tender for quad copter 650 to 700 mm class frame kit , brushless motor , esc 40a, 6s , flight controller, 32-bit arm cortex- m7 class or better , propellers 15 by 5.5 inch, carbon fibre set , power distribution board , high current, 6s with bec , power module , shock absorber set , lipo battery, 6s, 8000mah , radio transmitter and receiver, 10 channel , gps and compass module m9n or equivalent , telemetry kit , wiring, connectors set , lipo battery charger, 6s, balance or multi port, 650 to 700mm class quad copter development and assembly kits, carbon fibre or glass reinforced composite quadcopter frame, 650 to 700 mm class wheelbase, fixed or foldable arm design, integrated mounting deck for flight controller, pdb and battery tray, arm wall thickness greater than or equal to 4mm carbon tube, frame weight less than or equal to 1100 to 1200 g, payload capacity greater than or equal to3kg, includes landing gear., brushless dc outrunner motor, kv rating 350 to 410kv, continuous current handling greater than or equal to 25a, max thrust greater than or equal to 1.5kg on 6s lipo with 15 inch propeller, unit weight 110g to 150g, blheli_32 (or equivalent) firmware esc, continuous current rating 40a (burst greater than or equal to 55a), input 6s lipo, 32-bit arm cortex m7 or better processor, open source autopilot firmware compatible (ardupilot/px4), integrated barometer, minimum 4 uart ports + 1 can port, microsd logging, safety switch & buzzer included, supply voltage 4.3 to 5.4v., 15 by 5.5 inch carbon fibre reinforced propellers, self locking / quick release type, factory balanced cw/ccw pair per set., pdb rated for 6s input, continuous current handling greater than or equal to 100a, integrated 5v/3a and 12v/2a bec outputs, xt60 input connector, multiple esc output pads., voltage & current sensing power module compatible with pixhawk/cube-series flight controllers, input up to 6s lipo, regulated 5.3v/3a output to fc, analog voltage/current sensing output., anti vibration rubber/silicone ball dampers for flight controller isolation, set of 4 per unit, temperature resistant, load rating suitable for 650mm to 700 mm class frame., lithium polymer battery, 6s (22.2v nominal, 25.2v fully charged), capacity 8000mah, minimum continuous discharge rate 25c, equipped with an amass xt60 main power connector with balance connector, integral over-charge/discharge protection., 2.4ghz spread spectrum radio system, minimum 10 channels, telemetry capable, control range greater than or equal to 1.5km line of sight, mode 2 configuration, ppm/sbus/ibus compatible receiver output., u blox m9n (or equivalent) gnss module with integrated magnetometer/compass, position update rate greater than or equal to 10hz, uart/i2c interface, integrated led & safety switch pad., air to ground telemetry radio pair, operating frequency 433mhz or 915mhz (region appropriate / as per applicable spectrum regulations), range greater than or equal to 1km, baud rate up to 57600bps, usb & uart interface, compatible with mission planner/ground control., xt60 connectors, silicone insulated wire (12 to 14 awg), bullet connectors (3.5/4/5.5mm), heat shrink tubing assortment, cable ties and mounting hardware kit., ac/dc input balance charger, compatible with 6s (22.2v) lipo batteries, minimum charge current 10a per port (adjustable), capable of simultaneously charging minimum 2 batteries per unit via built-in multi-port or bundled parallel-charging board, charge rate selectable up to minimum 1c for 8000mah packs, built-in balance-charging/cell-voltage monitoring, over-charge/over-discharge/short-circuit protection, lcd/display showing voltage, current and charge status, xt60-compatible output leads with balance-lead adapter.

