tender for tools equipment solar technician trade toolkit , equipment , toolkit-equipment , equipment attachment , safety tool , equipment furniture, screw driver insulated /150 mm, screw driver insulated plastic handle 5 mm tip length 200 mm, screw driver electrician 250 mm thin stem insulated handle magnetic point, knife double bladed electrician 100 mm, rule steel 30 cm graduated both english and metric units, hammer cross pein 220 grams / 250 grams / 0.5 lb with handle., electrical symbol and accessories chart, vice hand 50 mm jaw, hacksaw frame fixed type 150 mm, plier round nose, 4/100 mm, guage- wire imperial standard, crimping tool for crimping 16 sq mm to 95 sq.mm, square engineers 6/ 15 cm blade, multi meter (analog) 0 to 1000 m ohms, 2v to 500 v,100 microa to 10a dc and ac, load bank (variable) up to 1.2 kw ( lamp / heater type), earth gi plate 60cm x 60cm x 6mm, earth electrode secondary cu strip 20x5mm, tap set metric 2 to 10 mm (set of 9 pcs) with wrench, hand trolley with 4 wheels 500mm x 750 mm, rooftop mounting structure for 4 x 250 w solar panels mounting practice, with tilt adjustment, protective relays and contactors rack suitable for practice of control circuits using banana plugs and sockets, cables twisted pair nonmetallic sheathed cable underground feeder cable ribbon cable metallic sheathed cable multi-conductor cable coaxial cable direct-buried cable 1 mtr each, bolts, nuts, anchor bolts, washers, screws, other pins, lugs, megger 500 volts cum continuity tester/insulation tester, solar insulation meter, magnetic flux meter 0-500 tesla, tong tester ( 0 - 100 a multi range ), soldering iron exchangable copper tip 65 watt, battery charger 0 - 6 - 9 - 12 - 24 - 48 v, 30amp, solar charge controller with dusk to dawn automatic switching 12v, 10a, solar charge controller with manual switch ( day lighting) 12 v 10 a, solar lantern cfl type, solar lantern assembly sets, solar cell kit, clinometer for angle measurement, level spirit for floor level check, dc table fan 12v, a.c. voltmeter m.i. 0-500 v, voltmeter (0-30v) (table model), voltmeter (0-100v) (table model), ampere meter 0 to 1 amp. (dc), ammeter m.c.0-5 d.c, ammeter m.c. 0-20 a centre zero, ammeter m.c. 0-50 a centre zero, single phase power factor meter, rheostat 0-1 ohms, rheostat 0-10 ohms 5 amp, rheostat 0-25 ohms 1 amp, rheostat 0-300 ohms 5 amp, a.c. energy meter (single phase 10 amp. 240 v), energy meter 3 ph 440 v,15 a, 4 wire, kilo watt (kw) meter analog 0-1.5-3kw, pressure coil rating- 240v/440v, current rating-5a/10a analog, portable type housed in bakelite case, watt meter (digital), phase sequence tester., frequency meter 45 to 55 hz, led lights 12 v dc, led lights 6 v dc, rubber gloves pair, gloves cotton, gum boots, safety goggles/ glass (plastic or fiber), wiring board on stand 3 meters x 1meter with 0.5 meter projection on the top

Latest Tender Detail from department of employment and training DET for the tender for tools equipment solar technician trade toolkit , equipment , toolkit-equipment , equipment attachment , safety tool , equipment furniture, screw driver insulated /150 mm, screw driver insulated plastic handle 5 mm tip length 200 mm, screw driver electrician 250 mm thin stem insulated handle magnetic point, knife double bladed electrician 100 mm, rule steel 30 cm graduated both english and metric units, hammer cross pein 220 grams / 250 grams / 0.5 lb with handle., electrical symbol and accessories chart, vice hand 50 mm jaw, hacksaw frame fixed type 150 mm, plier round nose, 4/100 mm, guage- wire imperial standard, crimping tool for crimping 16 sq mm to 95 sq.mm, square engineers 6/ 15 cm blade, multi meter (analog) 0 to 1000 m ohms, 2v to 500 v,100 microa to 10a dc and ac, load bank (variable) up to 1.2 kw ( lamp / heater type), earth gi plate 60cm x 60cm x 6mm, earth electrode secondary cu strip 20x5mm, tap set metric 2 to 10 mm (set of 9 pcs) with wrench, hand trolley with 4 wheels 500mm x 750 mm, rooftop mounting structure for 4 x 250 w solar panels mounting practice, with tilt adjustment, protective relays and contactors rack suitable for practice of control circuits using banana plugs and sockets, cables twisted pair nonmetallic sheathed cable underground feeder cable ribbon cable metallic sheathed cable multi-conductor cable coaxial cable direct-buried cable 1 mtr each, bolts, nuts, anchor bolts, washers, screws, other pins, lugs, megger 500 volts cum continuity tester/insulation tester, solar insulation meter, magnetic flux meter 0-500 tesla, tong tester ( 0 - 100 a multi range ), soldering iron exchangable copper tip 65 watt, battery charger 0 - 6 - 9 - 12 - 24 - 48 v, 30amp, solar charge controller with dusk to dawn automatic switching 12v, 10a, solar charge controller with manual switch ( day lighting) 12 v 10 a, solar lantern cfl type, solar lantern assembly sets, solar cell kit, clinometer for angle measurement, level spirit for floor level check, dc table fan 12v, a.c. voltmeter m.i. 0-500 v, voltmeter (0-30v) (table model), voltmeter (0-100v) (table model), ampere meter 0 to 1 amp. (dc), ammeter m.c.0-5 d.c, ammeter m.c. 0-20 a centre zero, ammeter m.c. 0-50 a centre zero, single phase power factor meter, rheostat 0-1 ohms, rheostat 0-10 ohms 5 amp, rheostat 0-25 ohms 1 amp, rheostat 0-300 ohms 5 amp, a.c. energy meter (single phase 10 amp. 240 v), energy meter 3 ph 440 v,15 a, 4 wire, kilo watt (kw) meter analog 0-1.5-3kw, pressure coil rating- 240v/440v, current rating-5a/10a analog, portable type housed in bakelite case, watt meter (digital), phase sequence tester., frequency meter 45 to 55 hz, led lights 12 v dc, led lights 6 v dc, rubber gloves pair, gloves cotton, gum boots, safety goggles/ glass (plastic or fiber), wiring board on stand 3 meters x 1meter with 0.5 meter projection on the top in umarpada, gujarat,. Reference number 16257808. Don't miss out on this chance to be part of a significant project. Register for free today to access the complete tender details and download the necessary documents. Seize the opportunity with Tender 18!

