40 density as approved by engineer in charge. cushion shall be covered with approved color tapestry cloth approved by ge not less than rs 300 meter or as directed byengineer in charge. finish all wood surface exposed to view when placed in position shall be french polished with lacquer finish rest.rest all as per drg. dimension overall size of the three seat shall be 1730mm long 745mm wide and 530mm high. description the set consist of one long piece of three seat only. well seasoned teak wood throughout in frame work shall be used for manufacturing of sofa.ll wood shall be of first class teak wood mp legs of sofa set shall be 70mm x35mm in section teak wood . front legs shall be jointed by 100mm x 35mm in section wooden rail in front .front and rear legs shall be joined with 100mm x 35mm in section wooden rails in sides.100mm thick cushion of 40 density covered with best quality tapestry cloth approved by ge not less than rs 300 meter shall be provided at seat and back as directed by engr in charge. make of cushion kurlon sleepwell nindiya. finish all wooden surfaces internally and externally shall be melamine polished with high lacquer finish of walnut shade after properly smoothened the surface with sand emery paper. rest all specifications are as per drg., table centre dimension overall size shall be 900mm long, 450mm wide and 400mm high. description all wood shall be of teak wood. top of the table shall be of 18mm thick prelaminated mdf board of approved shade with 4mm thick teak wood beading all-round the edges of top.legs shall be made out of 60mmx30mm in section teak wood and 356 mm high. bottom rail of teak wood of 20mmx50mm in section and 420mm long shall be provided between legs, widthwise at 100mm above the bottom of legs.the bottom tier shall be fixed on the top of bottom side rails with 50mm long screwss.the bottom tier shall be of 18mm thick prelaminated particle board exterior grade of approved shade with 4mm thick teak wood beading all-round the edges of both the tops.25mm dia hard rubber pvc rings shall be fixed to the bottom of all legs fixed with 30mm long screws. finish all wood surfaces shall be french polished with high gloss finish rest all as per drg., book case steel dimension over all size shall be of 840 mm long 310 mm wide and 1675 mm high . description all sheet shall be mild steel sheet 1 mm thick back sides bottom top and shelves.the book case shall be provided with four compartments of equal size. the shutters of each compartment shall open towards top and slide into the depth of the book case.transparent glass 4mm thick shall be provided to front shutters. two steel handles of 100 mm long shall be provided to each shutter of the compartment. the locking device shall be provided to each compartment with duplicate key and each shutter shall be provided with decorative key plate .make of lock godrej harrison link finish all steel surfaces exposed to view when placed in position shall be painted in dual colur over a coat of primer with spray machine after preparation of surfaces. a mark of mes shall also be provided on left top corner of front shutter of visisble colour as directed by engr in charge.rest all as per drgs, desk stand lecture dimension over all size shall be 970mm wide and 1220mm high. description two upright of mild steel rectangular tube of 75mmx25mm of 1202mm high shall be provided in rear side and shall be 635mm apart. the two upright shall be joinded with bottom, middle and top rails with 75mmx50mm mild steel tube of wal thickness 1.6mm. the two sides rails at bottom fixed at 125mm from bottom shall be 430mm long 75mmx50mm mild steel tube of wall thickness 1.6mm and shall form the part of bottom rails and join the long side of bottom rail of size 785mm long, . all edges of pre-laminated particle board remained exposed shall be covered with teak wood edging as per the size of board edging. finish all steel surfaces exposed to view when placed in position shall be given two coats of enamel paint over a coat of primer with spray machine after preparation of steel surfaces and all wooden surfaces shall be melamine polish with lacquer finish as approved by engr in charge.rest all as per drgs, table computer dimension overall size of top shall be 900mm long 561.20 mm wide and 750mm high. description all prelaminated particle board used in manufacturing of top shelves drawers tray shall be of 18mm thick prelaminated mdf board. the frame of table shall be of 25mm square pipe of wall thickness not lss than 1.6mm. the top of table shall be provided with 4mm thick teak wood beading.the legs shall be made out of 25mmx50mm ms rectangular cr pipe of 18 guage.each leg shall be provided with rectangular pvc cover made to shape on front sides only. the drawers shall be provided with telescopic channel 300mm long.the legs shall also be provided with nylon buffers .rest all as per drg. finish all wood surfaces shall be french polished with high gloss finish rest all as per drg., rack pigeon holes steel dimension over all size shall be of 1905x610x915mm. description the entire rack shall be made of 1mm mild steel sheet.the sides shall be provided with 40x40x4mm angle iron welded to 1.00mm thick ms sheet.75x75x3mm thick flat iron cut to shape shall be welded at front corner.all partitions shall also be made of 1mm thick mild steel sheet and welded to each other in continous. all dimensions, shape and size shall be followed as per drg. all joints, fixing shallbe done in accordance with standard specifications. rest all as shown on drg. finish all steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces. a mark of mes shall also be provided on top left side with visible colour. painting shall be done with spray machine.rest all as per drg., table plotting executive size 1500x750x750mm, controller desk, sofa set 3 seater dimension overall size of the three seat shall be 1730mm long 745mm wide and 530mm high. description the set consist of one long piece of three seat only.well seasoned teak wood throughout in frame work shall be used for manufacturing of sofa.all wood shall be of first class teak wood mp legs of sofa set shall be 70mm x35mm in section teak wood . front legs shall be jointed by 100mm x 35mm in section wooden rail in front .front and rear legs shall be joined with 100mm x 35mm in section wooden rails in sides.100mm thick cushion of 40 density covered with best quality tapestry cloth approved by ge not less than rs 300 meter shall be provided at seat and back as directed by engr in charge. make of cushion kurlon sleepwell nindiya. finish all wooden surfaces internally and externally shall be melamine polished with high lacquer finish of walnut shade after properly smoothened the surface with sand emery paper.rest all specifications are as per drg., board notice 2400x1220mm all details as per drg.

You can fill out the integrated inquiry form below on this detail page to share your company profile. Our consultancy desk will review your query regarding parameters and guide you on how to coordinate efficiently with the procurement team of Indian Army

Tender18 provides end-to-end professional bidding support and documentation advisory for Tender For Revolving Chair (v5) (q2) , Steel Filing Cabinets For General Office Purpose (v2) As Per Is 3313 (q2) , Chair For General Purpose (q2) , Chair Writing With Cushion , Table Office Clerk Fd 1004 , Almirah Medium Steel With Shelves Fd 1032 , Sofa Set 5 Seater Fd 281 , Table Centre Fd 375 , Book Case Steel Fd 1028 , Desk Stand Lecture Fd 1028 , Table Computer Fd E6 Map 03 , Rack Pigeon Holes Steel Fd 1037 , Table Plotting Executive Tp , Controller Desk Tp , Sofa Set 3 Seater Fd 281 , Board Notice Fd 99 M, Tp Fur For Atc Building Bihta, Chair Writing With Cushion Dimension The Overall Size Of The Chair Shall Approx Be 950mm High 500mmwide Description It Shall Be Of Trade Pattern And Of One Make And Model As Described.the Size Dimensions Of The Chair Shall Meet The Overall Specification As Described.the Frame Of The Chair Shall Be Of Ms Tubular Frame Powder Coated Cantilever Type Of Size 25mmx10mm In Section. Back Form Shall Be Designed With Contoured Lumber Support For Extra Comfort.120mm Thick Hot Pressed Plywood Upholstered With Fabric And Moulded Polyurethane Foam With Pvc Lipping Alround Shall Be Provided At Seat And Back.arm Rest Shall Be Of Black Integral Skin Poly Urethane With Shore A Hardness And Reinforced With Ms Insert. It Shall Be Scratch And Wheather Resistant.both Hand Rest Section Shall Have Inner And Outer Dia Of 210mm And 230mm Respectively And Have Slope Towards Front. Finish Pre Treated With Epoxy Powder Caoted Oven Baked With Ivory White Colour White Warmgrey., Table Office Clk Table Office Clerk Steel Fd 1004 Overall Size Shall Be 1200mm Long, 610mm Wide And 760mm High. Steel Frame Shall Be Of Size 1160x570x742mm .four Legs Of 25mm Mild Steel Tube Of 1.6mm Wall Thickness Shall Be Provided. Top Of Legs Shall Be Joined Together With 25mm Square Mild Steel Tube Of Wall Thickness 1.6mm In Long And Short Sides. Two Short Stiffeners F Same Size Shall Be Provided At 130mm From Bottom Of Legs. One Long Stiffener Shall Also Be Provided To The Middle Of Short