You can fill out the integrated inquiry form below on this detail page to share your company profile. Our consultancy desk will review your query regarding power distribution board,power distribution,distribution board,battery charger,shock absorber,insulated wire,safety switch,power module,development,cable ties,batteries,battery parameters and guide you on how to coordinate efficiently with the procurement team of National Cadet Corps NCC

Tender18 provides end-to-end professional bidding support and documentation advisory for Tender For Quad Copter 650 To 700 Mm Class Frame Kit , Brushless Motor , Esc 40a, 6s , Flight Controller, 32-bit Arm Cortex- M7 Class Or Better , Propellers 15 By 5.5 Inch, Carbon Fibre Set , Power Distribution Board , High Current, 6s With Bec , Power Module , Shock Absorber Set , Lipo Battery, 6s, 8000mah , Radio Transmitter And Receiver, 10 Channel , Gps And Compass Module M9n Or Equivalent , Telemetry Kit , Wiring, Connectors Set , Lipo Battery Charger, 6s, Balance Or Multi Port, 650 To 700mm Class Quad Copter Development And Assembly Kits, Carbon Fibre Or Glass Reinforced Composite Quadcopter Frame, 650 To 700 Mm Class Wheelbase, Fixed Or Foldable Arm Design, Integrated Mounting Deck For Flight Controller, Pdb And Battery Tray, Arm Wall Thickness Greater Than Or Equal To 4mm Carbon Tube, Frame Weight Less Than Or Equal To 1100 To 1200 G, Payload Capacity Greater Than Or Equal To3kg, Includes Landing Gear., Brushless Dc Outrunner Motor, Kv Rating 350 To 410kv, Continuous Current Handling Greater Than Or Equal To 25a, Max Thrust Greater Than Or Equal To 1.5kg On 6s Lipo With 15 Inch Propeller, Unit Weight 110g To 150g, Blheli_32 (or Equivalent) Firmware Esc, Continuous Current Rating 40a (burst Greater Than Or Equal To 55a), Input 6s Lipo, 32-bit Arm Cortex M7 Or Better Processor, Open Source Autopilot Firmware Compatible (ardupilot/px4), Integrated Barometer, Minimum 4 Uart Ports + 1 Can Port, Microsd Logging, Safety Switch & Buzzer Included, Supply Voltage 4.3 To 5.4v., 15 By 5.5 Inch Carbon Fibre Reinforced Propellers, Self Locking / Quick Release Type, Factory Balanced Cw/ccw Pair Per Set., Pdb Rated For 6s Input, Continuous Current Handling Greater Than Or Equal To 100a, Integrated 5v/3a And 12v/2a Bec Outputs, Xt60 Input Connector, Multiple Esc Output Pads., Voltage & Current Sensing Power Module Compatible With Pixhawk/cube-series Flight Controllers, Input Up To 6s Lipo, Regulated 5.3v/3a Output To Fc, Analog Voltage/current Sensing Output., Anti Vibration Rubber/silicone Ball Dampers For Flight Controller Isolation, Set Of 4 Per Unit, Temperature Resistant, Load Rating Suitable For 650mm To 700 Mm Class Frame., Lithium Polymer Battery, 6s (22.2v Nominal, 25.2v Fully Charged), Capacity 8000mah, Minimum Continuous Discharge Rate 25c, Equipped With An Amass Xt60 Main Power Connector With Balance Connector, Integral Over-charge/discharge Protection., 2.4ghz Spread Spectrum Radio System, Minimum 10 Channels, Telemetry Capable, Control Range Greater Than Or Equal To 1.5km Line Of Sight, Mode 2 Configuration, Ppm/sbus/ibus Compatible Receiver Output., U Blox M9n (or Equivalent) Gnss Module With Integrated Magnetometer/compass, Position Update Rate Greater Than Or Equal To 10hz, Uart/i2c Interface, Integrated Led & Safety Switch Pad., Air To Ground Telemetry Radio Pair, Operating Frequency 433mhz Or 915mhz (region Appropriate / As Per Applicable Spectrum Regulations), Range Greater Than Or Equal To 1km, Baud Rate Up To 57600bps, Usb & Uart Interface, Compatible With Mission Planner/ground Control., Xt60 Connectors, Silicone Insulated Wire (12 To 14 Awg), Bullet Connectors (3.5/4/5.5mm), Heat Shrink Tubing Assortment, Cable Ties And Mounting Hardware Kit., Ac/dc Input Balance Charger, Compatible With 6s (22.2v) Lipo Batteries, Minimum Charge Current 10a Per Port (adjustable), Capable Of Simultaneously Charging Minimum 2 Batteries Per Unit Via Built-in Multi-port Or Bundled Parallel-charging Board, Charge Rate Selectable Up To Minimum 1c For 8000mah Packs, Built-in Balance-charging/cell-voltage Monitoring, Over-charge/over-discharge/short-circuit Protection, Lcd/display Showing Voltage, Current And Charge Status, Xt60-compatible Output Leads With Balance-lead Adapter. . Our senior analysts help you decode the complete project guidelines, manage accurate costing sheets, and complete error-free submissions on the official platform used by National Cadet Corps NCC.

