tender for title1 , title2 , title3 , title4 , title5 , title6 , title7 , title8 , title9 , title10 , title11 , title12 , title13 , title14 , title15 , title16 , title17 , title18 , title19 , title20 , title21 , title22 , title23, construction of boundary wall at aecs secondary at narwapahar mines, earth work in excavation by mechanical means hydraulic excavator manual means over areas exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by engineer in charge. all kind of soil, filling available excavated earth excluding rock in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.50m., clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50m outside the periphery of the area cleared., providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth levelshelves,chajja,lintel,band,plain window sills,stsiarcase and spiral stair case above plinth level upto floor five level execluding the cost of centering,shuttering,finishing and reinforced with 1 ratio 1.5 ratio 3 1 cement 1.5 coarse sand 3 graded stone aggregate. 1 5 10 1 cement 5 coarse sand zone iii derived from natural sources 10 graded stone aggregate 40 mm nominal size derived from natural sources, providing and laying cement concrete in retaining walls, return walls, walls any thickness including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing 1 2 4 1 cement 2 coarse sand zone iii derived from natural sources 4 graded stone aggregate 20 mm nominal size derived from natural sources, centering and shuttering including strutting, propping etc and removal of form work for foundations, footings, bases for columns foundations, footings, bases for columns, centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete, centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers, centering and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts, steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo mechanically treated bars of grade fe 500d or more., steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. thermo mechanically treated bars of grade fe 500d or more., providing and laying in position machine batched and machine mixed design mix m 25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer in charge. note cement content considered in this item is at the rate 330 kg per cum. excess or less cement used as per design mix is payable or recoverable separately all works upto plinth level, providing and laying in position machine batched and machine mixed design mix m 25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge. (note cement content considered in this item is at the rate 330 kg per cum. excess or less cement used as per design mix is payable or recoverable separately. all works above plinth level upto floor v level., add for using extra cement in the items of design mix over and above the specified cement content therein., brick work with common burnt clay f.p.s. non modular bricks of class designation 7.5 in foundation and plinth in cement mortar 1 6 1 cement 6 coarse sand, brick work with common burnt clay f.p.s. non modular bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in cement mortar 1 6 1 cement 6 coarse sand, 12 mm cement plaster of mix 1 6 1 cement 6 coarse sand, 15 mm cement plaster on rough side of single or half brick wall of mix 1 6 1 cement 6 coarse sand, finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade new work two or more coats applied at the rate 1.43 ltr per 10 sqm over and including priming coat of exterior primer applied at the rate 2.20 kg per10 sqm, applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron steel works, painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new work, providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length total length 90 m, having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron y shaped placed 2.4m or 3.00 m apart and with 9 horizontal r.b.t. reinforced barbed wire, stud tied with g.i. staples and g.i. clips to retain horizontal, including necessary bolts or g.i. barbed wire tied to angle iron, all complete as per direction of engineer in charge, with reinforced barbed tape r.b.t. spring core 2.5mm thick wire of high tensile strength of 165 kg per sq.mm with tape 0.52 mm thick and weight 43.478 gm per metre cost of m.s. angle, c.c. blocks shall be paid separately, supplying at site angle iron post and strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.

