tender for iti veraval boq fabrication group - air compressor for plasma cutting machine , angle plate adjustable 250 x 150 x 175 , anvil 24 sq. inches working area with stand , bearing different types , boring bar indexable , caliper hermachrodite.spring 15 cm , caliper inside spring 6 inch or 15 cm , caliper outside spring 6 inch or 15 cm , caps screws m6, m8, m10, m12 , carbide wear block 1 mm-2 mm. , carrier for mounting components, , drill twist 1.5 mm to 15 mm , drills guage straight shank , cut section models for hydraulic components , cut section models for penumatic components , divider spring 6 inch or 15 cm , dowel pin straight dia. 1 inch length 4 inch , drift drill 200 mm hardened and black finish , stake grooving. 100 x 100 x 300 mm , stake hatchet with leg. 300 x 200 x 20 mm , file knife edge smooth.15o mm , file round 2nd cut 150 mm , file round 2nd cut 200 mm , file square 2nd cut 250 mm , file square rough 300 mm , file triangular 2nd cut 200 mm , marking out table 90 x 60 x 90 cm , drill gauge 1,5 to 12.5 mm in steps of 0,5 mm , drill twist st. shank metric , drill twist taper shank 8 mm to 20 mm by 0.5 mm , flange slip on forged steel flange 150nb, , gasket packing ptfe roll , gate valve dia flanged type 150nb, , gear spur old damaged to fit 50 mm shaft dia , hammer ball pein 1 kg or 2 lbs with handle , hammer chipping 0.25 kg , hammer cross pein 450 grams or 500 grams or 1 lb with handle , hammer flat head with handle , jigs and fixture sample for demonstration , key to fit shaft and pulley , marking table or surface plate table , globe valve cast iron flanged type , lapping plate 6 inch dia , mallet. dia 100 mm x 150 mm , multi angle magnetic clamp set , pipe bender spool type with stand , plastic welding machine with hot air gun, temp. display, variable temp., , swage block 5048 , cast iron 16 x 16x 16 inch , swagging and flooring tool kit , poker - 900 mm long , power cutter electrically operated , power tool for fastening capacity 10 to 18mm , pressure regulator co2 gas with flow meter , profile gauges plate type , pulleys for v-belt or flat belt , punch prick 6 inch or 15 cm , pneumatic rivet gun , screw driver insulated 6 inch or 150 mm , scriber 150 mm knurled center position , shear tinmans 300 mm , shear hand capacity to cut 6 mm thick sheet and flat , snip bent 250 mm , snip straight 300mm , standard tap screws , stop cock 25nb 2 way, threaded end , table for gas cutting suitable size , tin smiths bench folder 600 x 1.6 mm , vernier caliper set 150 inside and outside , , washer, clutch, keys, jib, cotter and circlip, air compressor for plasma cutting machine, angle plate adjustable 250 x 150 x 175, anvil 24 sq. inches working area with stand, each type of diameter 25mm (min.), with insert 1 inch shank, caliper hermachrodite.spring 15 cm, caliper inside spring 6 inch or 15 cm, caliper outside spring 6 inch or 15 cm, caps screws m6, m8, m10, m12, carbide wear block 1 mm-2 mm., such as pb and relay boxes., various sizes by 0.5 mm, letter sizes a to z with guage, wire size 1 to 60 with guage, cut section models for hydraulic components, cut section models for penumatic components, divider spring 6 inch or 15 cm, mat stainless steel, drift drill 200 mm hardened and black finish, stake grooving. 100 x 100 x 300 mm, stake hatchet with leg. 300 x 200 x 20 mm, file knife edge smooth.15o mm, file round 2nd cut 150 mm, file round 2nd cut 200 mm, file square 2nd cut 250 mm, file square rough 300 mm, file triangular 2nd cut 200 mm, marking out table 90 x 60 x 90 cm, drill gauge 1,5 to 12.5 mm in steps of 0,5 mm, 3 mm to 12 mm , in step of 0.5 mm., drill twist taper shank 8 mm to 20 mm by 0.5 mm, ansi-b16.5, class 150, gasket packing ptfe roll, class 150 flange ansi125 b16.1, gear spur old damaged to fit 50 mm shaft dia, hammer ball pein 1 kg or 2 lbs with handle, hammer chipping 0.25 kg, hammer cross pein 450 grams or 500 grams or 1 lb with handle, hammer flat head with handle, jigs and fixture sample for demonstration, key to fit shaft and pulley, 900 x 900 x 900 mm heghit, 150nb, class 150 flange ansi125 b16.1, lapping plate 6 inch dia, mallet. dia 100 mm x 150 mm, (metal base 18 x10 x 10 cm), manually operated. up to 25mm, pe,pp and pvc sheet or pipe welding control with stand. accessories, swage block 5048 , cast iron 16 x 16x 16 inch, 45 degree tubing 1/8 to 3/4 inch, poker - 900 mm long, portable abrasive cut off machine, power tool for fastening capacity 10 to 18mm, pressure regulator co2 gas with flow meter, for demonstration metric standard, to fit on 50mm dia. shaft with key slot, punch prick 6 inch or 15 cm, pneumatic rivet gun, screw driver insulated 6 inch or 150 mm, scriber 150 mm knurled center position, shear tinmans 300 mm, shear hand capacity to cut 6 mm thick sheet and flat, snip bent 250 mm, snip straight 300mm, m3, m4, m5, m6, m8, m10, m12, m14, m16, stop cock 25nb 2 way, threaded end, table for gas cutting suitable size, tin smiths bench folder 600 x 1.6 mm, depth to read inches and mm, minimum 25mm size, carbon steel material