Most online bids face rejection during the initial evaluation round due to avoidable errors like uploading blurred document scans, submitting expired DSCs, or missing critical experience papers required for Tender For Quad Copter 650 To 700 Mm Class Frame Kit , Brushless Motor , Esc 40a, 6s , Flight Controller, 32-bit Arm Cortex- M7 Class Or Better , Propellers 15 By 5.5 Inch, Carbon Fibre Set , Power Distribution Board , High Current, 6s With Bec , Power Module , Shock Absorber Set , Lipo Battery, 6s, 8000mah , Radio Transmitter And Receiver, 10 Channel , Gps And Compass Module M9n Or Equivalent , Telemetry Kit , Wiring, Connectors Set , Lipo Battery Charger, 6s, Balance Or Multi Port, 650 To 700mm Class Quad Copter Development And Assembly Kits, Carbon Fibre Or Glass Reinforced Composite Quadcopter Frame, 650 To 700 Mm Class Wheelbase, Fixed Or Foldable Arm Design, Integrated Mounting Deck For Flight Controller, Pdb And Battery Tray, Arm Wall Thickness Greater Than Or Equal To 4mm Carbon Tube, Frame Weight Less Than Or Equal To 1100 To 1200 G, Payload Capacity Greater Than Or Equal To3kg, Includes Landing Gear., Brushless Dc Outrunner Motor, Kv Rating 350 To 410kv, Continuous Current Handling Greater Than Or Equal To 25a, Max Thrust Greater Than Or Equal To 1.5kg On 6s Lipo With 15 Inch Propeller, Unit Weight 110g To 150g, Blheli_32 (or Equivalent) Firmware Esc, Continuous Current Rating 40a (burst Greater Than Or Equal To 55a), Input 6s Lipo, 32-bit Arm Cortex M7 Or Better Processor, Open Source Autopilot Firmware Compatible (ardupilot/px4), Integrated Barometer, Minimum 4 Uart Ports + 1 Can Port, Microsd Logging, Safety Switch & Buzzer Included, Supply Voltage 4.3 To 5.4v., 15 By 5.5 Inch Carbon Fibre Reinforced Propellers, Self Locking / Quick Release Type, Factory Balanced Cw/ccw Pair Per Set., Pdb Rated For 6s Input, Continuous Current Handling Greater Than Or Equal To 100a, Integrated 5v/3a And 12v/2a Bec Outputs, Xt60 Input Connector, Multiple Esc Output Pads., Voltage & Current Sensing Power Module Compatible With Pixhawk/cube-series Flight Controllers, Input Up To 6s Lipo, Regulated 5.3v/3a Output To Fc, Analog Voltage/current Sensing Output., Anti Vibration Rubber/silicone Ball Dampers For Flight Controller Isolation, Set Of 4 Per Unit, Temperature Resistant, Load Rating Suitable For 650mm To 700 Mm Class Frame., Lithium Polymer Battery, 6s (22.2v Nominal, 25.2v Fully Charged), Capacity 8000mah, Minimum Continuous Discharge Rate 25c, Equipped With An Amass Xt60 Main Power Connector With Balance Connector, Integral Over-charge/discharge Protection., 2.4ghz Spread Spectrum Radio System, Minimum 10 Channels, Telemetry Capable, Control Range Greater Than Or Equal To 1.5km Line Of Sight, Mode 2 Configuration, Ppm/sbus/ibus Compatible Receiver Output., U Blox M9n (or Equivalent) Gnss Module With Integrated Magnetometer/compass, Position Update Rate Greater Than Or Equal To 10hz, Uart/i2c Interface, Integrated Led & Safety Switch Pad., Air To Ground Telemetry Radio Pair, Operating Frequency 433mhz Or 915mhz (region Appropriate / As Per Applicable Spectrum Regulations), Range Greater Than Or Equal To 1km, Baud Rate Up To 57600bps, Usb & Uart Interface, Compatible With Mission Planner/ground Control., Xt60 Connectors, Silicone Insulated Wire (12 To 14 Awg), Bullet Connectors (3.5/4/5.5mm), Heat Shrink Tubing Assortment, Cable Ties And Mounting Hardware Kit., Ac/dc Input Balance Charger, Compatible With 6s (22.2v) Lipo Batteries, Minimum Charge Current 10a Per Port (adjustable), Capable Of Simultaneously Charging Minimum 2 Batteries Per Unit Via Built-in Multi-port Or Bundled Parallel-charging Board, Charge Rate Selectable Up To Minimum 1c For 8000mah Packs, Built-in Balance-charging/cell-voltage Monitoring, Over-charge/over-discharge/short-circuit Protection, Lcd/display Showing Voltage, Current And Charge Status, Xt60-compatible Output Leads With Balance-lead Adapter. in Kerala.