Stiffeners. Three Drawers Of Equal Size Shall Be Provided On The Right Hand Side Above The Stiffener At 130mm High With Overall Size Of 350mm Wide And 430mm High And 410mm Deep. The Top Of Table Shall Be Provided With Pre-laminated Particle Board Of 18 19mm Thick With Teak Veener Shade And Pvc Edging Alround The Table .hard Rubber Pvc Toes Shall Be Provided To The Legs. Locking Device Shall Be Provided To Drawers. All Steel Surfaces Exposed To View Shall Be Given Two Coats Ofwhite Or Silver Grey Or As Aaproved By Ge Enamel Paint Over A Coat Of Primer With Spray Machine After Preparation Of Steel Surfaces. Rest All As Per Drgs., Almirah Medium Steel With Shelves Dimension Overall Size Shall Be 1270mm High,765mm Wide And 440mm Deep. Description The Base Shall Be Made Of Two Numbers Mild Steel Sheet Channel Base Welded To Bottom Of Almirah And Shall Be 100mm High. Mild Steel Sheet Shall Be 1mm Thick For Channel Base. The Base Channel Shall Be Welded At 50mm From Each End Of 765mm Length And Shall Be Up To Full Width Of 440mm Of Almirah. Top Sides Back Bottom And Front Of Almirah Shall Be Of 1mm Thick Mild Steel Sheet. Three Shelves Equally Spaced Making Four Compartments Shall Be Provided And Shall Be Of 1mm Thick Mild Steel Sheet.front Shutters Shall Have Two Leaves.all Joints And Welding Fixing Shall Be Done According Standard Workmanship Handle A Steel Chromium Plated Handle 100mm Long Shall Be Provided To The Shutter. Locking Device The Locking Device Shall Be Three Way Locking Device And Shall Also Be Provided With Decorative Key Plate .make Of Lock Harrison Godrej. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted In Dual Colur Over A Coat Of Primer With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Left Top Corner Of Front Shutter Of Visisble Colour As Directed By Engr In Charge.rest All As Per Drgs, Sofa Set 5 Seater Dimension Overall Size Of One Seat Shall Be 670mm Long And 745 Mm Wide And 530mm High Up To Arm Rest Level. Description The Sofa Set 2 Seater Shall Consist Of Two Single Seats. All Wood Shall Be Of First Class Teak Wood Mp.legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front . Front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides. 100mm Thick Seat Cushion And Back Cushions Shall Be Of Size 530mm X 560mm One Numbers In Seat And One Numbers In The Back. The Cushion Shall Be Of Cool Foam Or Any Other Superior Quality Foam Of 40 Density As Approved By Engineer In Charge. Cushion Shall Be Covered With Approved Color Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Or As Directed Byengineer In Charge. Finish All Wood Surface Exposed To View When Placed In Position Shall Be French Polished With Lacquer Finish Rest.rest All As Per Drg. Dimension Overall Size Of The Three Seat Shall Be 1730mm Long 745mm Wide And 530mm High. Description The Set Consist Of One Long Piece Of Three Seat Only. Well Seasoned Teak Wood Throughout In Frame Work Shall Be Used For Manufacturing Of Sofa.ll Wood Shall Be Of First Class Teak Wood Mp Legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front .front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides.100mm Thick Cushion Of 40 Density Covered With Best Quality Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Shall Be Provided At Seat And Back As Directed By Engr In Charge. Make Of Cushion Kurlon Sleepwell Nindiya. Finish All Wooden Surfaces Internally And Externally Shall Be Melamine Polished With High Lacquer Finish Of Walnut Shade After Properly Smoothened The Surface With Sand Emery Paper. Rest All Specifications Are As Per Drg., Table Centre Dimension Overall Size Shall Be 900mm Long, 450mm Wide And 400mm High. Description All Wood Shall Be Of Teak Wood. Top Of The Table Shall Be Of 18mm Thick Prelaminated Mdf Board Of Approved Shade With 4mm Thick Teak Wood Beading All-round The Edges Of Top.legs Shall Be Made Out Of 60mmx30mm In Section Teak Wood And 356 Mm High. Bottom Rail Of Teak Wood Of 20mmx50mm In Section And 420mm Long Shall Be Provided Between Legs, Widthwise At 100mm Above The Bottom Of Legs.the Bottom Tier Shall Be Fixed On The Top Of Bottom Side Rails With 50mm Long Screwss.the Bottom Tier Shall Be Of 18mm Thick Prelaminated Particle Board Exterior Grade Of Approved Shade With 4mm Thick Teak Wood Beading All-round The Edges Of Both The Tops.25mm Dia Hard Rubber Pvc Rings Shall Be Fixed To The Bottom Of All Legs Fixed With 30mm Long Screws. Finish All Wood Surfaces Shall Be French Polished With High Gloss Finish Rest All As Per Drg., Book Case Steel Dimension Over All Size Shall Be Of 840 Mm Long 310 Mm Wide And 1675 Mm High . Description All Sheet Shall Be Mild Steel Sheet 1 Mm Thick Back Sides Bottom Top And Shelves.the Book Case Shall Be Provided With Four Compartments Of Equal Size. The Shutters Of Each Compartment Shall Open Towards Top And Slide Into The Depth Of The Book Case.transparent Glass 4mm Thick Shall Be Provided To Front Shutters. Two Steel Handles Of 100 Mm Long Shall Be Provided To Each Shutter Of The Compartment. The Locking Device Shall Be Provided To Each Compartment With Duplicate Key And Each Shutter Shall Be Provided With Decorative Key Plate .make Of Lock Godrej Harrison Link Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted In Dual Colur Over A Coat Of Primer With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Left Top Corner Of Front Shutter Of Visisble Colour As Directed By Engr In Charge.rest All As Per Drgs, Desk Stand Lecture Dimension Over All Size Shall Be 970mm Wide And 1220mm High. Description Two Upright Of Mild Steel Rectangular Tube Of 75mmx25mm Of 1202mm High Shall Be Provided In Rear Side And Shall Be 635mm Apart. The Two Upright Shall Be Joinded With Bottom, Middle And Top Rails With 75mmx50mm Mild Steel Tube Of Wal Thickness 1.6mm. The Two Sides Rails At Bottom Fixed At 125mm From Bottom Shall Be 430mm Long 75mmx50mm Mild Steel Tube Of Wall Thickness 1.6mm And Shall Form The Part Of Bottom Rails And Join The Long Side Of Bottom Rail Of Size 785mm Long, . All Edges Of Pre-laminated Particle Board Remained Exposed Shall Be Covered With Teak Wood Edging As Per The Size Of Board Edging. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Given Two Coats Of Enamel Paint Over A Coat Of Primer With Spray Machine After Preparation Of Steel Surfaces And All Wooden Surfaces Shall Be Melamine Polish With Lacquer Finish As Approved By Engr In Charge.rest All As Per Drgs, Table Computer Dimension Overall Size Of Top Shall Be 900mm Long 561.20 Mm Wide And 750mm High. Description All Prelaminated Particle Board Used In Manufacturing Of Top Shelves Drawers Tray Shall Be Of 18mm Thick Prelaminated Mdf Board. The Frame Of Table Shall Be Of 25mm Square Pipe Of Wall Thickness Not Lss Than 1.6mm. The Top Of Table Shall Be Provided With 4mm Thick Teak Wood Beading.the Legs Shall Be Made Out Of 25mmx50mm Ms Rectangular Cr Pipe Of 18 Guage.each Leg Shall Be Provided With Rectangular Pvc Cover Made To Shape On Front Sides Only. The Drawers Shall Be Provided With Telescopic Channel 300mm Long.the Legs Shall Also Be Provided With Nylon Buffers .rest All As Per Drg. Finish All Wood Surfaces Shall Be French Polished With High Gloss Finish Rest All As Per Drg., Rack Pigeon Holes Steel Dimension Over All Size Shall Be Of 1905x610x915mm. Description The Entire Rack Shall Be Made Of 1mm Mild Steel Sheet.the Sides Shall Be Provided With 40x40x4mm Angle Iron Welded To 1.00mm Thick Ms Sheet.75x75x3mm Thick Flat Iron Cut To Shape Shall Be Welded At Front Corner.all Partitions Shall Also Be Made Of 1mm Thick Mild Steel Sheet And Welded To Each Other In Continous. All Dimensions, Shape And Size Shall Be Followed As Per Drg. All Joints, Fixing Shallbe Done In Accordance With Standard Specifications. Rest All As Shown On Drg. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted With Two Coats Of Silver Grey Hammer Paint Internally And Extrenally With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Top Left Side With Visible Colour. Painting Shall Be Done With Spray Machine.rest All As Per Drg., Table Plotting Executive Size 1500x750x750mm, Controller Desk, Sofa Set 3 Seater Dimension Overall Size Of The Three Seat Shall Be 1730mm Long 745mm Wide And 530mm High. Description The Set Consist Of One Long Piece Of Three Seat Only.well Seasoned Teak Wood Throughout In Frame Work Shall Be Used For Manufacturing Of Sofa.all Wood Shall Be Of First Class Teak Wood Mp Legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front .front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides.100mm Thick Cushion Of 40 Density Covered With Best Quality Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Shall Be Provided At Seat And Back As Directed By Engr In Charge. Make Of Cushion Kurlon Sleepwell Nindiya. Finish All Wooden Surfaces Internally And Externally Shall Be Melamine Polished With High Lacquer Finish Of Walnut Shade After Properly Smoothened The Surface With Sand Emery Paper.rest All Specifications Are As Per Drg., Board Notice 2400x1220mm All Details As Per Drg. . Our senior analysts help you decode the complete project guidelines, manage accurate costing sheets, and complete error-free submissions on the official platform used by Indian Army.