Latest Tender Detail from uranium corporation of india limited UCIL for the tender for title1 , title2 , title3 , title4 , title5 , title6 , title7 , title8 , title9 , title10 , title11 , title12 , title13 , title14 , title15 , title16 , title17 , title18 , title19 , title20 , title21 , title22 , title23, construction of boundary wall at aecs secondary at narwapahar mines, earth work in excavation by mechanical means hydraulic excavator manual means over areas exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by engineer in charge. all kind of soil, filling available excavated earth excluding rock in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.50m., clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50m outside the periphery of the area cleared., providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth levelshelves,chajja,lintel,band,plain window sills,stsiarcase and spiral stair case above plinth level upto floor five level execluding the cost of centering,shuttering,finishing and reinforced with 1 ratio 1.5 ratio 3 1 cement 1.5 coarse sand 3 graded stone aggregate. 1 5 10 1 cement 5 coarse sand zone iii derived from natural sources 10 graded stone aggregate 40 mm nominal size derived from natural sources, providing and laying cement concrete in retaining walls, return walls, walls any thickness including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing 1 2 4 1 cement 2 coarse sand zone iii derived from natural sources 4 graded stone aggregate 20 mm nominal size derived from natural sources, centering and shuttering including strutting, propping etc and removal of form work for foundations, footings, bases for columns foundations, footings, bases for columns, centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete, centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers, centering and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts, steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo mechanically treated bars of grade fe 500d or more., steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. thermo mechanically treated bars of grade fe 500d or more., providing and laying in position machine batched and machine mixed design mix m 25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer in charge. note cement content considered in this item is at the rate 330 kg per cum. excess or less cement used as per design mix is payable or recoverable separately all works upto plinth level, providing and laying in position machine batched and machine mixed design mix m 25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge. (note cement content considered in this item is at the rate 330 kg per cum. excess or less cement used as per design mix is payable or recoverable separately. all works above plinth level upto floor v level., add for using extra cement in the items of design mix over and above the specified cement content therein., brick work with common burnt clay f.p.s. non modular bricks of class designation 7.5 in foundation and plinth in cement mortar 1 6 1 cement 6 coarse sand, brick work with common burnt clay f.p.s. non modular bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in cement mortar 1 6 1 cement 6 coarse sand, 12 mm cement plaster of mix 1 6 1 cement 6 coarse sand, 15 mm cement plaster on rough side of single or half brick wall of mix 1 6 1 cement 6 coarse sand, finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade new work two or more coats applied at the rate 1.43 ltr per 10 sqm over and including priming coat of exterior primer applied at the rate 2.20 kg per10 sqm, applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron steel works, painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new work, providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length total length 90 m, having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron y shaped placed 2.4m or 3.00 m apart and with 9 horizontal r.b.t. reinforced barbed wire, stud tied with g.i. staples and g.i. clips to retain horizontal, including necessary bolts or g.i. barbed wire tied to angle iron, all complete as per direction of engineer in charge, with reinforced barbed tape r.b.t. spring core 2.5mm thick wire of high tensile strength of 165 kg per sq.mm with tape 0.52 mm thick and weight 43.478 gm per metre cost of m.s. angle, c.c. blocks shall be paid separately, supplying at site angle iron post and strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete. in ghatshila, jharkhand,. Reference number 16139917. Don't miss out on this chance to be part of a significant project. Register for free today to access the complete tender details and download the necessary documents. Seize the opportunity with Tender 18!

T18 Ref No:16139917
Tender ID:GEM/2026/B/7754362
Tender Agency:uranium corporation of india limited UCIL
City:ghatshila
State:jharkhand
Tender Related Keywords :
Description :
total quantity = 8588 ----- document required from seller = experience criteria,bidder turnover,additional doc 1 (requested in atc),additional doc 2 (requested in atc),additional doc 3 (requested in atc),additional doc 4 (requested in atc) ----- evaluation method = total value wise evaluation
T18 Ref No:16139917Tender Value:2082145.4
Tender ID:GEM/2026/B/7754362Tender EMD:20821
Tender Agency:uranium corporation of india limited UCILTender Fee:Refer Document
City:ghatshilaPublished Date:Jul 07, 2026
State:jharkhandDue Date:Jul 28, 2026
Tender Related Keywords :reinforced cement concrete, synthetic enamel paint, cement concrete work, zinc chromate primer, hydraulic excavator, steel reinforcement, synthetic enamel, cement concrete, retaining walls, concertina coil, angle iron post, exterior paint, boundary wall, concrete work, zinc chromate, enamel paint, punched tape, coarse sand, steel works, barbed wire, earth work, brick work, angle iron, red oxide, rcc work, ms angle, bricks, boltsTender Opening Date:Jul 28, 2026
Description :total quantity = 8588 ----- document required from seller = experience criteria,bidder turnover,additional doc 1 (requested in atc),additional doc 2 (requested in atc),additional doc 3 (requested in atc),additional doc 4 (requested in atc) ----- evaluation method = total value wise evaluation

Get Complete Tender Documents to Participate

Tender NoticeBOQEligibilityEMD DetailsImportant Dates
We take all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Browse GeM Portal Tenders