Eligibility for outstation bidders depends entirely on the terms set inside the document for Tender For Quad Copter 650 To 700 Mm Class Frame Kit , Brushless Motor , Esc 40a, 6s , Flight Controller, 32-bit Arm Cortex- M7 Class Or Better , Propellers 15 By 5.5 Inch, Carbon Fibre Set , Power Distribution Board , High Current, 6s With Bec , Power Module , Shock Absorber Set , Lipo Battery, 6s, 8000mah , Radio Transmitter And Receiver, 10 Channel , Gps And Compass Module M9n Or Equivalent , Telemetry Kit , Wiring, Connectors Set , Lipo Battery Charger, 6s, Balance Or Multi Port, 650 To 700mm Class Quad Copter Development And Assembly Kits, Carbon Fibre Or Glass Reinforced Composite Quadcopter Frame, 650 To 700 Mm Class Wheelbase, Fixed Or Foldable Arm Design, Integrated Mounting Deck For Flight Controller, Pdb And Battery Tray, Arm Wall Thickness Greater Than Or Equal To 4mm Carbon Tube, Frame Weight Less Than Or Equal To 1100 To 1200 G, Payload Capacity Greater Than Or Equal To3kg, Includes Landing Gear., Brushless Dc Outrunner Motor, Kv Rating 350 To 410kv, Continuous Current Handling Greater Than Or Equal To 25a, Max Thrust Greater Than Or Equal To 1.5kg On 6s Lipo With 15 Inch Propeller, Unit Weight 110g To 150g, Blheli_32 (or Equivalent) Firmware Esc, Continuous Current Rating 40a (burst Greater Than Or Equal To 55a), Input 6s Lipo, 32-bit Arm Cortex M7 Or Better Processor, Open Source Autopilot Firmware Compatible (ardupilot/px4), Integrated Barometer, Minimum 4 Uart Ports + 1 Can Port, Microsd Logging, Safety Switch & Buzzer Included, Supply Voltage 4.3 To 5.4v., 15 By 5.5 Inch Carbon Fibre Reinforced Propellers, Self Locking / Quick Release Type, Factory Balanced Cw/ccw Pair Per Set., Pdb Rated For 6s Input, Continuous Current Handling Greater Than Or Equal To 100a, Integrated 5v/3a And 12v/2a Bec Outputs, Xt60 Input Connector, Multiple Esc Output Pads., Voltage & Current Sensing Power Module Compatible With Pixhawk/cube-series Flight Controllers, Input Up To 6s Lipo, Regulated 5.3v/3a Output To Fc, Analog Voltage/current Sensing Output., Anti Vibration Rubber/silicone Ball Dampers For Flight Controller Isolation, Set Of 4 Per Unit, Temperature Resistant, Load Rating Suitable For 650mm To 700 Mm Class Frame., Lithium Polymer Battery, 6s (22.2v Nominal, 25.2v Fully Charged), Capacity 8000mah, Minimum Continuous Discharge Rate 25c, Equipped With An Amass Xt60 Main Power Connector With Balance Connector, Integral Over-charge/discharge Protection., 2.4ghz Spread Spectrum Radio System, Minimum 10 Channels, Telemetry Capable, Control Range Greater Than Or Equal To 1.5km Line Of Sight, Mode 2 Configuration, Ppm/sbus/ibus Compatible Receiver Output., U Blox M9n (or Equivalent) Gnss Module With Integrated Magnetometer/compass, Position Update Rate Greater Than Or Equal To 10hz, Uart/i2c Interface, Integrated Led & Safety Switch Pad., Air To Ground Telemetry Radio Pair, Operating Frequency 433mhz Or 915mhz (region Appropriate / As Per Applicable Spectrum Regulations), Range Greater Than Or Equal To 1km, Baud Rate Up To 57600bps, Usb & Uart Interface, Compatible With Mission Planner/ground Control., Xt60 Connectors, Silicone Insulated Wire (12 To 14 Awg), Bullet Connectors (3.5/4/5.5mm), Heat Shrink Tubing Assortment, Cable Ties And Mounting Hardware Kit., Ac/dc Input Balance Charger, Compatible With 6s (22.2v) Lipo Batteries, Minimum Charge Current 10a Per Port (adjustable), Capable Of Simultaneously Charging