Most online bids face rejection during the initial evaluation round due to avoidable errors like uploading blurred document scans, submitting expired DSCs, or missing critical experience papers required for Tender For Revolving Chair (v5) (q2) , Steel Filing Cabinets For General Office Purpose (v2) As Per Is 3313 (q2) , Chair For General Purpose (q2) , Chair Writing With Cushion , Table Office Clerk Fd 1004 , Almirah Medium Steel With Shelves Fd 1032 , Sofa Set 5 Seater Fd 281 , Table Centre Fd 375 , Book Case Steel Fd 1028 , Desk Stand Lecture Fd 1028 , Table Computer Fd E6 Map 03 , Rack Pigeon Holes Steel Fd 1037 , Table Plotting Executive Tp , Controller Desk Tp , Sofa Set 3 Seater Fd 281 , Board Notice Fd 99 M, Tp Fur For Atc Building Bihta, Chair Writing With Cushion Dimension The Overall Size Of The Chair Shall Approx Be 950mm High 500mmwide Description It Shall Be Of Trade Pattern And Of One Make And Model As Described.the Size Dimensions Of The Chair Shall Meet The Overall Specification As Described.the Frame Of The Chair Shall Be Of Ms Tubular Frame Powder Coated Cantilever Type Of Size 25mmx10mm In Section. Back Form Shall Be Designed With Contoured Lumber Support For Extra Comfort.120mm Thick Hot Pressed Plywood Upholstered With Fabric And Moulded Polyurethane Foam With Pvc Lipping Alround Shall Be Provided At Seat And Back.arm Rest Shall Be Of Black Integral Skin Poly Urethane With Shore A Hardness And Reinforced With Ms Insert. It Shall Be Scratch And Wheather Resistant.both Hand Rest Section Shall Have Inner And Outer Dia Of 210mm And 230mm Respectively And Have Slope Towards Front. Finish Pre Treated With Epoxy Powder Caoted Oven Baked With Ivory White Colour White Warmgrey., Table Office Clk Table Office Clerk Steel Fd 1004 Overall Size Shall Be 1200mm Long, 610mm Wide And 760mm High. Steel Frame Shall Be Of Size 1160x570x742mm .four Legs Of 25mm Mild Steel Tube Of 1.6mm Wall Thickness Shall Be Provided. Top Of Legs Shall Be Joined Together With 25mm Square Mild Steel Tube Of Wall Thickness 1.6mm In Long And Short Sides. Two Short Stiffeners F Same Size Shall Be Provided At 130mm From Bottom Of Legs. One Long Stiffener Shall Also Be Provided To The Middle Of Short Stiffeners. Three Drawers Of Equal Size Shall Be Provided On The Right Hand Side Above The Stiffener At 130mm High With Overall Size Of 350mm Wide And 430mm High And 410mm Deep. The Top Of Table Shall Be Provided With Pre-laminated Particle Board Of 18 19mm Thick With Teak Veener Shade And Pvc Edging Alround The Table .hard Rubber Pvc Toes Shall Be Provided To The Legs. Locking Device Shall Be Provided To Drawers. All Steel Surfaces Exposed To View Shall Be Given Two Coats Ofwhite Or Silver Grey Or As Aaproved By Ge Enamel Paint Over A Coat Of Primer With Spray Machine After Preparation Of Steel Surfaces. Rest All As Per Drgs., Almirah Medium Steel With Shelves Dimension Overall Size Shall Be 1270mm High,765mm Wide And 440mm Deep. Description The Base Shall Be Made Of Two Numbers Mild Steel Sheet Channel Base Welded To Bottom Of Almirah And Shall Be 100mm High. Mild Steel Sheet Shall Be 1mm Thick For Channel Base. The Base Channel Shall Be Welded At 50mm From Each End Of 765mm Length And Shall Be Up To Full Width Of 440mm Of Almirah. Top Sides Back Bottom And Front Of Almirah Shall Be Of 1mm Thick Mild Steel Sheet. Three Shelves Equally Spaced Making Four Compartments Shall Be Provided And Shall Be Of 1mm Thick Mild Steel Sheet.front Shutters Shall Have Two Leaves.all Joints And Welding Fixing Shall Be Done According Standard Workmanship Handle A Steel Chromium Plated Handle 100mm Long Shall Be Provided To The Shutter. Locking Device The Locking Device Shall Be Three Way Locking Device And Shall Also Be Provided With Decorative Key Plate .make Of Lock Harrison Godrej. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted In Dual Colur Over A Coat Of Primer With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Left Top Corner Of Front Shutter Of Visisble Colour As Directed By Engr In Charge.rest All As Per Drgs, Sofa Set 5 Seater Dimension Overall Size Of One Seat Shall Be 670mm Long And 745 Mm Wide And 530mm High Up To Arm Rest Level. Description The Sofa Set 2 Seater Shall Consist Of Two Single Seats. All Wood Shall Be Of First Class Teak Wood Mp.legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front . Front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides. 100mm Thick Seat Cushion And Back Cushions Shall Be Of Size 530mm X 560mm One Numbers In Seat And One Numbers In The Back. The Cushion Shall Be Of Cool Foam Or Any Other Superior Quality Foam Of 40 Density As Approved By Engineer In Charge. Cushion Shall Be Covered With Approved Color Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Or As Directed Byengineer In Charge. Finish All Wood Surface Exposed To View When Placed In Position Shall Be French Polished With Lacquer Finish Rest.rest All As Per Drg. Dimension Overall Size Of The Three Seat Shall Be 1730mm Long 745mm Wide And 530mm High. Description The Set Consist Of One Long Piece Of Three Seat Only. Well Seasoned Teak Wood Throughout In Frame Work Shall Be Used For Manufacturing Of Sofa.ll Wood Shall Be Of First Class Teak Wood Mp Legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front .front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides.100mm Thick Cushion Of 40 Density Covered With Best Quality Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Shall Be Provided At Seat And Back As Directed By Engr In Charge. Make Of Cushion Kurlon Sleepwell Nindiya. Finish All Wooden Surfaces Internally And Externally Shall Be Melamine Polished With High Lacquer Finish Of Walnut Shade After Properly Smoothened The Surface With Sand Emery Paper. Rest All Specifications Are As Per Drg., Table Centre Dimension Overall Size Shall Be 900mm Long, 450mm Wide And 400mm High. Description All Wood Shall Be Of Teak Wood. Top Of The Table Shall Be Of 18mm Thick Prelaminated Mdf Board Of Approved Shade With 4mm Thick Teak Wood Beading All-round The Edges Of Top.legs Shall Be Made Out Of 60mmx30mm In Section Teak Wood And 356 Mm High. Bottom Rail Of Teak Wood Of 20mmx50mm In Section And 420mm Long Shall Be Provided Between Legs, Widthwise At 100mm Above The Bottom Of Legs.the Bottom Tier Shall Be Fixed On The Top Of Bottom Side Rails With 50mm Long Screwss.the Bottom Tier Shall Be Of 18mm Thick Prelaminated Particle Board Exterior Grade Of Approved Shade With 4mm Thick Teak Wood Beading All-round The Edges Of Both The Tops.25mm Dia Hard Rubber Pvc Rings Shall Be Fixed To The Bottom Of All Legs Fixed With 30mm Long Screws. Finish All Wood Surfaces Shall Be French Polished With High Gloss Finish Rest All As Per Drg., Book Case Steel Dimension Over All Size Shall Be Of 840 Mm Long 310 Mm Wide And 1675 Mm High . Description All Sheet Shall Be Mild Steel Sheet 1 Mm Thick Back Sides Bottom Top And Shelves.the Book Case Shall Be Provided With Four Compartments Of Equal Size. The Shutters Of Each Compartment Shall Open Towards Top And Slide Into The Depth Of The Book Case.transparent Glass 4mm Thick Shall Be Provided To Front Shutters. Two Steel Handles Of 100 Mm Long Shall Be Provided To Each Shutter Of The Compartment. The Locking Device Shall Be Provided To Each Compartment With Duplicate Key And Each Shutter Shall Be Provided With Decorative Key Plate .make Of Lock Godrej Harrison Link Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted In Dual Colur Over A Coat Of Primer With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Left Top Corner Of Front Shutter Of Visisble Colour As Directed By Engr In Charge.rest All As Per Drgs, Desk Stand Lecture Dimension Over All Size Shall Be 970mm Wide And 1220mm High. Description Two Upright Of Mild Steel Rectangular Tube Of 75mmx25mm Of 1202mm High Shall Be Provided In Rear Side And Shall Be 635mm Apart. The Two Upright Shall Be Joinded With Bottom, Middle And Top Rails With 75mmx50mm Mild Steel Tube Of Wal Thickness 1.6mm. The Two Sides Rails At Bottom Fixed At 125mm From Bottom Shall Be 430mm Long 75mmx50mm Mild Steel Tube Of Wall Thickness 1.6mm And Shall Form The Part Of Bottom Rails And Join The Long Side Of Bottom Rail Of Size 785mm Long, . All Edges Of Pre-laminated Particle Board Remained Exposed Shall Be Covered With Teak Wood Edging As Per The Size Of Board Edging. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Given Two Coats Of Enamel Paint Over A Coat Of Primer With Spray Machine After Preparation Of Steel Surfaces And All Wooden Surfaces Shall Be Melamine Polish With Lacquer Finish As Approved By Engr In Charge.rest All As Per Drgs, Table Computer Dimension Overall Size Of Top Shall Be 900mm Long 561.20 Mm Wide And 750mm High. Description All Prelaminated Particle Board Used In Manufacturing Of Top Shelves Drawers Tray Shall Be Of 18mm Thick Prelaminated Mdf Board. The Frame Of Table Shall Be Of 25mm Square Pipe Of Wall Thickness Not Lss Than 1.6mm. The Top Of Table Shall Be Provided With 4mm Thick Teak Wood Beading.the Legs Shall Be Made Out Of 25mmx50mm Ms Rectangular Cr Pipe Of 18 Guage.each Leg Shall Be Provided With Rectangular Pvc Cover Made To Shape On Front Sides Only. The Drawers Shall Be Provided With Telescopic Channel 300mm Long.the Legs Shall Also Be Provided With Nylon Buffers .rest All As Per Drg. Finish All Wood Surfaces Shall Be French Polished With High Gloss Finish Rest All As Per Drg., Rack Pigeon Holes Steel Dimension Over All Size Shall Be Of 1905x610x915mm. Description The Entire Rack Shall Be Made Of 1mm Mild Steel Sheet.the Sides Shall Be Provided With 40x40x4mm Angle Iron Welded To 1.00mm Thick Ms Sheet.75x75x3mm Thick Flat Iron Cut To Shape Shall Be Welded At Front Corner.all Partitions Shall Also Be Made Of 1mm Thick Mild Steel Sheet And Welded To Each Other In Continous. All Dimensions, Shape And Size Shall Be Followed As Per Drg. All Joints, Fixing Shallbe Done In Accordance With Standard Specifications. Rest All As Shown On Drg. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted With Two Coats Of Silver Grey Hammer Paint Internally And Extrenally With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Top Left Side With Visible Colour. Painting Shall Be Done With Spray Machine.rest All As Per Drg., Table Plotting Executive Size 1500x750x750mm, Controller Desk, Sofa Set 3 Seater Dimension Overall Size Of The Three Seat Shall Be 1730mm Long 745mm Wide And 530mm High. Description The Set Consist Of One Long Piece Of Three Seat Only.well Seasoned Teak Wood Throughout In Frame Work Shall Be Used For Manufacturing Of Sofa.all Wood Shall Be Of First Class Teak Wood Mp Legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front .front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides.100mm Thick Cushion Of 40 Density Covered With Best Quality Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Shall Be Provided At Seat And Back As Directed By Engr In Charge. Make Of Cushion Kurlon Sleepwell Nindiya. Finish All Wooden Surfaces Internally And Externally Shall Be Melamine Polished With High Lacquer Finish Of Walnut Shade After Properly Smoothened The Surface With Sand Emery Paper.rest All Specifications Are As Per Drg., Board Notice 2400x1220mm All Details As Per Drg. in Bihar.