T18 Ref No:16257808Tender Value:Refer Document
Tender ID:GEM/2026/B/7758969Tender EMD:Refer Document
Tender Agency:department of employment and training DETTender Fee:Refer Document
City:umarpadaPublished Date:Jul 14, 2026
State:gujaratDue Date:Jul 29, 2026
Tender Related Keywords :solar charge controller, power factor meter, insulation tester, earth electrode, conductor cable, battery charger, frequency meter, plastic handle, sheathed cable, soldering iron, safety goggles, hacksaw frame, crimping tool, coaxial cable, solar lantern, rubber gloves, screw driver, solar panels, feeder cable, ribbon cable, ac voltmeter, ampere meter, power factor, energy meter, safety tool, solar cell, watt meter, led lights, load bank, table fan, gum boots, battery, boltsTender Opening Date:Jul 29, 2026
Description :total quantity = 232

Get Complete Tender Documents to Participate

Tender NoticeBOQEligibilityEMD DetailsImportant Dates
We take all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Browse GeM Portal Tenders

This Government Tender has been Published  by Department Of Employment And Training DET for work related to solar charge controller,power factor meter,insulation tester,earth electrode,conductor cable,battery charger,frequency meter,plastic handle,sheathed cable,soldering iron,safety goggles,hacksaw frame,crimping tool,coaxial cable,solar lantern,rubber gloves,screw driver,solar panels,feeder cable,ribbon cable,ac voltmeter,ampere meter,power factor,energy meter,safety tool,solar cell,watt meter,led lights,load bank,table fan,gum boots,battery,bolts in Umarpada, Gujarat. The Tender work is tender for tools equipment solar technician trade toolkit , equipment , toolkit-equipment , equipment attachment , safety tool , equipment furniture, screw driver insulated /150 mm, screw driver insulated plastic handle 5 mm tip length 200 mm, screw driver electrician 250 mm thin stem insulated handle magnetic point, knife double bladed electrician 100 mm, rule steel 30 cm graduated both english and metric units, hammer cross pein 220 grams / 250 grams / 0.5 lb with handle., electrical symbol and accessories chart, vice hand 50 mm jaw, hacksaw frame fixed type 150 mm, plier round nose, 4/100 mm, guage- wire imperial standard, crimping tool for crimping 16 sq mm to 95 sq.mm, square engineers 6/ 15 cm blade, multi meter (analog) 0 to 1000 m ohms, 2v to 500 v,100 microa to 10a dc and ac, load bank (variable) up to 1.2 kw ( lamp / heater type), earth gi plate 60cm x 60cm x 6mm, earth electrode secondary cu strip 20x5mm, tap set metric 2 to 10 mm (set of 9 pcs) with wrench, hand trolley with 4 wheels 500mm x 750 mm, rooftop mounting structure for 4 x 250 w solar panels mounting practice, with tilt adjustment, protective relays and contactors rack suitable for practice of control circuits using banana plugs and sockets, cables twisted pair nonmetallic sheathed cable underground feeder cable ribbon cable metallic sheathed cable multi-conductor cable coaxial cable direct-buried cable 1 mtr each, bolts, nuts, anchor bolts, washers, screws, other pins, lugs, megger 500 volts cum continuity tester/insulation tester, solar insulation meter, magnetic flux meter 0-500 tesla, tong tester ( 0 - 100 a multi range ), soldering iron exchangable copper tip 65 watt, battery charger 0 - 6 - 9 - 12 - 24 - 48 v, 30amp, solar charge controller with dusk to dawn automatic switching 12v, 10a, solar charge controller with manual switch ( day lighting) 12 v 10 a, solar lantern cfl type, solar lantern assembly sets, solar cell kit, clinometer for angle measurement, level spirit for floor level check, dc table fan 12v, a.c. voltmeter m.i. 0-500 v, voltmeter (0-30v) (table model), voltmeter (0-100v) (table model), ampere meter 0 to 1 amp. (dc), ammeter m.c.0-5 d.c, ammeter m.c. 0-20 a centre zero, ammeter m.c. 0-50 a centre zero, single phase power factor meter, rheostat 0-1 ohms, rheostat 0-10 ohms 5 amp, rheostat 0-25 ohms 1 amp, rheostat 0-300 ohms 5 amp, a.c. energy meter (single phase 10 amp. 240 v), energy meter 3 ph 440 v,15 a, 4 wire, kilo watt (kw) meter analog 0-1.5-3kw, pressure coil rating- 240v/440v, current rating-5a/10a analog, portable type housed in bakelite case, watt meter (digital), phase sequence tester., frequency meter 45 to 55 hz, led lights 12 v dc, led lights 6 v dc, rubber gloves pair, gloves cotton, gum boots, safety goggles/ glass (plastic or fiber), wiring board on stand 3 meters x 1meter with 0.5 meter projection on the top. Tender18 Provide this type Government Tender Information on daily basis.


This tender invites eligible contractors, suppliers, manufacturers, consultants, Startups, Msmes, traders and service providers to submit bids for the specified project, supply, service, or work requirement.


Before applying, interested bidders should review the tender scope, eligibility criteria, estimated contract value, important dates, technical requirements, reqired docuent list for bidder and bid submission instructions as per provided in the official tender documents. 


This Verified Information Provide By Tender18 in this page so Bidder Can Easiy  Understanding tender  requirements and bidders can prepare a compliant and competitive tender proposal.