Minimum 2 Batteries Per Unit Via Built-in Multi-port Or Bundled Parallel-charging Board, Charge Rate Selectable Up To Minimum 1c For 8000mah Packs, Built-in Balance-charging/cell-voltage Monitoring, Over-charge/over-discharge/short-circuit Protection, Lcd/display Showing Voltage, Current And Charge Status, Xt60-compatible Output Leads With Balance-lead Adapter.. While many public sector projects allow national competitive bidding, certain localized works require local offices or specific registration metrics in Kollam.

If this procurement is routed through the central marketplace, an active GeM Seller ID is mandatory to supply power distribution board,power distribution,distribution board,battery charger,shock absorber,insulated wire,safety switch,power module,development,cable ties,batteries,battery items. Tender18 offers complete assistance for brand cataloging, profile creation, and vendor assessment required officially by National Cadet Corps NCC

To register an eligible bid for these power distribution board,power distribution,distribution board,battery charger,shock absorber,insulated wire,safety switch,power module,development,cable ties,batteries,battery contracts, companies must prepare their core compliance documents. Vendors operating across Kerala must ensure they possess a valid GST registration, permanent account number (PAN), and active Class-3 Digital Signature Certificates.

This public procurement cycle is specifically looking for qualified vendors and suppliers who can provide high-quality power distribution board,power distribution,distribution board,battery charger,shock absorber,insulated wire,safety switch,power module,development,cable ties,batteries,battery solutions. The operational execution, delivery, and deployment of these materials must be managed locally within the Kollam region.

The estimated project cost and budget thresholds can be reviewed directly inside the tender document. Bidders can analyze these qualification files to check if their firm meets the financial capability criteria specified for Tender For Quad Copter 650 To 700 Mm Class Frame Kit , Brushless Motor , Esc 40a, 6s , Flight Controller, 32-bit Arm Cortex- M7 Class Or Better , Propellers 15 By 5.5 Inch, Carbon Fibre Set , Power Distribution Board , High Current, 6s With Bec , Power Module , Shock Absorber Set , Lipo Battery, 6s, 8000mah , Radio Transmitter And Receiver, 10 Channel , Gps And Compass Module M9n Or Equivalent , Telemetry Kit , Wiring, Connectors Set , Lipo Battery Charger, 6s, Balance Or Multi Port, 650 To 700mm Class Quad Copter Development And Assembly Kits, Carbon Fibre Or Glass Reinforced Composite Quadcopter Frame, 650 To 700 Mm Class Wheelbase, Fixed Or Foldable Arm Design, Integrated Mounting Deck For Flight Controller, Pdb And Battery Tray, Arm Wall Thickness Greater Than Or Equal To 4mm Carbon Tube, Frame Weight Less Than Or Equal To 1100 To 1200 G, Payload Capacity Greater Than Or Equal To3kg, Includes Landing Gear., Brushless Dc Outrunner Motor, Kv Rating 350 To 410kv, Continuous Current Handling Greater Than Or Equal To 25a, Max Thrust Greater Than Or Equal To 1.5kg On 6s Lipo With 15 Inch Propeller, Unit Weight 110g To 150g, Blheli_32 (or Equivalent) Firmware Esc, Continuous Current Rating 40a (burst Greater Than Or Equal To 55a), Input 6s Lipo, 32-bit Arm Cortex M7 Or Better Processor, Open Source Autopilot Firmware Compatible (ardupilot/px4), Integrated Barometer, Minimum 