Eligibility for outstation bidders depends entirely on the terms set inside the document for Tender For Revolving Chair (v5) (q2) , Steel Filing Cabinets For General Office Purpose (v2) As Per Is 3313 (q2) , Chair For General Purpose (q2) , Chair Writing With Cushion , Table Office Clerk Fd 1004 , Almirah Medium Steel With Shelves Fd 1032 , Sofa Set 5 Seater Fd 281 , Table Centre Fd 375 , Book Case Steel Fd 1028 , Desk Stand Lecture Fd 1028 , Table Computer Fd E6 Map 03 , Rack Pigeon Holes Steel Fd 1037 , Table Plotting Executive Tp , Controller Desk Tp , Sofa Set 3 Seater Fd 281 , Board Notice Fd 99 M, Tp Fur For Atc Building Bihta, Chair Writing With Cushion Dimension The Overall Size Of The Chair Shall Approx Be 950mm High 500mmwide Description It Shall Be Of Trade Pattern And Of One Make And Model As Described.the Size Dimensions Of The Chair Shall Meet The Overall Specification As Described.the Frame Of The Chair Shall Be Of Ms Tubular Frame Powder Coated Cantilever Type Of Size 25mmx10mm In Section. Back Form Shall Be Designed With Contoured Lumber Support For Extra Comfort.120mm Thick Hot Pressed Plywood Upholstered With Fabric And Moulded Polyurethane Foam With Pvc Lipping Alround Shall Be Provided At Seat And Back.arm Rest Shall Be Of Black Integral Skin Poly Urethane With Shore A Hardness And Reinforced With Ms Insert. It Shall Be Scratch And Wheather Resistant.both Hand Rest Section Shall Have Inner And Outer Dia Of 210mm And 230mm Respectively And Have Slope Towards Front. Finish Pre Treated With Epoxy Powder Caoted Oven Baked With Ivory White Colour White Warmgrey., Table Office Clk Table Office Clerk Steel Fd 1004 Overall Size Shall Be 1200mm Long, 610mm Wide And 760mm High. Steel Frame Shall Be Of Size 1160x570x742mm .four Legs Of 25mm Mild Steel Tube Of 1.6mm Wall Thickness Shall Be Provided. Top Of Legs Shall Be Joined Together With 25mm Square Mild Steel Tube Of Wall Thickness 1.6mm In Long And Short Sides. Two Short Stiffeners F Same Size Shall Be Provided At 130mm From Bottom Of Legs. One Long Stiffener Shall Also Be Provided To The Middle Of Short Stiffeners. Three Drawers Of Equal Size Shall Be Provided On The Right Hand Side Above The Stiffener At 130mm High With Overall Size Of 350mm Wide And 430mm High And 410mm Deep. The Top Of Table Shall Be Provided With Pre-laminated Particle Board Of 18 19mm Thick With Teak Veener Shade And Pvc Edging Alround The Table .hard Rubber Pvc Toes Shall Be Provided To The Legs. Locking Device Shall Be Provided To Drawers. All Steel Surfaces Exposed To View Shall Be Given Two Coats Ofwhite Or Silver Grey Or As Aaproved By Ge Enamel Paint Over A Coat Of Primer With Spray Machine After Preparation Of Steel Surfaces. Rest All As Per Drgs., Almirah Medium Steel With Shelves Dimension Overall Size Shall Be 1270mm High,765mm Wide And 440mm Deep. Description The Base Shall Be Made Of Two Numbers Mild Steel Sheet Channel Base Welded To Bottom Of Almirah And Shall Be 100mm High. Mild Steel Sheet Shall Be 1mm Thick For Channel Base. The Base Channel Shall Be Welded At 50mm From Each End Of 765mm Length And Shall Be Up To Full Width Of 440mm Of Almirah. Top Sides Back Bottom And Front Of Almirah Shall Be Of 1mm Thick Mild Steel Sheet. Three Shelves Equally Spaced Making Four Compartments Shall Be Provided And Shall Be Of 1mm Thick Mild Steel Sheet.front Shutters Shall Have Two Leaves.all Joints And Welding Fixing Shall Be Done According Standard Workmanship Handle A Steel Chromium Plated Handle 100mm Long Shall Be Provided To The Shutter. Locking Device The Locking Device Shall Be Three Way Locking Device And Shall Also Be Provided With Decorative Key Plate .make Of Lock Harrison Godrej. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted In Dual Colur Over A Coat Of Primer With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Left Top Corner Of Front Shutter Of Visisble Colour As Directed By Engr In Charge.rest All As Per Drgs, Sofa Set 5 Seater Dimension Overall Size Of One Seat Shall Be 670mm Long And 745 Mm Wide And 530mm High Up To Arm Rest Level. Description The Sofa Set 2 Seater Shall Consist Of Two Single Seats. All Wood Shall Be Of First Class Teak Wood Mp.legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front . Front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides. 100mm Thick Seat Cushion And Back Cushions Shall Be Of Size 530mm X 560mm One Numbers In Seat And One Numbers In The Back. The Cushion Shall Be Of Cool Foam Or Any Other Superior Quality Foam Of 40 Density As Approved By Engineer In Charge. Cushion Shall Be Covered With Approved Color Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Or As Directed Byengineer In Charge. Finish All Wood Surface Exposed To View When Placed In Position Shall Be French Polished With Lacquer Finish Rest.rest All As Per Drg. Dimension Overall Size Of The Three Seat Shall Be 1730mm Long 745mm Wide And 530mm High. Description The Set Consist Of One Long Piece Of Three Seat Only. Well Seasoned Teak Wood Throughout In Frame Work Shall Be Used For Manufacturing Of Sofa.ll Wood Shall Be Of First Class Teak Wood Mp Legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front .front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides.100mm Thick Cushion Of 40 Density Covered With Best Quality Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Shall Be Provided At Seat And Back As Directed By Engr In Charge. Make Of Cushion Kurlon Sleepwell Nindiya. Finish All Wooden Surfaces Internally And Externally Shall Be Melamine Polished With High Lacquer Finish Of Walnut Shade After Properly Smoothened The Surface With Sand Emery Paper. Rest All Specifications Are As Per Drg., Table Centre Dimension Overall Size Shall Be 900mm Long, 450mm Wide And 400mm High. Description All Wood Shall Be Of Teak Wood. Top Of The Table Shall Be Of 18mm Thick Prelaminated Mdf Board Of Approved Shade With 4mm Thick Teak Wood Beading All-round The Edges Of Top.legs Shall Be Made Out Of 60mmx30mm In Section Teak Wood And 356 Mm High. Bottom Rail Of Teak Wood Of 20mmx50mm In Section And 420mm Long Shall Be Provided Between Legs, Widthwise At 100mm Above The Bottom Of Legs.the Bottom Tier Shall Be Fixed On The Top Of Bottom Side Rails With 50mm Long Screwss.the Bottom Tier Shall Be Of 18mm Thick Prelaminated Particle Board Exterior Grade Of Approved Shade With 4mm Thick Teak Wood Beading All-round The Edges Of Both The Tops.25mm Dia Hard Rubber Pvc Rings Shall Be Fixed To The Bottom Of All Legs Fixed With 30mm Long Screws. Finish All Wood Surfaces Shall Be French Polished With High Gloss Finish Rest All As Per Drg., Book Case Steel Dimension Over All Size Shall Be Of 840 Mm Long 310 Mm Wide And 1675 Mm High . Description All Sheet Shall Be Mild Steel Sheet 1 Mm Thick Back Sides Bottom Top And Shelves.the Book Case Shall Be Provided With Four Compartments Of Equal Size. The Shutters Of Each Compartment Shall Open Towards Top And Slide Into The Depth Of The Book Case.transparent Glass 4mm Thick Shall Be Provided To Front Shutters. Two Steel Handles Of 100 Mm Long Shall Be Provided To Each Shutter Of The Compartment. The Locking Device Shall Be Provided To Each Compartment With Duplicate Key And Each Shutter Shall Be Provided With Decorative Key Plate .make Of Lock Godrej Harrison Link Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted In Dual Colur Over A Coat Of Primer With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Left Top Corner Of Front Shutter Of Visisble Colour As Directed By Engr In Charge.rest All As Per Drgs, Desk Stand Lecture Dimension Over All Size Shall Be 970mm Wide And 1220mm High. Description Two Upright Of Mild Steel Rectangular Tube Of 75mmx25mm Of 1202mm High Shall Be Provided In Rear Side And Shall Be 635mm Apart. The Two Upright Shall Be Joinded With Bottom, Middle And Top Rails With 75mmx50mm Mild Steel Tube Of Wal Thickness 1.6mm. The Two Sides Rails At Bottom Fixed At 125mm From Bottom Shall Be 430mm Long 75mmx50mm Mild Steel Tube Of Wall Thickness 1.6mm And Shall Form The Part Of Bottom Rails And Join The Long Side Of Bottom Rail Of Size 785mm Long, . All Edges Of Pre-laminated Particle Board Remained Exposed Shall Be Covered With Teak Wood Edging As Per The Size Of Board Edging. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Given Two Coats Of Enamel Paint Over A Coat Of Primer With Spray Machine After Preparation Of Steel Surfaces And All Wooden Surfaces Shall Be Melamine Polish With Lacquer Finish As Approved By Engr In Charge.rest All As Per Drgs, Table Computer Dimension Overall Size Of Top Shall Be 900mm Long 561.20 Mm Wide And 750mm High. Description All Prelaminated Particle Board Used In Manufacturing Of Top Shelves Drawers Tray Shall Be Of 18mm Thick Prelaminated Mdf Board. The Frame Of Table Shall Be Of 25mm Square Pipe Of Wall Thickness Not Lss Than 1.6mm. The Top Of Table Shall Be Provided With 4mm Thick Teak Wood Beading.the Legs Shall Be Made Out Of 25mmx50mm Ms Rectangular Cr Pipe Of 18 Guage.each Leg Shall Be Provided With Rectangular Pvc Cover Made To Shape On Front Sides Only. The Drawers Shall Be Provided With Telescopic Channel 300mm Long.the Legs Shall Also Be Provided With Nylon Buffers .rest All As Per Drg. Finish All Wood Surfaces Shall Be French Polished With High Gloss Finish Rest All As Per Drg., Rack Pigeon Holes Steel Dimension Over All Size Shall Be Of 1905x610x915mm. Description The Entire Rack Shall Be Made Of 1mm Mild Steel Sheet.the Sides Shall Be Provided With 40x40x4mm Angle Iron Welded To 1.00mm Thick Ms Sheet.75x75x3mm Thick Flat Iron Cut To Shape Shall Be Welded At Front Corner.all Partitions Shall Also Be Made Of 1mm Thick Mild Steel Sheet And Welded To Each Other In Continous. All Dimensions, Shape And Size Shall Be Followed As Per Drg. All Joints, Fixing Shallbe Done In Accordance With Standard Specifications. Rest All As Shown On Drg. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted With Two Coats Of Silver Grey Hammer Paint Internally And Extrenally With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Top Left Side With Visible Colour. Painting Shall Be Done With Spray Machine.rest All As Per Drg., Table Plotting Executive Size 1500x750x750mm, Controller Desk, Sofa Set 3 Seater Dimension Overall Size Of The Three Seat Shall Be 1730mm Long 745mm Wide And 530mm High. Description The Set Consist Of One Long Piece Of Three Seat Only.well Seasoned Teak Wood Throughout In Frame Work Shall Be Used For Manufacturing Of Sofa.all Wood Shall Be Of First Class Teak Wood Mp Legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front .front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides.100mm Thick Cushion Of 40 Density Covered With Best Quality Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Shall Be Provided At Seat And Back As Directed By Engr In Charge. Make Of Cushion Kurlon Sleepwell Nindiya. Finish All Wooden Surfaces Internally And Externally Shall Be Melamine Polished With High Lacquer Finish Of Walnut Shade After Properly Smoothened The Surface With Sand Emery Paper.rest All Specifications Are As Per Drg., Board Notice 2400x1220mm All Details As Per Drg.. While many public sector projects allow national competitive bidding, certain localized works require local offices or specific registration metrics in Patna.