To participate in the tender for tools equipment solar technician trade toolkit , equipment , toolkit-equipment , equipment attachment , safety tool , equipment furniture, screw driver insulated /150 mm, screw driver insulated plastic handle 5 mm tip length 200 mm, screw driver electrician 250 mm thin stem insulated handle magnetic point, knife double bladed electrician 100 mm, rule steel 30 cm graduated both english and metric units, hammer cross pein 220 grams / 250 grams / 0.5 lb with handle., electrical symbol and accessories chart, vice hand 50 mm jaw, hacksaw frame fixed type 150 mm, plier round nose, 4/100 mm, guage- wire imperial standard, crimping tool for crimping 16 sq mm to 95 sq.mm, square engineers 6/ 15 cm blade, multi meter (analog) 0 to 1000 m ohms, 2v to 500 v,100 microa to 10a dc and ac, load bank (variable) up to 1.2 kw ( lamp / heater type), earth gi plate 60cm x 60cm x 6mm, earth electrode secondary cu strip 20x5mm, tap set metric 2 to 10 mm (set of 9 pcs) with wrench, hand trolley with 4 wheels 500mm x 750 mm, rooftop mounting structure for 4 x 250 w solar panels mounting practice, with tilt adjustment, protective relays and contactors rack suitable for practice of control circuits using banana plugs and sockets, cables twisted pair nonmetallic sheathed cable underground feeder cable ribbon cable metallic sheathed cable multi-conductor cable coaxial cable direct-buried cable 1 mtr each, bolts, nuts, anchor bolts, washers, screws, other pins, lugs, megger 500 volts cum continuity tester/insulation tester, solar insulation meter, magnetic flux meter 0-500 tesla, tong tester ( 0 - 100 a multi range ), soldering iron exchangable copper tip 65 watt, battery charger 0 - 6 - 9 - 12 - 24 - 48 v, 30amp, solar charge controller with dusk to dawn automatic switching 12v, 10a, solar charge controller with manual switch ( day lighting) 12 v 10 a, solar lantern cfl type, solar lantern assembly sets, solar cell kit, clinometer for angle measurement, level spirit for floor level check, dc table fan 12v, a.c. voltmeter m.i. 0-500 v, voltmeter (0-30v) (table model), voltmeter (0-100v) (table model), ampere meter 0 to 1 amp. (dc), ammeter m.c.0-5 d.c, ammeter m.c. 0-20 a centre zero, ammeter m.c. 0-50 a centre zero, single phase power factor meter, rheostat 0-1 ohms, rheostat 0-10 ohms 5 amp, rheostat 0-25 ohms 1 amp, rheostat 0-300 ohms 5 amp, a.c. energy meter (single phase 10 amp. 240 v), energy meter 3 ph 440 v,15 a, 4 wire, kilo watt (kw) meter analog 0-1.5-3kw, pressure coil rating- 240v/440v, current rating-5a/10a analog, portable type housed in bakelite case, watt meter (digital), phase sequence tester., frequency meter 45 to 55 hz, led lights 12 v dc, led lights 6 v dc, rubber gloves pair, gloves cotton, gum boots, safety goggles/ glass (plastic or fiber), wiring board on stand 3 meters x 1meter with 0.5 meter projection on the top, bidders should first download and review all available tender documents. These documents generally include the Notice Inviting Tender (NIT), Bill of Quantities (BOQ), technical specifications, eligibility criteria, scope of work, and bid submission instructions.


Tender Governemnt Authorities like Department Of Employment And Training DET usually publish these documents on their official eProcurement portals, departmental tender portals, the GeM Tender Portal, or other government procurement platforms or on newspapre. Finding and accessing the correct tender documents across multiple portals can sometimes be time-consuming for bidders. 


To make the process easier, Tender18 provides quick access to the available tender documents related to this Umarpada , Gujarat tender on a single page. Businesses involved in solar charge controller,power factor meter,insulation tester,earth electrode,conductor cable,battery charger,frequency meter,plastic handle,sheathed cable,soldering iron,safety goggles,hacksaw frame,crimping tool,coaxial cable,solar lantern,rubber gloves,screw driver,solar panels,feeder cable,ribbon cable,ac voltmeter,ampere meter,power factor,energy meter,safety tool,solar cell,watt meter,led lights,load bank,table fan,gum boots,battery,bolts related products, services, or works can conveniently download the relevant documents and review the tender requirements without spending time searching across different procurement portals.

The tender for tools equipment solar technician trade toolkit , equipment , toolkit-equipment , equipment attachment , safety tool , equipment furniture, screw driver insulated /150 mm, screw driver insulated plastic handle 5 mm tip length 200 mm, screw driver electrician 250 mm thin stem insulated handle magnetic point, knife double bladed electrician 100 mm, rule steel 30 cm graduated both english and metric units, hammer cross pein 220 grams / 250 grams / 0.5 lb with handle., electrical symbol and accessories chart, vice hand 50 mm jaw, hacksaw frame fixed type 150 mm, plier round nose, 4/100 mm, guage- wire imperial standard, crimping tool for crimping 16 sq mm to 95 sq.mm, square engineers 6/ 15 cm blade, multi meter (analog) 0 to 1000 m ohms, 2v to 500 v,100 microa to 10a dc and ac, load bank (variable) up to 1.2 kw ( lamp / heater type), earth gi plate 60cm x 60cm x 6mm, earth electrode secondary cu strip 20x5mm, tap set metric 2 to 10 mm (set of 9 pcs) with wrench, hand trolley with 4 wheels 500mm x 750 mm, rooftop mounting structure for 4 x 250 w solar panels mounting practice, with tilt adjustment, protective relays and contactors rack suitable for practice of control circuits using banana plugs and sockets, cables twisted pair nonmetallic sheathed cable underground feeder cable ribbon cable metallic sheathed cable multi-conductor cable coaxial cable direct-buried cable 1 mtr each, bolts, nuts, anchor bolts, washers, screws, other pins, lugs, megger 500 volts cum continuity tester/insulation tester, solar insulation meter, magnetic flux meter 0-500 tesla, tong tester ( 0 - 100 a multi range ), soldering iron exchangable copper tip 65 watt, battery charger 0 - 6 - 9 - 12 - 24 - 48 v, 30amp, solar charge controller with dusk to dawn automatic switching 12v, 10a, solar charge controller with manual switch ( day lighting) 12 v 10 a, solar lantern cfl type, solar lantern assembly sets, solar cell kit, clinometer for angle measurement, level spirit for floor level check, dc table fan 12v, a.c. voltmeter m.i. 0-500 v, voltmeter (0-30v) (table model), voltmeter (0-100v) (table model), ampere meter 0 to 1 amp. (dc), ammeter m.c.0-5 d.c, ammeter m.c. 0-20 a centre zero, ammeter m.c. 0-50 a centre zero, single phase power factor meter, rheostat 0-1 ohms, rheostat 0-10 ohms 5 amp, rheostat 0-25 ohms 1 amp, rheostat 0-300 ohms 5 amp, a.c. energy meter (single phase 10 amp. 240 v), energy meter 3 ph 440 v,15 a, 4 wire, kilo watt (kw) meter analog 0-1.5-3kw, pressure coil rating- 240v/440v, current rating-5a/10a analog, portable type housed in bakelite case, watt meter (digital), phase sequence tester., frequency meter 45 to 55 hz, led lights 12 v dc, led lights 6 v dc, rubber gloves pair, gloves cotton, gum boots, safety goggles/ glass (plastic or fiber), wiring board on stand 3 meters x 1meter with 0.5 meter projection on the top from Umarpada, Gujarat may be relevant for contractors, suppliers, vendors, manufacturers, consultants, service providers, startups, MSMEs, and other organizations involved in solar charge controller,power factor meter,insulation tester,earth electrode,conductor cable,battery charger,frequency meter,plastic handle,sheathed cable,soldering iron,safety goggles,hacksaw frame,crimping tool,coaxial cable,solar lantern,rubber gloves,screw driver,solar panels,feeder cable,ribbon cable,ac voltmeter,ampere meter,power factor,energy meter,safety tool,solar cell,watt meter,led lights,load bank,table fan,gum boots,battery,bolts related products, services, or works. However, eligibility to participate depends on the qualification criteria specified by Department Of Employment And Training DET in the official tender documents.