4 Uart Ports + 1 Can Port, Microsd Logging, Safety Switch & Buzzer Included, Supply Voltage 4.3 To 5.4v., 15 By 5.5 Inch Carbon Fibre Reinforced Propellers, Self Locking / Quick Release Type, Factory Balanced Cw/ccw Pair Per Set., Pdb Rated For 6s Input, Continuous Current Handling Greater Than Or Equal To 100a, Integrated 5v/3a And 12v/2a Bec Outputs, Xt60 Input Connector, Multiple Esc Output Pads., Voltage & Current Sensing Power Module Compatible With Pixhawk/cube-series Flight Controllers, Input Up To 6s Lipo, Regulated 5.3v/3a Output To Fc, Analog Voltage/current Sensing Output., Anti Vibration Rubber/silicone Ball Dampers For Flight Controller Isolation, Set Of 4 Per Unit, Temperature Resistant, Load Rating Suitable For 650mm To 700 Mm Class Frame., Lithium Polymer Battery, 6s (22.2v Nominal, 25.2v Fully Charged), Capacity 8000mah, Minimum Continuous Discharge Rate 25c, Equipped With An Amass Xt60 Main Power Connector With Balance Connector, Integral Over-charge/discharge Protection., 2.4ghz Spread Spectrum Radio System, Minimum 10 Channels, Telemetry Capable, Control Range Greater Than Or Equal To 1.5km Line Of Sight, Mode 2 Configuration, Ppm/sbus/ibus Compatible Receiver Output., U Blox M9n (or Equivalent) Gnss Module With Integrated Magnetometer/compass, Position Update Rate Greater Than Or Equal To 10hz, Uart/i2c Interface, Integrated Led & Safety Switch Pad., Air To Ground Telemetry Radio Pair, Operating Frequency 433mhz Or 915mhz (region Appropriate / As Per Applicable Spectrum Regulations), Range Greater Than Or Equal To 1km, Baud Rate Up To 57600bps, Usb & Uart Interface, Compatible With Mission Planner/ground Control., Xt60 Connectors, Silicone Insulated Wire (12 To 14 Awg), Bullet Connectors (3.5/4/5.5mm), Heat Shrink Tubing Assortment, Cable Ties And Mounting Hardware Kit., Ac/dc Input Balance Charger, Compatible With 6s (22.2v) Lipo Batteries, Minimum Charge Current 10a Per Port (adjustable), Capable Of Simultaneously Charging Minimum 2 Batteries Per Unit Via Built-in Multi-port Or Bundled Parallel-charging Board, Charge Rate Selectable Up To Minimum 1c For 8000mah Packs, Built-in Balance-charging/cell-voltage Monitoring, Over-charge/over-discharge/short-circuit Protection, Lcd/display Showing Voltage, Current And Charge Status, Xt60-compatible Output Leads With Balance-lead Adapter. by National Cadet Corps NCC

You can download the commercial Bill of Quantities (BOQ) spreadsheet directly using the secure link provided on this page. The BOQ file contains the item descriptions and rate filling forms officially validated for Tender For Quad Copter 650 To 700 Mm Class Frame Kit , Brushless Motor , Esc 40a, 6s , Flight Controller, 32-bit Arm Cortex- M7 Class Or Better , Propellers 15 By 5.5 Inch, Carbon Fibre Set , Power Distribution Board , High Current, 6s With Bec , Power Module , Shock Absorber Set , Lipo Battery, 6s, 8000mah , Radio Transmitter And Receiver, 10 Channel , Gps And Compass Module M9n Or Equivalent , Telemetry Kit , Wiring, Connectors Set , Lipo Battery Charger, 6s, Balance Or Multi Port, 650 To 700mm Class Quad Copter Development And Assembly Kits, Carbon Fibre Or Glass Reinforced Composite Quadcopter Frame, 650 To 700 Mm Class Wheelbase, Fixed Or Foldable Arm Design, Integrated Mounting Deck For Flight Controller, Pdb And Battery Tray, Arm Wall Thickness Greater Than Or Equal To 4mm Carbon Tube, Frame Weight Less Than Or Equal To 1100 To 1200 G, Payload Capacity