This Government Tender has been Published  by Uranium Corporation Of India Limited UCIL for work related to reinforced cement concrete,synthetic enamel paint,cement concrete work,zinc chromate primer,hydraulic excavator,steel reinforcement,synthetic enamel,cement concrete,retaining walls,concertina coil,angle iron post,exterior paint,boundary wall,concrete work,zinc chromate,enamel paint,punched tape,coarse sand,steel works,barbed wire,earth work,brick work,angle iron,red oxide,rcc work,ms angle,bricks,bolts in Ghatshila, Jharkhand. The Tender work is tender for title1 , title2 , title3 , title4 , title5 , title6 , title7 , title8 , title9 , title10 , title11 , title12 , title13 , title14 , title15 , title16 , title17 , title18 , title19 , title20 , title21 , title22 , title23, construction of boundary wall at aecs secondary at narwapahar mines, earth work in excavation by mechanical means hydraulic excavator manual means over areas exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by engineer in charge. all kind of soil, filling available excavated earth excluding rock in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.50m., clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50m outside the periphery of the area cleared., providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth levelshelves,chajja,lintel,band,plain window sills,stsiarcase and spiral stair case above plinth level upto floor five level execluding the cost of centering,shuttering,finishing and reinforced with 1 ratio 1.5 ratio 3 1 cement 1.5 coarse sand 3 graded stone aggregate. 1 5 10 1 cement 5 coarse sand zone iii derived from natural sources 10 graded stone aggregate 40 mm nominal size derived from natural sources, providing and laying cement concrete in retaining walls, return walls, walls any thickness including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing 1 2 4 1 cement 2 coarse sand zone iii derived from natural sources 4 graded stone aggregate 20 mm nominal size derived from natural sources, centering and shuttering including strutting, propping etc and removal of form work for foundations, footings, bases for columns foundations, footings, bases for columns, centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete, centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers, centering and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts, steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo mechanically treated bars of grade fe 500d or more., steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. thermo mechanically treated bars of grade fe 500d or more., providing and laying in position machine batched and machine mixed design mix m 25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer in charge. note cement content considered in this item is at the rate 330 kg per cum. excess or less cement used as per design mix is payable or recoverable separately all works upto plinth level, providing and laying in position machine batched and machine mixed design mix m 25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge. (note cement content considered in this item is at the rate 330 kg per cum. excess or less cement used as per design mix is payable or recoverable separately. all works above plinth level upto floor v level., add for using extra cement in the items of design mix over and above the specified cement content therein., brick work with common burnt clay f.p.s. non modular bricks of class designation 7.5 in foundation and plinth in cement mortar 1 6 1 cement 6 coarse sand, brick work with common burnt clay f.p.s. non modular bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in cement mortar 1 6 1 cement 6 coarse sand, 12 mm cement plaster of mix 1 6 1 cement 6 coarse sand, 15 mm cement plaster on rough side of single or half brick wall of mix 1 6 1 cement 6 coarse sand, finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade new work two or more coats applied at the rate 1.43 ltr per 10 sqm over and including priming coat of exterior primer applied at the rate 2.20 kg per10 sqm, applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron steel works, painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new work, providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length total length 90 m, having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron y shaped placed 2.4m or 3.00 m apart and with 9 horizontal r.b.t. reinforced barbed wire, stud tied with g.i. staples and g.i. clips to retain horizontal, including necessary bolts or g.i. barbed wire tied to angle iron, all complete as per direction of engineer in charge, with reinforced barbed tape r.b.t. spring core 2.5mm thick wire of high tensile strength of 165 kg per sq.mm with tape 0.52 mm thick and weight 43.478 gm per metre cost of m.s. angle, c.c. blocks shall be paid separately, supplying at site angle iron post and strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.. Tender18 Provide this type Government Tender Information on daily basis.


This tender invites eligible contractors, suppliers, manufacturers, consultants, Startups, Msmes, traders and service providers to submit bids for the specified project, supply, service, or work requirement.


Before applying, interested bidders should review the tender scope, eligibility criteria, estimated contract value, important dates, technical requirements, reqired docuent list for bidder and bid submission instructions as per provided in the official tender documents. 


This Verified Information Provide By Tender18 in this page so Bidder Can Easiy  Understanding tender  requirements and bidders can prepare a compliant and competitive tender proposal.