Before submitting a bid, interested applicants should carefully review the eligibility conditions, technical requirements, financial criteria, work experience requirements, annual turnover conditions, registrations, certifications, and any other supporting documents required by the tendering authority. The detailed qualification requirements and bidder eligibility criteria are available in the tender notice and related documents provided on this page. 

Ensuring compliance with all eligibility and qualification requirements before bid submission can help bidders avoid disqualification and improve their chances of successful participation in the tender process.

Tende18 provides comprehensive tender bidding services, including a complete tender summary along with a detailed analysis of the Tender Qualification and Eligibility Criteria.

Interested in participating in the tender for tools equipment solar technician trade toolkit , equipment , toolkit-equipment , equipment attachment , safety tool , equipment furniture, screw driver insulated /150 mm, screw driver insulated plastic handle 5 mm tip length 200 mm, screw driver electrician 250 mm thin stem insulated handle magnetic point, knife double bladed electrician 100 mm, rule steel 30 cm graduated both english and metric units, hammer cross pein 220 grams / 250 grams / 0.5 lb with handle., electrical symbol and accessories chart, vice hand 50 mm jaw, hacksaw frame fixed type 150 mm, plier round nose, 4/100 mm, guage- wire imperial standard, crimping tool for crimping 16 sq mm to 95 sq.mm, square engineers 6/ 15 cm blade, multi meter (analog) 0 to 1000 m ohms, 2v to 500 v,100 microa to 10a dc and ac, load bank (variable) up to 1.2 kw ( lamp / heater type), earth gi plate 60cm x 60cm x 6mm, earth electrode secondary cu strip 20x5mm, tap set metric 2 to 10 mm (set of 9 pcs) with wrench, hand trolley with 4 wheels 500mm x 750 mm, rooftop mounting structure for 4 x 250 w solar panels mounting practice, with tilt adjustment, protective relays and contactors rack suitable for practice of control circuits using banana plugs and sockets, cables twisted pair nonmetallic sheathed cable underground feeder cable ribbon cable metallic sheathed cable multi-conductor cable coaxial cable direct-buried cable 1 mtr each, bolts, nuts, anchor bolts, washers, screws, other pins, lugs, megger 500 volts cum continuity tester/insulation tester, solar insulation meter, magnetic flux meter 0-500 tesla, tong tester ( 0 - 100 a multi range ), soldering iron exchangable copper tip 65 watt, battery charger 0 - 6 - 9 - 12 - 24 - 48 v, 30amp, solar charge controller with dusk to dawn automatic switching 12v, 10a, solar charge controller with manual switch ( day lighting) 12 v 10 a, solar lantern cfl type, solar lantern assembly sets, solar cell kit, clinometer for angle measurement, level spirit for floor level check, dc table fan 12v, a.c. voltmeter m.i. 0-500 v, voltmeter (0-30v) (table model), voltmeter (0-100v) (table model), ampere meter 0 to 1 amp. (dc), ammeter m.c.0-5 d.c, ammeter m.c. 0-20 a centre zero, ammeter m.c. 0-50 a centre zero, single phase power factor meter, rheostat 0-1 ohms, rheostat 0-10 ohms 5 amp, rheostat 0-25 ohms 1 amp, rheostat 0-300 ohms 5 amp, a.c. energy meter (single phase 10 amp. 240 v), energy meter 3 ph 440 v,15 a, 4 wire, kilo watt (kw) meter analog 0-1.5-3kw, pressure coil rating- 240v/440v, current rating-5a/10a analog, portable type housed in bakelite case, watt meter (digital), phase sequence tester., frequency meter 45 to 55 hz, led lights 12 v dc, led lights 6 v dc, rubber gloves pair, gloves cotton, gum boots, safety goggles/ glass (plastic or fiber), wiring board on stand 3 meters x 1meter with 0.5 meter projection on the top issued by Department Of Employment And Training DET for solar charge controller,power factor meter,insulation tester,earth electrode,conductor cable,battery charger,frequency meter,plastic handle,sheathed cable,soldering iron,safety goggles,hacksaw frame,crimping tool,coaxial cable,solar lantern,rubber gloves,screw driver,solar panels,feeder cable,ribbon cable,ac voltmeter,ampere meter,power factor,energy meter,safety tool,solar cell,watt meter,led lights,load bank,table fan,gum boots,battery,bolts related work in Umarpada, Gujarat? TENDER18 provides complete assistance to help businesses understand tender requirements, access tender documents, review eligibility criteria, qualification requirements, important dates, and bid submission guidelines associated with this tender.

Our Tender18 Expert Technical team can assist with vendor and GeM registration on the relevant departmental, eProcurement, GeM, or government tender portal, preparation of technical and financial bid documents, compliance with qualification criteria, document verification, and complete online tender submission support. Whether you are a contractor, supplier, manufacturer, consultant, startup, or MSME working in the field of solar charge controller,power factor meter,insulation tester,earth electrode,conductor cable,battery charger,frequency meter,plastic handle,sheathed cable,soldering iron,safety goggles,hacksaw frame,crimping tool,coaxial cable,solar lantern,rubber gloves,screw driver,solar panels,feeder cable,ribbon cable,ac voltmeter,ampere meter,power factor,energy meter,safety tool,solar cell,watt meter,led lights,load bank,table fan,gum boots,battery,bolts, Tender18 can help simplify the tender participation process and support you throughout every stage of bidding for this tender. so that tender18 is one the top leading tender consultant in Inda.

1.

Whom should I contact if I have further queries about the Tender scope?

You can fill out the integrated inquiry form below on this detail page to share your company profile. Our consultancy desk will review your query regarding solar charge controller,power factor meter,insulation tester,earth electrode,conductor cable,battery charger,frequency meter,plastic handle,sheathed cable,soldering iron,safety goggles,hacksaw frame,crimping tool,coaxial cable,solar lantern,rubber gloves,screw driver,solar panels,feeder cable,ribbon cable,ac voltmeter,ampere meter,power factor,energy meter,safety tool,solar cell,watt meter,led lights,load bank,table fan,gum boots,battery,bolts parameters and guide you on how to coordinate efficiently with the procurement team of Department Of Employment And Training DET

2.

How can Tender18 assist my business in winning this government contract?