Greater Than Or Equal To3kg, Includes Landing Gear., Brushless Dc Outrunner Motor, Kv Rating 350 To 410kv, Continuous Current Handling Greater Than Or Equal To 25a, Max Thrust Greater Than Or Equal To 1.5kg On 6s Lipo With 15 Inch Propeller, Unit Weight 110g To 150g, Blheli_32 (or Equivalent) Firmware Esc, Continuous Current Rating 40a (burst Greater Than Or Equal To 55a), Input 6s Lipo, 32-bit Arm Cortex M7 Or Better Processor, Open Source Autopilot Firmware Compatible (ardupilot/px4), Integrated Barometer, Minimum 4 Uart Ports + 1 Can Port, Microsd Logging, Safety Switch & Buzzer Included, Supply Voltage 4.3 To 5.4v., 15 By 5.5 Inch Carbon Fibre Reinforced Propellers, Self Locking / Quick Release Type, Factory Balanced Cw/ccw Pair Per Set., Pdb Rated For 6s Input, Continuous Current Handling Greater Than Or Equal To 100a, Integrated 5v/3a And 12v/2a Bec Outputs, Xt60 Input Connector, Multiple Esc Output Pads., Voltage & Current Sensing Power Module Compatible With Pixhawk/cube-series Flight Controllers, Input Up To 6s Lipo, Regulated 5.3v/3a Output To Fc, Analog Voltage/current Sensing Output., Anti Vibration Rubber/silicone Ball Dampers For Flight Controller Isolation, Set Of 4 Per Unit, Temperature Resistant, Load Rating Suitable For 650mm To 700 Mm Class Frame., Lithium Polymer Battery, 6s (22.2v Nominal, 25.2v Fully Charged), Capacity 8000mah, Minimum Continuous Discharge Rate 25c, Equipped With An Amass Xt60 Main Power Connector With Balance Connector, Integral Over-charge/discharge Protection., 2.4ghz Spread Spectrum Radio System, Minimum 10 Channels, Telemetry Capable, Control Range Greater Than Or Equal To 1.5km Line Of Sight, Mode 2 Configuration, Ppm/sbus/ibus Compatible Receiver Output., U Blox M9n (or Equivalent) Gnss Module With Integrated Magnetometer/compass, Position Update Rate Greater Than Or Equal To 10hz, Uart/i2c Interface, Integrated Led & Safety Switch Pad., Air To Ground Telemetry Radio Pair, Operating Frequency 433mhz Or 915mhz (region Appropriate / As Per Applicable Spectrum Regulations), Range Greater Than Or Equal To 1km, Baud Rate Up To 57600bps, Usb & Uart Interface, Compatible With Mission Planner/ground Control., Xt60 Connectors, Silicone Insulated Wire (12 To 14 Awg), Bullet Connectors (3.5/4/5.5mm), Heat Shrink Tubing Assortment, Cable Ties And Mounting Hardware Kit., Ac/dc Input Balance Charger, Compatible With 6s (22.2v) Lipo Batteries, Minimum Charge Current 10a Per Port (adjustable), Capable Of Simultaneously Charging Minimum 2 Batteries Per Unit Via Built-in Multi-port Or Bundled Parallel-charging Board, Charge Rate Selectable Up To Minimum 1c For 8000mah Packs, Built-in Balance-charging/cell-voltage Monitoring, Over-charge/over-discharge/short-circuit Protection, Lcd/display Showing Voltage, Current And Charge Status, Xt60-compatible Output Leads With Balance-lead Adapter. within the Kerala jurisdiction

The official timeline and deadline details for Tender For Quad Copter 650 To 700 Mm Class Frame Kit , Brushless Motor , Esc 40a, 6s , Flight Controller, 32-bit Arm Cortex- M7 Class Or Better , Propellers 15 By 5.5 Inch, Carbon Fibre Set , Power Distribution Board , High Current, 6s With Bec , Power Module , Shock Absorber Set , Lipo Battery, 6s, 8000mah , Radio Transmitter And Receiver, 10 Channel , Gps And Compass Module M9n Or Equivalent , Telemetry Kit , Wiring, Connectors Set , Lipo Battery Charger, 6s, Balance Or Multi Port, 650 To 700mm Class Quad Copter