To participate in the tender for title1 , title2 , title3 , title4 , title5 , title6 , title7 , title8 , title9 , title10 , title11 , title12 , title13 , title14 , title15 , title16 , title17 , title18 , title19 , title20 , title21 , title22 , title23, construction of boundary wall at aecs secondary at narwapahar mines, earth work in excavation by mechanical means hydraulic excavator manual means over areas exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by engineer in charge. all kind of soil, filling available excavated earth excluding rock in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.50m., clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50m outside the periphery of the area cleared., providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth levelshelves,chajja,lintel,band,plain window sills,stsiarcase and spiral stair case above plinth level upto floor five level execluding the cost of centering,shuttering,finishing and reinforced with 1 ratio 1.5 ratio 3 1 cement 1.5 coarse sand 3 graded stone aggregate. 1 5 10 1 cement 5 coarse sand zone iii derived from natural sources 10 graded stone aggregate 40 mm nominal size derived from natural sources, providing and laying cement concrete in retaining walls, return walls, walls any thickness including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing 1 2 4 1 cement 2 coarse sand zone iii derived from natural sources 4 graded stone aggregate 20 mm nominal size derived from natural sources, centering and shuttering including strutting, propping etc and removal of form work for foundations, footings, bases for columns foundations, footings, bases for columns, centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete, centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers, centering and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts, steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo mechanically treated bars of grade fe 500d or more., steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. thermo mechanically treated bars of grade fe 500d or more., providing and laying in position machine batched and machine mixed design mix m 25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer in charge. note cement content considered in this item is at the rate 330 kg per cum. excess or less cement used as per design mix is payable or recoverable separately all works upto plinth level, providing and laying in position machine batched and machine mixed design mix m 25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge. (note cement content considered in this item is at the rate 330 kg per cum. excess or less cement used as per design mix is payable or recoverable separately. all works above plinth level upto floor v level., add for using extra cement in the items of design mix over and above the specified cement content therein., brick work with common burnt clay f.p.s. non modular bricks of class designation 7.5 in foundation and plinth in cement mortar 1 6 1 cement 6 coarse sand, brick work with common burnt clay f.p.s. non modular bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in cement mortar 1 6 1 cement 6 coarse sand, 12 mm cement plaster of mix 1 6 1 cement 6 coarse sand, 15 mm cement plaster on rough side of single or half brick wall of mix 1 6 1 cement 6 coarse sand, finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade new work two or more coats applied at the rate 1.43 ltr per 10 sqm over and including priming coat of exterior primer applied at the rate 2.20 kg per10 sqm, applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron steel works, painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new work, providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length total length 90 m, having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron y shaped placed 2.4m or 3.00 m apart and with 9 horizontal r.b.t. reinforced barbed wire, stud tied with g.i. staples and g.i. clips to retain horizontal, including necessary bolts or g.i. barbed wire tied to angle iron, all complete as per direction of engineer in charge, with reinforced barbed tape r.b.t. spring core 2.5mm thick wire of high tensile strength of 165 kg per sq.mm with tape 0.52 mm thick and weight 43.478 gm per metre cost of m.s. angle, c.c. blocks shall be paid separately, supplying at site angle iron post and strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete., bidders should first download and review all available tender documents. These documents generally include the Notice Inviting Tender (NIT), Bill of Quantities (BOQ), technical specifications, eligibility criteria, scope of work, and bid submission instructions.


Tender Governemnt Authorities like Uranium Corporation Of India Limited UCIL usually publish these documents on their official eProcurement portals, departmental tender portals, the GeM Tender Portal, or other government procurement platforms or on newspapre. Finding and accessing the correct tender documents across multiple portals can sometimes be time-consuming for bidders. 


To make the process easier, Tender18 provides quick access to the available tender documents related to this Ghatshila , Jharkhand tender on a single page. Businesses involved in reinforced cement concrete,synthetic enamel paint,cement concrete work,zinc chromate primer,hydraulic excavator,steel reinforcement,synthetic enamel,cement concrete,retaining walls,concertina coil,angle iron post,exterior paint,boundary wall,concrete work,zinc chromate,enamel paint,punched tape,coarse sand,steel works,barbed wire,earth work,brick work,angle iron,red oxide,rcc work,ms angle,bricks,bolts related products, services, or works can conveniently download the relevant documents and review the tender requirements without spending time searching across different procurement portals.