Tender18 provides end-to-end professional bidding support and documentation advisory for Tender For Tools Equipment Solar Technician Trade Toolkit , Equipment , Toolkit-equipment , Equipment Attachment , Safety Tool , Equipment Furniture, Screw Driver Insulated /150 Mm, Screw Driver Insulated Plastic Handle 5 Mm Tip Length 200 Mm, Screw Driver Electrician 250 Mm Thin Stem Insulated Handle Magnetic Point, Knife Double Bladed Electrician 100 Mm, Rule Steel 30 Cm Graduated Both English And Metric Units, Hammer Cross Pein 220 Grams / 250 Grams / 0.5 Lb With Handle., Electrical Symbol And Accessories Chart, Vice Hand 50 Mm Jaw, Hacksaw Frame Fixed Type 150 Mm, Plier Round Nose, 4/100 Mm, Guage- Wire Imperial Standard, Crimping Tool For Crimping 16 Sq Mm To 95 Sq.mm, Square Engineers 6/ 15 Cm Blade, Multi Meter (analog) 0 To 1000 M Ohms, 2v To 500 V,100 Microa To 10a Dc And Ac, Load Bank (variable) Up To 1.2 Kw ( Lamp / Heater Type), Earth Gi Plate 60cm X 60cm X 6mm, Earth Electrode Secondary Cu Strip 20x5mm, Tap Set Metric 2 To 10 Mm (set Of 9 Pcs) With Wrench, Hand Trolley With 4 Wheels 500mm X 750 Mm, Rooftop Mounting Structure For 4 X 250 W Solar Panels Mounting Practice, With Tilt Adjustment, Protective Relays And Contactors Rack Suitable For Practice Of Control Circuits Using Banana Plugs And Sockets, Cables Twisted Pair Nonmetallic Sheathed Cable Underground Feeder Cable Ribbon Cable Metallic Sheathed Cable Multi-conductor Cable Coaxial Cable Direct-buried Cable 1 Mtr Each, Bolts, Nuts, Anchor Bolts, Washers, Screws, Other Pins, Lugs, Megger 500 Volts Cum Continuity Tester/insulation Tester, Solar Insulation Meter, Magnetic Flux Meter 0-500 Tesla, Tong Tester ( 0 - 100 A Multi Range ), Soldering Iron Exchangable Copper Tip 65 Watt, Battery Charger 0 - 6 - 9 - 12 - 24 - 48 V, 30amp, Solar Charge Controller With Dusk To Dawn Automatic Switching 12v, 10a, Solar Charge Controller With Manual Switch ( Day Lighting) 12 V 10 A, Solar Lantern Cfl Type, Solar Lantern Assembly Sets, Solar Cell Kit, Clinometer For Angle Measurement, Level Spirit For Floor Level Check, Dc Table Fan 12v, A.c. Voltmeter M.i. 0-500 V, Voltmeter (0-30v) (table Model), Voltmeter (0-100v) (table Model), Ampere Meter 0 To 1 Amp. (dc), Ammeter M.c.0-5 D.c, Ammeter M.c. 0-20 A Centre Zero, Ammeter M.c. 0-50 A Centre Zero, Single Phase Power Factor Meter, Rheostat 0-1 Ohms, Rheostat 0-10 Ohms 5 Amp, Rheostat 0-25 Ohms 1 Amp, Rheostat 0-300 Ohms 5 Amp, A.c. Energy Meter (single Phase 10 Amp. 240 V), Energy Meter 3 Ph 440 V,15 A, 4 Wire, Kilo Watt (kw) Meter Analog 0-1.5-3kw, Pressure Coil Rating- 240v/440v, Current Rating-5a/10a Analog, Portable Type Housed In Bakelite Case, Watt Meter (digital), Phase Sequence Tester., Frequency Meter 45 To 55 Hz, Led Lights 12 V Dc, Led Lights 6 V Dc, Rubber Gloves Pair, Gloves Cotton, Gum Boots, Safety Goggles/ Glass (plastic Or Fiber), Wiring Board On Stand 3 Meters X 1meter With 0.5 Meter Projection On The Top . Our senior analysts help you decode the complete project guidelines, manage accurate costing sheets, and complete error-free submissions on the official platform used by Department Of Employment And Training DET.

3.

What are the main reasons for a technical tender rejection?

Most online bids face rejection during the initial evaluation round due to avoidable errors like uploading blurred document scans, submitting expired DSCs, or missing critical experience papers required for Tender For Tools Equipment Solar Technician Trade Toolkit , Equipment , Toolkit-equipment , Equipment Attachment , Safety Tool , Equipment Furniture, Screw Driver Insulated /150 Mm, Screw Driver Insulated Plastic Handle 5 Mm Tip Length 200 Mm, Screw Driver Electrician 250 Mm Thin Stem Insulated Handle Magnetic Point, Knife Double Bladed Electrician 100 Mm, Rule Steel 30 Cm Graduated Both English And Metric Units, Hammer Cross Pein 220 Grams / 250 Grams / 0.5 Lb With Handle., Electrical Symbol And Accessories Chart, Vice Hand 50 Mm Jaw, Hacksaw Frame Fixed Type 150 Mm, Plier Round Nose, 4/100 Mm, Guage- Wire Imperial Standard, Crimping Tool For Crimping 16 Sq Mm To 95 Sq.mm, Square Engineers 6/ 15 Cm Blade, Multi Meter (analog) 0 To 1000 M Ohms, 2v To 500 V,100 Microa To 10a Dc And Ac, Load Bank (variable) Up To 1.2 Kw ( Lamp / Heater Type), Earth Gi Plate 60cm X 60cm X 6mm, Earth Electrode Secondary Cu Strip 20x5mm, Tap Set Metric 2 To 10 Mm (set Of 9 Pcs) With Wrench, Hand Trolley With 4 Wheels 500mm X 750 Mm, Rooftop Mounting Structure For 4 X 250 W Solar Panels Mounting Practice, With Tilt Adjustment, Protective Relays And Contactors Rack Suitable For Practice Of Control Circuits Using Banana Plugs And Sockets, Cables Twisted Pair Nonmetallic Sheathed Cable Underground Feeder Cable Ribbon Cable Metallic Sheathed Cable Multi-conductor Cable Coaxial Cable Direct-buried Cable 1 Mtr Each, Bolts, Nuts, Anchor Bolts, Washers, Screws, Other Pins, Lugs, Megger 500 Volts Cum Continuity Tester/insulation Tester, Solar Insulation Meter, Magnetic Flux Meter 0-500 Tesla, Tong Tester ( 0 - 100 A Multi Range ), Soldering Iron Exchangable Copper Tip 65 Watt, Battery Charger 0 - 6 - 9 - 12 - 24 - 48 V, 30amp, Solar Charge Controller With Dusk To Dawn Automatic Switching 12v, 10a, Solar Charge Controller With Manual Switch ( Day Lighting) 12 V 10 A, Solar Lantern Cfl Type, Solar Lantern Assembly Sets, Solar Cell Kit, Clinometer For Angle Measurement, Level Spirit For Floor Level Check, Dc Table Fan 12v, A.c. Voltmeter M.i. 0-500 V, Voltmeter (0-30v) (table Model), Voltmeter (0-100v) (table Model), Ampere Meter 0 To 1 Amp. (dc), Ammeter M.c.0-5 D.c, Ammeter M.c. 0-20 A Centre Zero, Ammeter M.c. 0-50 A Centre Zero, Single Phase Power Factor Meter, Rheostat 0-1 Ohms, Rheostat 0-10 Ohms 5 Amp, Rheostat 0-25 Ohms 1 Amp, Rheostat 0-300 Ohms 5 Amp, A.c. Energy Meter (single Phase 10 Amp. 240 V), Energy Meter 3 Ph 440 V,15 A, 4 Wire, Kilo Watt (kw) Meter Analog 0-1.5-3kw, Pressure Coil Rating- 240v/440v, Current Rating-5a/10a Analog, Portable Type Housed In Bakelite Case, Watt Meter (digital), Phase Sequence Tester., Frequency Meter 45 To 55 Hz, Led Lights 12 V Dc, Led Lights 6 V Dc, Rubber Gloves Pair, Gloves Cotton, Gum Boots, Safety Goggles/ Glass (plastic Or Fiber), Wiring Board On Stand 3 Meters X 1meter With 0.5 Meter Projection On The Top in Gujarat.