Development And Assembly Kits, Carbon Fibre Or Glass Reinforced Composite Quadcopter Frame, 650 To 700 Mm Class Wheelbase, Fixed Or Foldable Arm Design, Integrated Mounting Deck For Flight Controller, Pdb And Battery Tray, Arm Wall Thickness Greater Than Or Equal To 4mm Carbon Tube, Frame Weight Less Than Or Equal To 1100 To 1200 G, Payload Capacity Greater Than Or Equal To3kg, Includes Landing Gear., Brushless Dc Outrunner Motor, Kv Rating 350 To 410kv, Continuous Current Handling Greater Than Or Equal To 25a, Max Thrust Greater Than Or Equal To 1.5kg On 6s Lipo With 15 Inch Propeller, Unit Weight 110g To 150g, Blheli_32 (or Equivalent) Firmware Esc, Continuous Current Rating 40a (burst Greater Than Or Equal To 55a), Input 6s Lipo, 32-bit Arm Cortex M7 Or Better Processor, Open Source Autopilot Firmware Compatible (ardupilot/px4), Integrated Barometer, Minimum 4 Uart Ports + 1 Can Port, Microsd Logging, Safety Switch & Buzzer Included, Supply Voltage 4.3 To 5.4v., 15 By 5.5 Inch Carbon Fibre Reinforced Propellers, Self Locking / Quick Release Type, Factory Balanced Cw/ccw Pair Per Set., Pdb Rated For 6s Input, Continuous Current Handling Greater Than Or Equal To 100a, Integrated 5v/3a And 12v/2a Bec Outputs, Xt60 Input Connector, Multiple Esc Output Pads., Voltage & Current Sensing Power Module Compatible With Pixhawk/cube-series Flight Controllers, Input Up To 6s Lipo, Regulated 5.3v/3a Output To Fc, Analog Voltage/current Sensing Output., Anti Vibration Rubber/silicone Ball Dampers For Flight Controller Isolation, Set Of 4 Per Unit, Temperature Resistant, Load Rating Suitable For 650mm To 700 Mm Class Frame., Lithium Polymer Battery, 6s (22.2v Nominal, 25.2v Fully Charged), Capacity 8000mah, Minimum Continuous Discharge Rate 25c, Equipped With An Amass Xt60 Main Power Connector With Balance Connector, Integral Over-charge/discharge Protection., 2.4ghz Spread Spectrum Radio System, Minimum 10 Channels, Telemetry Capable, Control Range Greater Than Or Equal To 1.5km Line Of Sight, Mode 2 Configuration, Ppm/sbus/ibus Compatible Receiver Output., U Blox M9n (or Equivalent) Gnss Module With Integrated Magnetometer/compass, Position Update Rate Greater Than Or Equal To 10hz, Uart/i2c Interface, Integrated Led & Safety Switch Pad., Air To Ground Telemetry Radio Pair, Operating Frequency 433mhz Or 915mhz (region Appropriate / As Per Applicable Spectrum Regulations), Range Greater Than Or Equal To 1km, Baud Rate Up To 57600bps, Usb & Uart Interface, Compatible With Mission Planner/ground Control., Xt60 Connectors, Silicone Insulated Wire (12 To 14 Awg), Bullet Connectors (3.5/4/5.5mm), Heat Shrink Tubing Assortment, Cable Ties And Mounting Hardware Kit., Ac/dc Input Balance Charger, Compatible With 6s (22.2v) Lipo Batteries, Minimum Charge Current 10a Per Port (adjustable), Capable Of Simultaneously Charging Minimum 2 Batteries Per Unit Via Built-in Multi-port Or Bundled Parallel-charging Board, Charge Rate Selectable Up To Minimum 1c For 8000mah Packs, Built-in Balance-charging/cell-voltage Monitoring, Over-charge/over-discharge/short-circuit Protection, Lcd/display Showing Voltage, Current And Charge Status, Xt60-compatible Output Leads With Balance-lead Adapter. are available inside the detailed notification files. Bidders planning to target this contract in Kollam should check the official portal schedule early to complete their online technical and financial submission well before the closing hours.