If this procurement is routed through the central marketplace, an active GeM Seller ID is mandatory to supply items. Tender18 offers complete assistance for brand cataloging, profile creation, and vendor assessment required officially by Indian Army

To register an eligible bid for these contracts, companies must prepare their core compliance documents. Vendors operating across Bihar must ensure they possess a valid GST registration, permanent account number (PAN), and active Class-3 Digital Signature Certificates.

This public procurement cycle is specifically looking for qualified vendors and suppliers who can provide high-quality solutions. The operational execution, delivery, and deployment of these materials must be managed locally within the Patna region.

The estimated project cost and budget thresholds can be reviewed directly inside the tender document. Bidders can analyze these qualification files to check if their firm meets the financial capability criteria specified for Tender For Revolving Chair (v5) (q2) , Steel Filing Cabinets For General Office Purpose (v2) As Per Is 3313 (q2) , Chair For General Purpose (q2) , Chair Writing With Cushion , Table Office Clerk Fd 1004 , Almirah Medium Steel With Shelves Fd 1032 , Sofa Set 5 Seater Fd 281 , Table Centre Fd 375 , Book Case Steel Fd 1028 , Desk Stand Lecture Fd 1028 , Table Computer Fd E6 Map 03 , Rack Pigeon Holes Steel Fd 1037 , Table Plotting Executive Tp , Controller Desk Tp , Sofa Set 3 Seater Fd 281 , Board Notice Fd 99 M, Tp Fur For Atc Building Bihta, Chair Writing With Cushion Dimension The Overall Size Of The Chair Shall Approx Be 950mm High 500mmwide Description It Shall Be Of Trade Pattern And Of One Make And Model As Described.the Size Dimensions Of The Chair Shall Meet The Overall Specification As Described.the Frame Of The Chair Shall Be Of Ms Tubular Frame Powder Coated Cantilever Type Of Size 25mmx10mm In Section. Back Form Shall Be Designed With Contoured Lumber Support For Extra Comfort.120mm Thick Hot Pressed Plywood Upholstered With Fabric And Moulded Polyurethane Foam With Pvc Lipping Alround Shall Be Provided At Seat And Back.arm Rest Shall Be Of Black Integral Skin Poly Urethane With Shore A Hardness And Reinforced With Ms Insert. It Shall Be Scratch And Wheather Resistant.both Hand Rest Section Shall Have Inner And Outer Dia Of 210mm And 230mm Respectively And Have Slope Towards Front. Finish Pre Treated With Epoxy Powder Caoted Oven Baked With Ivory White Colour White Warmgrey., Table Office Clk Table Office Clerk Steel Fd 1004 Overall Size Shall Be 1200mm Long, 610mm Wide And 760mm High. Steel Frame Shall Be Of Size 1160x570x742mm .four Legs Of 25mm Mild Steel Tube Of 1.6mm Wall Thickness Shall Be Provided. Top Of Legs Shall Be Joined Together With 25mm Square Mild Steel Tube Of Wall Thickness 1.6mm In Long And Short Sides. Two Short Stiffeners F Same Size Shall Be Provided At 130mm From Bottom Of Legs. One Long Stiffener Shall Also Be Provided To The Middle Of Short Stiffeners. Three Drawers Of Equal Size Shall Be Provided On The Right Hand Side Above The Stiffener At 130mm High With Overall Size Of 350mm Wide And 430mm High And 410mm Deep. The Top Of Table Shall Be Provided With Pre-laminated Particle Board Of 18 19mm Thick With Teak Veener Shade And Pvc Edging Alround The Table .hard Rubber Pvc Toes Shall Be Provided To The Legs. Locking Device Shall Be Provided To Drawers. All Steel Surfaces Exposed To View Shall Be Given Two Coats Ofwhite Or Silver Grey Or As Aaproved By Ge Enamel Paint Over A Coat Of Primer With Spray Machine After Preparation Of Steel Surfaces. Rest All As Per Drgs., Almirah Medium Steel With Shelves Dimension Overall Size Shall Be 1270mm High,765mm Wide And 440mm Deep. Description The Base Shall Be Made Of Two Numbers Mild Steel Sheet Channel Base Welded To Bottom Of Almirah And Shall Be 100mm High. Mild Steel Sheet Shall Be 1mm Thick For Channel Base. The Base Channel Shall Be Welded At 50mm From Each End Of 765mm Length And Shall Be Up To Full Width Of 440mm Of Almirah. Top Sides Back Bottom And Front Of Almirah Shall Be Of 1mm Thick Mild Steel Sheet. Three Shelves Equally Spaced Making Four Compartments Shall Be Provided And Shall Be Of 1mm Thick Mild Steel Sheet.front Shutters Shall Have Two Leaves.all Joints And Welding Fixing Shall Be Done According Standard Workmanship Handle A Steel Chromium Plated Handle 100mm Long Shall Be Provided To The Shutter. Locking Device The Locking Device Shall Be Three Way Locking Device And Shall Also Be Provided With Decorative Key Plate .make Of Lock Harrison Godrej. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted In Dual Colur Over A Coat Of Primer With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Left Top Corner Of Front Shutter Of Visisble Colour As Directed By Engr In Charge.rest All As Per Drgs, Sofa Set 5 Seater Dimension Overall Size Of One Seat Shall Be 670mm Long And 745 Mm Wide And 530mm High Up To Arm Rest Level. Description The Sofa Set 2 Seater Shall Consist Of Two Single Seats. All Wood Shall Be Of First Class Teak Wood Mp.legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front . Front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides. 100mm Thick Seat Cushion And Back Cushions Shall Be Of Size 530mm X 560mm One Numbers In Seat And One Numbers In The Back. The Cushion Shall Be Of Cool Foam Or Any Other Superior Quality Foam Of 40 Density As Approved By Engineer In Charge. Cushion Shall Be Covered With Approved Color Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Or As Directed Byengineer In Charge. Finish All Wood Surface Exposed To View When Placed In Position Shall Be French Polished With Lacquer Finish Rest.rest All As Per Drg. Dimension Overall Size Of The Three Seat Shall Be 1730mm Long 745mm Wide And 530mm High. Description The Set Consist Of One Long Piece Of Three Seat Only. Well Seasoned Teak Wood Throughout In Frame Work Shall Be Used For Manufacturing Of Sofa.ll Wood Shall Be Of First Class Teak Wood Mp Legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front .front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides.100mm Thick Cushion Of 40 Density Covered With Best Quality Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Shall Be Provided At Seat And Back As Directed By Engr In Charge. Make Of Cushion Kurlon Sleepwell Nindiya. Finish All Wooden Surfaces Internally And Externally Shall Be Melamine Polished With High Lacquer Finish Of Walnut Shade After Properly Smoothened The Surface With Sand Emery Paper. Rest All Specifications Are As Per Drg., Table Centre Dimension Overall Size Shall Be 900mm Long, 450mm Wide And 400mm High. Description All Wood Shall Be Of Teak Wood. Top Of The Table Shall Be Of 18mm Thick Prelaminated Mdf Board Of Approved Shade With 4mm Thick Teak Wood Beading All-round The Edges Of Top.legs Shall Be Made Out Of 60mmx30mm In Section Teak Wood And 356 Mm High. Bottom Rail Of Teak Wood Of 20mmx50mm In Section And 420mm Long Shall Be Provided Between Legs, Widthwise At 100mm Above The Bottom Of Legs.the Bottom Tier Shall Be Fixed On The Top Of Bottom Side Rails With 50mm Long Screwss.the Bottom Tier Shall Be Of 18mm Thick Prelaminated Particle Board Exterior Grade Of Approved Shade With 4mm Thick Teak Wood Beading All-round The Edges Of Both The Tops.25mm Dia Hard Rubber Pvc Rings Shall Be Fixed To The Bottom Of All Legs Fixed With 30mm Long Screws. Finish All Wood Surfaces Shall Be French Polished With High Gloss Finish Rest All As Per Drg., Book Case Steel Dimension Over All Size Shall Be Of 840 Mm Long 310 Mm Wide And 1675 Mm High . Description All Sheet Shall Be Mild Steel Sheet 1 Mm Thick Back Sides Bottom Top And Shelves.the Book Case Shall Be Provided With Four Compartments Of Equal Size. The Shutters Of Each Compartment Shall Open Towards Top And Slide Into The Depth Of The Book Case.transparent Glass 4mm Thick Shall Be Provided To Front Shutters. Two Steel Handles Of 100 Mm Long Shall Be Provided To Each Shutter Of The Compartment. The Locking Device Shall Be Provided To Each Compartment With Duplicate Key And Each Shutter Shall Be Provided With Decorative Key Plate .make Of Lock Godrej Harrison Link Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted In Dual Colur Over A Coat Of Primer With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Left Top Corner Of Front Shutter Of Visisble Colour As Directed By Engr In Charge.rest All As Per Drgs, Desk Stand Lecture Dimension Over All Size Shall Be 970mm Wide And 1220mm High. Description Two Upright Of Mild Steel Rectangular Tube Of 75mmx25mm Of 1202mm High Shall Be Provided In Rear Side And Shall Be 635mm Apart. The Two Upright Shall Be Joinded With Bottom, Middle And Top Rails With 75mmx50mm Mild Steel Tube Of Wal Thickness 1.6mm. The Two Sides Rails At Bottom Fixed At 125mm From Bottom Shall Be 430mm Long 75mmx50mm Mild Steel Tube Of Wall Thickness 1.6mm And Shall Form The Part Of Bottom Rails And Join The Long Side Of Bottom Rail Of Size 785mm Long, . All Edges Of Pre-laminated Particle Board Remained Exposed Shall Be Covered With Teak Wood Edging As Per The Size Of Board Edging. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Given Two Coats Of Enamel Paint Over A Coat Of Primer With Spray Machine After Preparation Of Steel Surfaces And All Wooden Surfaces Shall Be Melamine Polish With Lacquer Finish As Approved By Engr In Charge.rest All As Per Drgs, Table Computer Dimension Overall Size Of Top Shall Be 900mm Long 561.20 Mm Wide And 750mm High. Description All Prelaminated Particle Board Used In Manufacturing Of Top Shelves Drawers Tray Shall Be Of 18mm Thick Prelaminated Mdf Board. The Frame Of Table Shall Be Of 25mm Square Pipe Of Wall Thickness Not Lss Than 1.6mm. The Top Of Table Shall Be Provided With 4mm Thick Teak Wood Beading.the Legs Shall Be Made Out Of 25mmx50mm Ms Rectangular Cr Pipe Of 18 Guage.each Leg Shall Be Provided With Rectangular Pvc Cover Made To Shape On Front Sides Only. The Drawers Shall Be Provided With Telescopic Channel 300mm Long.the Legs Shall Also Be Provided With Nylon Buffers .rest All As Per Drg. Finish All Wood Surfaces Shall Be French Polished With High Gloss Finish Rest All As Per Drg., Rack Pigeon Holes Steel Dimension Over All Size Shall Be Of 1905x610x915mm. Description The Entire Rack Shall Be Made Of 1mm Mild Steel Sheet.the Sides Shall Be Provided With 40x40x4mm Angle Iron Welded To 1.00mm Thick Ms Sheet.75x75x3mm Thick Flat Iron Cut To Shape Shall Be Welded At Front Corner.all Partitions Shall Also Be Made Of 1mm Thick Mild Steel Sheet And Welded To Each Other In Continous. All Dimensions, Shape And Size Shall Be Followed As Per Drg. All Joints, Fixing Shallbe Done In Accordance With Standard Specifications. Rest All As Shown On Drg. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted With Two Coats Of Silver Grey Hammer Paint Internally And Extrenally With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Top Left Side With Visible Colour. Painting Shall Be Done With Spray Machine.rest All As Per Drg., Table Plotting Executive Size 1500x750x750mm, Controller Desk, Sofa Set 3 Seater Dimension Overall Size Of The Three Seat Shall Be 1730mm Long 745mm Wide And 530mm High. Description The Set Consist Of One Long Piece Of Three Seat Only.well Seasoned Teak Wood Throughout In Frame Work Shall Be Used For Manufacturing Of Sofa.all Wood Shall Be Of First Class Teak Wood Mp Legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front .front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides.100mm Thick Cushion Of 40 Density Covered With Best Quality Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Shall Be Provided At Seat And Back As Directed By Engr In Charge. Make Of Cushion Kurlon Sleepwell Nindiya. Finish All Wooden Surfaces Internally And Externally Shall Be Melamine Polished With High Lacquer Finish Of Walnut Shade After Properly Smoothened The Surface With Sand Emery Paper.rest All Specifications Are As Per Drg., Board Notice 2400x1220mm All Details As Per Drg. by Indian Army

You can download the commercial Bill of Quantities (BOQ) spreadsheet directly using the secure link provided on this page. The BOQ file contains the item descriptions and rate filling forms officially validated for Tender For Revolving Chair (v5) (q2) , Steel Filing Cabinets For General Office Purpose (v2) As Per Is 3313 (q2) , Chair For General Purpose (q2) , Chair Writing With Cushion , Table Office Clerk Fd 1004 , Almirah Medium Steel With Shelves Fd 1032 , Sofa Set 5 Seater Fd 281 , Table Centre Fd 375 , Book Case Steel Fd 1028 , Desk Stand Lecture Fd 1028 , Table Computer Fd E6 Map 03 , Rack Pigeon Holes Steel Fd 1037 , Table Plotting Executive Tp , Controller Desk Tp , Sofa Set 3 Seater Fd 281 , Board Notice Fd 99 M, Tp Fur For Atc Building Bihta, Chair Writing With Cushion Dimension The Overall Size Of The Chair Shall Approx Be 950mm High 500mmwide Description It Shall Be Of Trade Pattern And Of One Make And Model As Described.the Size Dimensions Of The Chair Shall Meet The Overall Specification As Described.the Frame Of The Chair Shall Be Of Ms Tubular Frame Powder Coated Cantilever Type Of Size 25mmx10mm In Section. Back Form Shall Be Designed With Contoured Lumber Support For Extra Comfort.120mm Thick Hot Pressed Plywood Upholstered With Fabric And Moulded Polyurethane Foam With Pvc Lipping Alround Shall Be Provided At Seat And Back.arm Rest Shall Be Of Black Integral Skin Poly Urethane With Shore A Hardness And Reinforced With Ms Insert. It Shall Be Scratch And Wheather Resistant.both Hand Rest Section Shall Have Inner And Outer Dia Of 210mm And 230mm Respectively And Have Slope Towards Front. Finish Pre Treated With Epoxy Powder Caoted Oven Baked With Ivory White Colour White Warmgrey., Table Office Clk Table Office Clerk Steel Fd 1004 Overall Size Shall Be 1200mm Long, 610mm Wide And 760mm High. Steel Frame Shall Be Of Size 1160x570x742mm .four Legs Of 25mm Mild Steel Tube Of 1.6mm Wall Thickness Shall Be Provided. Top Of Legs Shall Be Joined Together With 25mm Square Mild Steel Tube Of Wall Thickness 1.6mm In Long And Short Sides. Two Short Stiffeners F Same Size Shall Be Provided At 130mm From Bottom Of Legs. One Long Stiffener Shall Also Be Provided To The Middle Of Short Stiffeners. Three Drawers Of Equal Size Shall Be Provided On The Right Hand Side Above The Stiffener At 130mm High With Overall Size Of 350mm Wide And 430mm High And 410mm Deep. The Top Of Table Shall Be Provided With Pre-laminated Particle Board Of 18 19mm Thick With Teak Veener Shade And Pvc Edging Alround The Table .hard Rubber Pvc Toes Shall Be Provided To The Legs. Locking Device Shall Be Provided To Drawers. All Steel Surfaces Exposed To View Shall Be Given Two Coats Ofwhite Or Silver Grey Or As Aaproved By Ge Enamel Paint Over A Coat Of Primer With Spray Machine After Preparation Of Steel Surfaces. Rest All As Per Drgs., Almirah Medium Steel With Shelves Dimension Overall Size Shall Be 1270mm High,765mm Wide And 440mm Deep. Description The Base Shall Be Made Of Two Numbers Mild Steel Sheet Channel Base Welded To Bottom Of Almirah And Shall Be 100mm High. Mild Steel Sheet Shall Be 1mm Thick For Channel Base. The Base Channel Shall Be Welded At 50mm From Each End Of 765mm Length And Shall Be Up To Full Width Of 440mm Of Almirah. Top Sides Back Bottom And Front Of Almirah Shall Be Of 1mm Thick Mild Steel Sheet. Three Shelves Equally Spaced Making Four Compartments Shall Be Provided And Shall Be Of 1mm Thick Mild Steel Sheet.front Shutters Shall Have Two Leaves.all Joints And Welding Fixing Shall Be Done According Standard Workmanship Handle A Steel Chromium Plated Handle 100mm Long Shall Be Provided To The Shutter. Locking Device The Locking Device Shall Be Three Way Locking Device And Shall Also Be Provided With Decorative Key Plate .make Of Lock Harrison Godrej. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted In Dual Colur Over A Coat Of Primer With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Left Top Corner Of Front Shutter Of Visisble Colour As Directed By Engr In Charge.rest All As Per Drgs, Sofa Set 5 Seater Dimension Overall Size Of One Seat Shall Be 670mm Long And 745 Mm Wide And 530mm High Up To Arm Rest Level. Description The Sofa Set 2 Seater Shall Consist Of Two Single Seats. All Wood Shall Be Of First Class Teak Wood Mp.legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front . Front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides. 100mm Thick Seat Cushion And Back Cushions Shall Be Of Size 530mm X 560mm One Numbers In Seat And One Numbers In The Back. The Cushion Shall Be Of Cool Foam Or Any Other Superior Quality Foam Of 40 Density As Approved By Engineer In Charge. Cushion Shall Be Covered With Approved Color Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Or As Directed Byengineer In Charge. Finish All Wood Surface Exposed To View When Placed In Position Shall Be French Polished With Lacquer Finish Rest.rest All As Per Drg. Dimension Overall Size Of The Three Seat Shall Be 1730mm Long 745mm Wide And 530mm High. Description The Set Consist Of One Long Piece Of Three Seat Only. Well Seasoned Teak Wood Throughout In Frame Work Shall Be Used For Manufacturing Of Sofa.ll Wood Shall Be Of First Class Teak Wood Mp Legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front .front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides.100mm