4.

Can contractors located outside the local region participate in this bid?

Eligibility for outstation bidders depends entirely on the terms set inside the document for Tender For Tools Equipment Solar Technician Trade Toolkit , Equipment , Toolkit-equipment , Equipment Attachment , Safety Tool , Equipment Furniture, Screw Driver Insulated /150 Mm, Screw Driver Insulated Plastic Handle 5 Mm Tip Length 200 Mm, Screw Driver Electrician 250 Mm Thin Stem Insulated Handle Magnetic Point, Knife Double Bladed Electrician 100 Mm, Rule Steel 30 Cm Graduated Both English And Metric Units, Hammer Cross Pein 220 Grams / 250 Grams / 0.5 Lb With Handle., Electrical Symbol And Accessories Chart, Vice Hand 50 Mm Jaw, Hacksaw Frame Fixed Type 150 Mm, Plier Round Nose, 4/100 Mm, Guage- Wire Imperial Standard, Crimping Tool For Crimping 16 Sq Mm To 95 Sq.mm, Square Engineers 6/ 15 Cm Blade, Multi Meter (analog) 0 To 1000 M Ohms, 2v To 500 V,100 Microa To 10a Dc And Ac, Load Bank (variable) Up To 1.2 Kw ( Lamp / Heater Type), Earth Gi Plate 60cm X 60cm X 6mm, Earth Electrode Secondary Cu Strip 20x5mm, Tap Set Metric 2 To 10 Mm (set Of 9 Pcs) With Wrench, Hand Trolley With 4 Wheels 500mm X 750 Mm, Rooftop Mounting Structure For 4 X 250 W Solar Panels Mounting Practice, With Tilt Adjustment, Protective Relays And Contactors Rack Suitable For Practice Of Control Circuits Using Banana Plugs And Sockets, Cables Twisted Pair Nonmetallic Sheathed Cable Underground Feeder Cable Ribbon Cable Metallic Sheathed Cable Multi-conductor Cable Coaxial Cable Direct-buried Cable 1 Mtr Each, Bolts, Nuts, Anchor Bolts, Washers, Screws, Other Pins, Lugs, Megger 500 Volts Cum Continuity Tester/insulation Tester, Solar Insulation Meter, Magnetic Flux Meter 0-500 Tesla, Tong Tester ( 0 - 100 A Multi Range ), Soldering Iron Exchangable Copper Tip 65 Watt, Battery Charger 0 - 6 - 9 - 12 - 24 - 48 V, 30amp, Solar Charge Controller With Dusk To Dawn Automatic Switching 12v, 10a, Solar Charge Controller With Manual Switch ( Day Lighting) 12 V 10 A, Solar Lantern Cfl Type, Solar Lantern Assembly Sets, Solar Cell Kit, Clinometer For Angle Measurement, Level Spirit For Floor Level Check, Dc Table Fan 12v, A.c. Voltmeter M.i. 0-500 V, Voltmeter (0-30v) (table Model), Voltmeter (0-100v) (table Model), Ampere Meter 0 To 1 Amp. (dc), Ammeter M.c.0-5 D.c, Ammeter M.c. 0-20 A Centre Zero, Ammeter M.c. 0-50 A Centre Zero, Single Phase Power Factor Meter, Rheostat 0-1 Ohms, Rheostat 0-10 Ohms 5 Amp, Rheostat 0-25 Ohms 1 Amp, Rheostat 0-300 Ohms 5 Amp, A.c. Energy Meter (single Phase 10 Amp. 240 V), Energy Meter 3 Ph 440 V,15 A, 4 Wire, Kilo Watt (kw) Meter Analog 0-1.5-3kw, Pressure Coil Rating- 240v/440v, Current Rating-5a/10a Analog, Portable Type Housed In Bakelite Case, Watt Meter (digital), Phase Sequence Tester., Frequency Meter 45 To 55 Hz, Led Lights 12 V Dc, Led Lights 6 V Dc, Rubber Gloves Pair, Gloves Cotton, Gum Boots, Safety Goggles/ Glass (plastic Or Fiber), Wiring Board On Stand 3 Meters X 1meter With 0.5 Meter Projection On The Top. While many public sector projects allow national competitive bidding, certain localized works require local offices or specific registration metrics in Umarpada.

5.

Do I need an active GeM Portal registration to apply for this work?

If this procurement is routed through the central marketplace, an active GeM Seller ID is mandatory to supply solar charge controller,power factor meter,insulation tester,earth electrode,conductor cable,battery charger,frequency meter,plastic handle,sheathed cable,soldering iron,safety goggles,hacksaw frame,crimping tool,coaxial cable,solar lantern,rubber gloves,screw driver,solar panels,feeder cable,ribbon cable,ac voltmeter,ampere meter,power factor,energy meter,safety tool,solar cell,watt meter,led lights,load bank,table fan,gum boots,battery,bolts items. Tender18 offers complete assistance for brand cataloging, profile creation, and vendor assessment required officially by Department Of Employment And Training DET

6.

What are the primary legal documents required to submit a valid bid?

To register an eligible bid for these solar charge controller,power factor meter,insulation tester,earth electrode,conductor cable,battery charger,frequency meter,plastic handle,sheathed cable,soldering iron,safety goggles,hacksaw frame,crimping tool,coaxial cable,solar lantern,rubber gloves,screw driver,solar panels,feeder cable,ribbon cable,ac voltmeter,ampere meter,power factor,energy meter,safety tool,solar cell,watt meter,led lights,load bank,table fan,gum boots,battery,bolts contracts, companies must prepare their core compliance documents. Vendors operating across Gujarat must ensure they possess a valid GST registration, permanent account number (PAN), and active Class-3 Digital Signature Certificates.

7.

What products or services are required for this active work?

This public procurement cycle is specifically looking for qualified vendors and suppliers who can provide high-quality solar charge controller,power factor meter,insulation tester,earth electrode,conductor cable,battery charger,frequency meter,plastic handle,sheathed cable,soldering iron,safety goggles,hacksaw frame,crimping tool,coaxial cable,solar lantern,rubber gloves,screw driver,solar panels,feeder cable,ribbon cable,ac voltmeter,ampere meter,power factor,energy meter,safety tool,solar cell,watt meter,led lights,load bank,table fan,gum boots,battery,bolts solutions. The operational execution, delivery, and deployment of these materials must be managed locally within the Umarpada region.

8.

Where can I review the estimated cost or budget details for this Tender?

The estimated project cost and budget thresholds can be reviewed directly inside the tender document. Bidders can analyze these qualification files to check if their firm meets the financial capability criteria specified for Tender For Tools Equipment Solar Technician Trade Toolkit , Equipment , Toolkit-equipment , Equipment Attachment , Safety Tool , Equipment Furniture, Screw Driver Insulated /150 Mm, Screw Driver Insulated Plastic Handle 5 Mm Tip Length 200 Mm, Screw Driver Electrician 250 Mm Thin Stem Insulated Handle Magnetic Point, Knife Double Bladed Electrician 100 Mm, Rule Steel 30 Cm Graduated Both English And Metric Units, Hammer Cross Pein 220 Grams / 250 Grams / 0.5 Lb With Handle., Electrical Symbol And Accessories Chart, Vice Hand 50 Mm Jaw, Hacksaw Frame Fixed Type 150 Mm, Plier Round Nose, 4/100 Mm, Guage- Wire Imperial Standard, Crimping Tool For Crimping 16 Sq Mm To 95 Sq.mm, Square Engineers 6/ 15 Cm Blade, Multi Meter (analog) 0 To 1000 M Ohms, 2v To 500 V,100 Microa To 10a Dc And Ac, Load Bank (variable) Up To 1.2 Kw ( Lamp / Heater Type), Earth Gi Plate 60cm X 60cm X 6mm, Earth Electrode Secondary Cu Strip 20x5mm, Tap Set Metric 2 To 10 Mm (set Of 9 Pcs) With Wrench, Hand Trolley With 4 Wheels 500mm X 750 Mm, Rooftop Mounting Structure For 4 X 250 W Solar Panels Mounting Practice, With Tilt Adjustment, Protective Relays And Contactors Rack Suitable For Practice Of Control Circuits Using Banana Plugs And Sockets, Cables Twisted Pair Nonmetallic Sheathed Cable Underground Feeder Cable Ribbon Cable Metallic Sheathed Cable Multi-conductor Cable Coaxial Cable Direct-buried Cable 1 Mtr Each, Bolts, Nuts, Anchor Bolts, Washers, Screws, Other Pins, Lugs, Megger 500 Volts Cum Continuity Tester/insulation Tester, Solar Insulation Meter, Magnetic Flux Meter 0-500 Tesla, Tong Tester ( 0 - 100 A Multi Range ), Soldering Iron Exchangable Copper Tip 65 Watt, Battery Charger 0 - 6 - 9 - 12 - 24 - 48 V, 30amp, Solar Charge Controller With Dusk To Dawn Automatic Switching 12v, 10a, Solar Charge Controller With Manual Switch ( Day Lighting) 12 V 10 A, Solar Lantern Cfl Type, Solar Lantern Assembly Sets, Solar Cell Kit, Clinometer For Angle Measurement, Level Spirit For Floor Level Check, Dc Table Fan 12v, A.c. Voltmeter M.i. 0-500 V, Voltmeter (0-30v) (table Model), Voltmeter (0-100v) (table Model), Ampere Meter 0 To 1 Amp. (dc), Ammeter M.c.0-5 D.c, Ammeter M.c. 0-20 A Centre Zero, Ammeter M.c. 0-50 A Centre Zero, Single Phase Power Factor Meter, Rheostat 0-1 Ohms, Rheostat 0-10 Ohms 5 Amp, Rheostat 0-25 Ohms 1 Amp, Rheostat 0-300 Ohms 5 Amp, A.c. Energy Meter (single Phase 10 Amp. 240 V), Energy Meter 3 Ph 440 V,15 A, 4 Wire, Kilo Watt (kw) Meter Analog 0-1.5-3kw, Pressure Coil Rating- 240v/440v, Current Rating-5a/10a Analog, Portable Type Housed In Bakelite Case, Watt Meter (digital), Phase Sequence Tester., Frequency Meter 45 To 55 Hz, Led Lights 12 V Dc, Led Lights 6 V Dc, Rubber Gloves Pair, Gloves Cotton, Gum Boots, Safety Goggles/ Glass (plastic Or Fiber), Wiring Board On Stand 3 Meters X 1meter With 0.5 Meter Projection On The Top by Department Of Employment And Training DET

9.

How can I download the official BOQ file for this opportunity?