Thick Cushion Of 40 Density Covered With Best Quality Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Shall Be Provided At Seat And Back As Directed By Engr In Charge. Make Of Cushion Kurlon Sleepwell Nindiya. Finish All Wooden Surfaces Internally And Externally Shall Be Melamine Polished With High Lacquer Finish Of Walnut Shade After Properly Smoothened The Surface With Sand Emery Paper. Rest All Specifications Are As Per Drg., Table Centre Dimension Overall Size Shall Be 900mm Long, 450mm Wide And 400mm High. Description All Wood Shall Be Of Teak Wood. Top Of The Table Shall Be Of 18mm Thick Prelaminated Mdf Board Of Approved Shade With 4mm Thick Teak Wood Beading All-round The Edges Of Top.legs Shall Be Made Out Of 60mmx30mm In Section Teak Wood And 356 Mm High. Bottom Rail Of Teak Wood Of 20mmx50mm In Section And 420mm Long Shall Be Provided Between Legs, Widthwise At 100mm Above The Bottom Of Legs.the Bottom Tier Shall Be Fixed On The Top Of Bottom Side Rails With 50mm Long Screwss.the Bottom Tier Shall Be Of 18mm Thick Prelaminated Particle Board Exterior Grade Of Approved Shade With 4mm Thick Teak Wood Beading All-round The Edges Of Both The Tops.25mm Dia Hard Rubber Pvc Rings Shall Be Fixed To The Bottom Of All Legs Fixed With 30mm Long Screws. Finish All Wood Surfaces Shall Be French Polished With High Gloss Finish Rest All As Per Drg., Book Case Steel Dimension Over All Size Shall Be Of 840 Mm Long 310 Mm Wide And 1675 Mm High . Description All Sheet Shall Be Mild Steel Sheet 1 Mm Thick Back Sides Bottom Top And Shelves.the Book Case Shall Be Provided With Four Compartments Of Equal Size. The Shutters Of Each Compartment Shall Open Towards Top And Slide Into The Depth Of The Book Case.transparent Glass 4mm Thick Shall Be Provided To Front Shutters. Two Steel Handles Of 100 Mm Long Shall Be Provided To Each Shutter Of The Compartment. The Locking Device Shall Be Provided To Each Compartment With Duplicate Key And Each Shutter Shall Be Provided With Decorative Key Plate .make Of Lock Godrej Harrison Link Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted In Dual Colur Over A Coat Of Primer With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Left Top Corner Of Front Shutter Of Visisble Colour As Directed By Engr In Charge.rest All As Per Drgs, Desk Stand Lecture Dimension Over All Size Shall Be 970mm Wide And 1220mm High. Description Two Upright Of Mild Steel Rectangular Tube Of 75mmx25mm Of 1202mm High Shall Be Provided In Rear Side And Shall Be 635mm Apart. The Two Upright Shall Be Joinded With Bottom, Middle And Top Rails With 75mmx50mm Mild Steel Tube Of Wal Thickness 1.6mm. The Two Sides Rails At Bottom Fixed At 125mm From Bottom Shall Be 430mm Long 75mmx50mm Mild Steel Tube Of Wall Thickness 1.6mm And Shall Form The Part Of Bottom Rails And Join The Long Side Of Bottom Rail Of Size 785mm Long, . All Edges Of Pre-laminated Particle Board Remained Exposed Shall Be Covered With Teak Wood Edging As Per The Size Of Board Edging. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Given Two Coats Of Enamel Paint Over A Coat Of Primer With Spray Machine After Preparation Of Steel Surfaces And All Wooden Surfaces Shall Be Melamine Polish With Lacquer Finish As Approved By Engr In Charge.rest All As Per Drgs, Table Computer Dimension Overall Size Of Top Shall Be 900mm Long 561.20 Mm Wide And 750mm High. Description All Prelaminated Particle Board Used In Manufacturing Of Top Shelves Drawers Tray Shall Be Of 18mm Thick Prelaminated Mdf Board. The Frame Of Table Shall Be Of 25mm Square Pipe Of Wall Thickness Not Lss Than 1.6mm. The Top Of Table Shall Be Provided With 4mm Thick Teak Wood Beading.the Legs Shall Be Made Out Of 25mmx50mm Ms Rectangular Cr Pipe Of 18 Guage.each Leg Shall Be Provided With Rectangular Pvc Cover Made To Shape On Front Sides Only. The Drawers Shall Be Provided With Telescopic Channel 300mm Long.the Legs Shall Also Be Provided With Nylon Buffers .rest All As Per Drg. Finish All Wood Surfaces Shall Be French Polished With High Gloss Finish Rest All As Per Drg., Rack Pigeon Holes Steel Dimension Over All Size Shall Be Of 1905x610x915mm. Description The Entire Rack Shall Be Made Of 1mm Mild Steel Sheet.the Sides Shall Be Provided With 40x40x4mm Angle Iron Welded To 1.00mm Thick Ms Sheet.75x75x3mm Thick Flat Iron Cut To Shape Shall Be Welded At Front Corner.all Partitions Shall Also Be Made Of 1mm Thick Mild Steel Sheet And Welded To Each Other In Continous. All Dimensions, Shape And Size Shall Be Followed As Per Drg. All Joints, Fixing Shallbe Done In Accordance With Standard Specifications. Rest All As Shown On Drg. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted With Two Coats Of Silver Grey Hammer Paint Internally And Extrenally With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Top Left Side With Visible Colour. Painting Shall Be Done With Spray Machine.rest All As Per Drg., Table Plotting Executive Size 1500x750x750mm, Controller Desk, Sofa Set 3 Seater Dimension Overall Size Of The Three Seat Shall Be 1730mm Long 745mm Wide And 530mm High. Description The Set Consist Of One Long Piece Of Three Seat Only.well Seasoned Teak Wood Throughout In Frame Work Shall Be Used For Manufacturing Of Sofa.all Wood Shall Be Of First Class Teak Wood Mp Legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front .front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides.100mm Thick Cushion Of 40 Density Covered With Best Quality Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Shall Be Provided At Seat And Back As Directed By Engr In Charge. Make Of Cushion Kurlon Sleepwell Nindiya. Finish All Wooden Surfaces Internally And Externally Shall Be Melamine Polished With High Lacquer Finish Of Walnut Shade After Properly Smoothened The Surface With Sand Emery Paper.rest All Specifications Are As Per Drg., Board Notice 2400x1220mm All Details As Per Drg. within the Bihar jurisdiction

The official timeline and deadline details for Tender For Revolving Chair (v5) (q2) , Steel Filing Cabinets For General Office Purpose (v2) As Per Is 3313 (q2) , Chair For General Purpose (q2) , Chair Writing With Cushion , Table Office Clerk Fd 1004 , Almirah Medium Steel With Shelves Fd 1032 , Sofa Set 5 Seater Fd 281 , Table Centre Fd 375 , Book Case Steel Fd 1028 , Desk Stand Lecture Fd 1028 , Table Computer Fd E6 Map 03 , Rack Pigeon Holes Steel Fd 1037 , Table Plotting Executive Tp , Controller Desk Tp , Sofa Set 3 Seater Fd 281 , Board Notice Fd 99 M, Tp Fur For Atc Building Bihta, Chair Writing With Cushion Dimension The Overall Size Of The Chair Shall Approx Be 950mm High 500mmwide Description It Shall Be Of Trade Pattern And Of One Make And Model As Described.the Size Dimensions Of The Chair Shall Meet The Overall Specification As Described.the Frame Of The Chair Shall Be Of Ms Tubular Frame Powder Coated Cantilever Type Of Size 25mmx10mm In Section. Back Form Shall Be Designed With Contoured Lumber Support For Extra Comfort.120mm Thick Hot Pressed Plywood Upholstered With Fabric And Moulded Polyurethane Foam With Pvc Lipping Alround Shall Be Provided At Seat And Back.arm Rest Shall Be Of Black Integral Skin Poly Urethane With Shore A Hardness And Reinforced With Ms Insert. It Shall Be Scratch And Wheather Resistant.both Hand Rest Section Shall Have Inner And Outer Dia Of 210mm And 230mm Respectively And Have Slope Towards Front. Finish Pre Treated With Epoxy Powder Caoted Oven Baked With Ivory White Colour White Warmgrey., Table Office Clk Table Office Clerk Steel Fd 1004 Overall Size Shall Be 1200mm Long, 610mm Wide And 760mm High. Steel Frame Shall Be Of Size 1160x570x742mm .four Legs Of 25mm Mild Steel Tube Of 1.6mm Wall Thickness Shall Be Provided. Top Of Legs Shall Be Joined Together With 25mm Square Mild Steel Tube Of Wall Thickness 1.6mm In Long And Short Sides. Two Short Stiffeners F Same Size Shall Be Provided At 130mm From Bottom Of Legs. One Long Stiffener Shall Also Be Provided To The Middle Of Short Stiffeners. Three Drawers Of Equal Size Shall Be Provided On The Right Hand Side Above The Stiffener At 130mm High With Overall Size Of 350mm Wide And 430mm High And 410mm Deep. The Top Of Table Shall Be Provided With Pre-laminated Particle Board Of 18 19mm Thick With Teak Veener Shade And Pvc Edging Alround The Table .hard Rubber Pvc Toes Shall Be Provided To The Legs. Locking Device Shall Be Provided To Drawers. All Steel Surfaces Exposed To View Shall Be Given Two Coats Ofwhite Or Silver Grey Or As Aaproved By Ge Enamel Paint Over A Coat Of Primer With Spray Machine After Preparation Of Steel Surfaces. Rest All As Per Drgs., Almirah Medium Steel With Shelves Dimension Overall Size Shall Be 1270mm High,765mm Wide And 440mm Deep. Description The Base Shall Be Made Of Two Numbers Mild Steel Sheet Channel Base Welded To Bottom Of Almirah And Shall Be 100mm High. Mild Steel Sheet Shall Be 1mm Thick For Channel Base. The Base Channel Shall Be Welded At 50mm From Each End Of 765mm Length And Shall Be Up To Full Width Of 440mm Of Almirah. Top Sides Back Bottom And Front Of Almirah Shall Be Of 1mm Thick Mild Steel Sheet. Three Shelves Equally Spaced Making Four Compartments Shall Be Provided And Shall Be Of 1mm Thick Mild Steel Sheet.front Shutters Shall Have Two Leaves.all Joints And Welding Fixing Shall Be Done According Standard Workmanship Handle A Steel Chromium Plated Handle 100mm Long Shall Be Provided To The Shutter. Locking Device The Locking Device Shall Be Three Way Locking Device And Shall Also Be Provided With Decorative Key Plate .make Of Lock Harrison Godrej. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted In Dual Colur Over A Coat Of Primer With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Left Top Corner Of Front Shutter Of Visisble Colour As Directed By Engr In Charge.rest All As Per Drgs, Sofa Set 5 Seater Dimension Overall Size Of One Seat Shall Be 670mm Long And 745 Mm Wide And 530mm High Up To Arm Rest Level. Description The Sofa Set 2 Seater Shall Consist Of Two Single Seats. All Wood Shall Be Of First Class Teak Wood Mp.legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front . Front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides. 100mm Thick Seat Cushion And Back Cushions Shall Be Of Size 530mm X 560mm One Numbers In Seat And One Numbers In The Back. The Cushion Shall Be Of Cool Foam Or Any Other Superior Quality Foam Of 40 Density As Approved By Engineer In Charge. Cushion Shall Be Covered With Approved Color Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Or As Directed Byengineer In Charge. Finish All Wood Surface Exposed To View When Placed In Position Shall Be French Polished With Lacquer Finish Rest.rest All As Per Drg. Dimension Overall Size Of The Three Seat Shall Be 1730mm Long 745mm Wide And 530mm High. Description The Set Consist Of One Long Piece Of Three Seat Only. Well Seasoned Teak Wood Throughout In Frame Work Shall Be Used For Manufacturing Of Sofa.ll Wood Shall Be Of First Class Teak Wood Mp Legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front .front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides.100mm Thick Cushion Of 40 Density Covered With Best Quality Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Shall Be Provided At Seat And Back As Directed By Engr In Charge. Make Of Cushion Kurlon Sleepwell Nindiya. Finish All Wooden Surfaces Internally And Externally Shall Be Melamine Polished With High Lacquer Finish Of Walnut Shade After Properly Smoothened The Surface With Sand Emery Paper. Rest All Specifications Are As Per Drg., Table Centre Dimension Overall Size Shall Be 900mm Long, 450mm Wide And 400mm High. Description All Wood Shall Be Of Teak Wood. Top Of The Table Shall Be Of 18mm Thick Prelaminated Mdf Board Of Approved Shade With 4mm Thick Teak Wood Beading All-round The Edges Of Top.legs Shall Be Made Out Of 60mmx30mm In Section Teak Wood And 356 Mm High. Bottom Rail Of Teak Wood Of 20mmx50mm In Section And 420mm Long Shall Be Provided Between Legs, Widthwise At 100mm Above The Bottom Of Legs.the Bottom Tier Shall Be Fixed On The Top Of Bottom Side Rails With 50mm Long Screwss.the Bottom Tier Shall Be Of 18mm Thick Prelaminated Particle Board Exterior Grade Of Approved Shade With 4mm Thick Teak Wood Beading All-round The Edges Of Both The Tops.25mm Dia Hard Rubber Pvc Rings Shall Be Fixed To The Bottom Of All Legs Fixed With 30mm Long Screws. Finish All Wood Surfaces Shall Be French Polished With High Gloss Finish Rest All As Per Drg., Book Case Steel Dimension Over All Size Shall Be Of 840 Mm Long 310 Mm Wide And 1675 Mm High . Description All Sheet Shall Be Mild Steel Sheet 1 Mm Thick Back Sides Bottom Top And Shelves.the Book Case Shall Be Provided With Four Compartments Of Equal Size. The Shutters Of Each Compartment Shall Open Towards Top And Slide Into The Depth Of The Book Case.transparent Glass 4mm Thick Shall Be Provided To Front Shutters. Two Steel Handles Of 100 Mm Long Shall Be Provided To Each Shutter Of The Compartment. The Locking Device Shall Be Provided To Each Compartment With Duplicate Key And Each Shutter Shall Be Provided With Decorative Key Plate .make Of Lock Godrej Harrison Link Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted In Dual Colur Over A Coat Of Primer With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Left Top Corner Of Front Shutter Of Visisble Colour As Directed By Engr In Charge.rest All As Per Drgs, Desk Stand Lecture Dimension Over All Size Shall Be 970mm Wide And 1220mm High. Description Two Upright Of Mild Steel Rectangular Tube Of 75mmx25mm Of 1202mm High Shall Be Provided In Rear Side And Shall Be 635mm Apart. The Two Upright Shall Be Joinded With Bottom, Middle And Top Rails With 75mmx50mm Mild Steel Tube Of Wal Thickness 1.6mm. The Two Sides Rails At Bottom Fixed At 125mm From Bottom Shall Be 430mm Long 75mmx50mm Mild Steel Tube Of Wall Thickness 1.6mm And Shall Form The Part Of Bottom Rails And Join The Long Side Of Bottom Rail Of Size 785mm Long, . All Edges Of Pre-laminated Particle Board Remained Exposed Shall Be Covered With Teak Wood Edging As Per The Size Of Board Edging. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Given Two Coats Of Enamel Paint Over A Coat Of Primer With Spray Machine After Preparation Of Steel Surfaces And All Wooden Surfaces Shall Be Melamine Polish With Lacquer Finish As Approved By Engr In Charge.rest All As Per Drgs, Table Computer Dimension Overall Size Of Top Shall Be 900mm Long 561.20 Mm Wide And 750mm High. Description All Prelaminated Particle Board Used In Manufacturing Of Top Shelves Drawers Tray Shall Be Of 18mm Thick Prelaminated Mdf Board. The Frame Of Table Shall Be Of 25mm Square Pipe Of Wall Thickness Not Lss Than 1.6mm. The Top Of Table Shall Be Provided With 4mm Thick Teak Wood Beading.the Legs Shall Be Made Out Of 25mmx50mm Ms Rectangular Cr Pipe Of 18 Guage.each Leg Shall Be Provided With Rectangular Pvc Cover Made To Shape On Front Sides Only. The Drawers Shall Be Provided With Telescopic Channel 300mm Long.the Legs Shall Also Be Provided With Nylon Buffers .rest All As Per Drg. Finish All Wood Surfaces Shall Be French Polished With High Gloss Finish Rest All As Per Drg., Rack Pigeon Holes Steel Dimension Over All Size Shall Be Of 1905x610x915mm. Description The Entire Rack Shall Be Made Of 1mm Mild Steel Sheet.the Sides Shall Be Provided With 40x40x4mm Angle Iron Welded To 1.00mm Thick Ms Sheet.75x75x3mm Thick Flat Iron Cut To Shape Shall Be Welded At Front Corner.all Partitions Shall Also Be Made Of 1mm Thick Mild Steel Sheet And Welded To Each Other In Continous. All Dimensions, Shape And Size Shall Be Followed As Per Drg. All Joints, Fixing Shallbe Done In Accordance With Standard Specifications. Rest All As Shown On Drg. Finish All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted With Two Coats Of Silver Grey Hammer Paint Internally And Extrenally With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Top Left Side With Visible Colour. Painting Shall Be Done With Spray Machine.rest All As Per Drg., Table Plotting Executive Size 1500x750x750mm, Controller Desk, Sofa Set 3 Seater Dimension Overall Size Of The Three Seat Shall Be 1730mm Long 745mm Wide And 530mm High. Description The Set Consist Of One Long Piece Of Three Seat Only.well Seasoned Teak Wood Throughout In Frame Work Shall Be Used For Manufacturing Of Sofa.all Wood Shall Be Of First Class Teak Wood Mp Legs Of Sofa Set Shall Be 70mm X35mm In Section Teak Wood . Front Legs Shall Be Jointed By 100mm X 35mm In Section Wooden Rail In Front .front And Rear Legs Shall Be Joined With 100mm X 35mm In Section Wooden Rails In Sides.100mm Thick Cushion Of 40 Density Covered With Best Quality Tapestry Cloth Approved By Ge Not Less Than Rs 300 Meter Shall Be Provided At Seat And Back As Directed By Engr In Charge. Make Of Cushion Kurlon Sleepwell Nindiya. Finish All Wooden Surfaces Internally And Externally Shall Be Melamine Polished With High Lacquer Finish Of Walnut Shade After Properly Smoothened The Surface With Sand Emery Paper.rest All Specifications Are As Per Drg., Board Notice 2400x1220mm All Details As Per Drg. are available inside the detailed notification files. Bidders planning to target this contract in Patna should check the official portal schedule early to complete their online technical and financial submission well before the closing hours.