You can download the commercial Bill of Quantities (BOQ) spreadsheet directly using the secure link provided on this page. The BOQ file contains the item descriptions and rate filling forms officially validated for Tender For Tools Equipment Solar Technician Trade Toolkit , Equipment , Toolkit-equipment , Equipment Attachment , Safety Tool , Equipment Furniture, Screw Driver Insulated /150 Mm, Screw Driver Insulated Plastic Handle 5 Mm Tip Length 200 Mm, Screw Driver Electrician 250 Mm Thin Stem Insulated Handle Magnetic Point, Knife Double Bladed Electrician 100 Mm, Rule Steel 30 Cm Graduated Both English And Metric Units, Hammer Cross Pein 220 Grams / 250 Grams / 0.5 Lb With Handle., Electrical Symbol And Accessories Chart, Vice Hand 50 Mm Jaw, Hacksaw Frame Fixed Type 150 Mm, Plier Round Nose, 4/100 Mm, Guage- Wire Imperial Standard, Crimping Tool For Crimping 16 Sq Mm To 95 Sq.mm, Square Engineers 6/ 15 Cm Blade, Multi Meter (analog) 0 To 1000 M Ohms, 2v To 500 V,100 Microa To 10a Dc And Ac, Load Bank (variable) Up To 1.2 Kw ( Lamp / Heater Type), Earth Gi Plate 60cm X 60cm X 6mm, Earth Electrode Secondary Cu Strip 20x5mm, Tap Set Metric 2 To 10 Mm (set Of 9 Pcs) With Wrench, Hand Trolley With 4 Wheels 500mm X 750 Mm, Rooftop Mounting Structure For 4 X 250 W Solar Panels Mounting Practice, With Tilt Adjustment, Protective Relays And Contactors Rack Suitable For Practice Of Control Circuits Using Banana Plugs And Sockets, Cables Twisted Pair Nonmetallic Sheathed Cable Underground Feeder Cable Ribbon Cable Metallic Sheathed Cable Multi-conductor Cable Coaxial Cable Direct-buried Cable 1 Mtr Each, Bolts, Nuts, Anchor Bolts, Washers, Screws, Other Pins, Lugs, Megger 500 Volts Cum Continuity Tester/insulation Tester, Solar Insulation Meter, Magnetic Flux Meter 0-500 Tesla, Tong Tester ( 0 - 100 A Multi Range ), Soldering Iron Exchangable Copper Tip 65 Watt, Battery Charger 0 - 6 - 9 - 12 - 24 - 48 V, 30amp, Solar Charge Controller With Dusk To Dawn Automatic Switching 12v, 10a, Solar Charge Controller With Manual Switch ( Day Lighting) 12 V 10 A, Solar Lantern Cfl Type, Solar Lantern Assembly Sets, Solar Cell Kit, Clinometer For Angle Measurement, Level Spirit For Floor Level Check, Dc Table Fan 12v, A.c. Voltmeter M.i. 0-500 V, Voltmeter (0-30v) (table Model), Voltmeter (0-100v) (table Model), Ampere Meter 0 To 1 Amp. (dc), Ammeter M.c.0-5 D.c, Ammeter M.c. 0-20 A Centre Zero, Ammeter M.c. 0-50 A Centre Zero, Single Phase Power Factor Meter, Rheostat 0-1 Ohms, Rheostat 0-10 Ohms 5 Amp, Rheostat 0-25 Ohms 1 Amp, Rheostat 0-300 Ohms 5 Amp, A.c. Energy Meter (single Phase 10 Amp. 240 V), Energy Meter 3 Ph 440 V,15 A, 4 Wire, Kilo Watt (kw) Meter Analog 0-1.5-3kw, Pressure Coil Rating- 240v/440v, Current Rating-5a/10a Analog, Portable Type Housed In Bakelite Case, Watt Meter (digital), Phase Sequence Tester., Frequency Meter 45 To 55 Hz, Led Lights 12 V Dc, Led Lights 6 V Dc, Rubber Gloves Pair, Gloves Cotton, Gum Boots, Safety Goggles/ Glass (plastic Or Fiber), Wiring Board On Stand 3 Meters X 1meter With 0.5 Meter Projection On The Top within the Gujarat jurisdiction

10.

How can I find the submission closing date for this contract?

The official timeline and deadline details for Tender For Tools Equipment Solar Technician Trade Toolkit , Equipment , Toolkit-equipment , Equipment Attachment , Safety Tool , Equipment Furniture, Screw Driver Insulated /150 Mm, Screw Driver Insulated Plastic Handle 5 Mm Tip Length 200 Mm, Screw Driver Electrician 250 Mm Thin Stem Insulated Handle Magnetic Point, Knife Double Bladed Electrician 100 Mm, Rule Steel 30 Cm Graduated Both English And Metric Units, Hammer Cross Pein 220 Grams / 250 Grams / 0.5 Lb With Handle., Electrical Symbol And Accessories Chart, Vice Hand 50 Mm Jaw, Hacksaw Frame Fixed Type 150 Mm, Plier Round Nose, 4/100 Mm, Guage- Wire Imperial Standard, Crimping Tool For Crimping 16 Sq Mm To 95 Sq.mm, Square Engineers 6/ 15 Cm Blade, Multi Meter (analog) 0 To 1000 M Ohms, 2v To 500 V,100 Microa To 10a Dc And Ac, Load Bank (variable) Up To 1.2 Kw ( Lamp / Heater Type), Earth Gi Plate 60cm X 60cm X 6mm, Earth Electrode Secondary Cu Strip 20x5mm, Tap Set Metric 2 To 10 Mm (set Of 9 Pcs) With Wrench, Hand Trolley With 4 Wheels 500mm X 750 Mm, Rooftop Mounting Structure For 4 X 250 W Solar Panels Mounting Practice, With Tilt Adjustment, Protective Relays And Contactors Rack Suitable For Practice Of Control Circuits Using Banana Plugs And Sockets, Cables Twisted Pair Nonmetallic Sheathed Cable Underground Feeder Cable Ribbon Cable Metallic Sheathed Cable Multi-conductor Cable Coaxial Cable Direct-buried Cable 1 Mtr Each, Bolts, Nuts, Anchor Bolts, Washers, Screws, Other Pins, Lugs, Megger 500 Volts Cum Continuity Tester/insulation Tester, Solar Insulation Meter, Magnetic Flux Meter 0-500 Tesla, Tong Tester ( 0 - 100 A Multi Range ), Soldering Iron Exchangable Copper Tip 65 Watt, Battery Charger 0 - 6 - 9 - 12 - 24 - 48 V, 30amp, Solar Charge Controller With Dusk To Dawn Automatic Switching 12v, 10a, Solar Charge Controller With Manual Switch ( Day Lighting) 12 V 10 A, Solar Lantern Cfl Type, Solar Lantern Assembly Sets, Solar Cell Kit, Clinometer For Angle Measurement, Level Spirit For Floor Level Check, Dc Table Fan 12v, A.c. Voltmeter M.i. 0-500 V, Voltmeter (0-30v) (table Model), Voltmeter (0-100v) (table Model), Ampere Meter 0 To 1 Amp. (dc), Ammeter M.c.0-5 D.c, Ammeter M.c. 0-20 A Centre Zero, Ammeter M.c. 0-50 A Centre Zero, Single Phase Power Factor Meter, Rheostat 0-1 Ohms, Rheostat 0-10 Ohms 5 Amp, Rheostat 0-25 Ohms 1 Amp, Rheostat 0-300 Ohms 5 Amp, A.c. Energy Meter (single Phase 10 Amp. 240 V), Energy Meter 3 Ph 440 V,15 A, 4 Wire, Kilo Watt (kw) Meter Analog 0-1.5-3kw, Pressure Coil Rating- 240v/440v, Current Rating-5a/10a Analog, Portable Type Housed In Bakelite Case, Watt Meter (digital), Phase Sequence Tester., Frequency Meter 45 To 55 Hz, Led Lights 12 V Dc, Led Lights 6 V Dc, Rubber Gloves Pair, Gloves Cotton, Gum Boots, Safety Goggles/ Glass (plastic Or Fiber), Wiring Board On Stand 3 Meters X 1meter With 0.5 Meter Projection On The Top are available inside the detailed notification files. Bidders planning to target this contract in Umarpada should check the official portal schedule early to complete their online technical and financial submission well before the closing hours.

Get Expert Tender Bidding Support

Looking For Complete Tender Bidding Consultancy? Our Technical Experts Will Help You Prepare And Submit Your Tender Successfully.

Call Our Expert: +91 7069661818
Your Information Is 100% Secure & Confidential