The tender for title1 , title2 , title3 , title4 , title5 , title6 , title7 , title8 , title9 , title10 , title11 , title12 , title13 , title14 , title15 , title16 , title17 , title18 , title19 , title20 , title21 , title22 , title23, construction of boundary wall at aecs secondary at narwapahar mines, earth work in excavation by mechanical means hydraulic excavator manual means over areas exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by engineer in charge. all kind of soil, filling available excavated earth excluding rock in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.50m., clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50m outside the periphery of the area cleared., providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth levelshelves,chajja,lintel,band,plain window sills,stsiarcase and spiral stair case above plinth level upto floor five level execluding the cost of centering,shuttering,finishing and reinforced with 1 ratio 1.5 ratio 3 1 cement 1.5 coarse sand 3 graded stone aggregate. 1 5 10 1 cement 5 coarse sand zone iii derived from natural sources 10 graded stone aggregate 40 mm nominal size derived from natural sources, providing and laying cement concrete in retaining walls, return walls, walls any thickness including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing 1 2 4 1 cement 2 coarse sand zone iii derived from natural sources 4 graded stone aggregate 20 mm nominal size derived from natural sources, centering and shuttering including strutting, propping etc and removal of form work for foundations, footings, bases for columns foundations, footings, bases for columns, centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete, centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers, centering and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts, steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo mechanically treated bars of grade fe 500d or more., steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. thermo mechanically treated bars of grade fe 500d or more., providing and laying in position machine batched and machine mixed design mix m 25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer in charge. note cement content considered in this item is at the rate 330 kg per cum. excess or less cement used as per design mix is payable or recoverable separately all works upto plinth level, providing and laying in position machine batched and machine mixed design mix m 25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge. (note cement content considered in this item is at the rate 330 kg per cum. excess or less cement used as per design mix is payable or recoverable separately. all works above plinth level upto floor v level., add for using extra cement in the items of design mix over and above the specified cement content therein., brick work with common burnt clay f.p.s. non modular bricks of class designation 7.5 in foundation and plinth in cement mortar 1 6 1 cement 6 coarse sand, brick work with common burnt clay f.p.s. non modular bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in cement mortar 1 6 1 cement 6 coarse sand, 12 mm cement plaster of mix 1 6 1 cement 6 coarse sand, 15 mm cement plaster on rough side of single or half brick wall of mix 1 6 1 cement 6 coarse sand, finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade new work two or more coats applied at the rate 1.43 ltr per 10 sqm over and including priming coat of exterior primer applied at the rate 2.20 kg per10 sqm, applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron steel works, painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new work, providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length total length 90 m, having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron y shaped placed 2.4m or 3.00 m apart and with 9 horizontal r.b.t. reinforced barbed wire, stud tied with g.i. staples and g.i. clips to retain horizontal, including necessary bolts or g.i. barbed wire tied to angle iron, all complete as per direction of engineer in charge, with reinforced barbed tape r.b.t. spring core 2.5mm thick wire of high tensile strength of 165 kg per sq.mm with tape 0.52 mm thick and weight 43.478 gm per metre cost of m.s. angle, c.c. blocks shall be paid separately, supplying at site angle iron post and strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete. from Ghatshila, Jharkhand may be relevant for contractors, suppliers, vendors, manufacturers, consultants, service providers, startups, MSMEs, and other organizations involved in reinforced cement concrete,synthetic enamel paint,cement concrete work,zinc chromate primer,hydraulic excavator,steel reinforcement,synthetic enamel,cement concrete,retaining walls,concertina coil,angle iron post,exterior paint,boundary wall,concrete work,zinc chromate,enamel paint,punched tape,coarse sand,steel works,barbed wire,earth work,brick work,angle iron,red oxide,rcc work,ms angle,bricks,bolts related products, services, or works. However, eligibility to participate depends on the qualification criteria specified by Uranium Corporation Of India Limited UCIL in the official tender documents.

Before submitting a bid, interested applicants should carefully review the eligibility conditions, technical requirements, financial criteria, work experience requirements, annual turnover conditions, registrations, certifications, and any other supporting documents required by the tendering authority. The detailed qualification requirements and bidder eligibility criteria are available in the tender notice and related documents provided on this page. 

Ensuring compliance with all eligibility and qualification requirements before bid submission can help bidders avoid disqualification and improve their chances of successful participation in the tender process.

Tende18 provides comprehensive tender bidding services, including a complete tender summary along with a detailed analysis of the Tender Qualification and Eligibility Criteria.

Interested in participating in the tender for title1 , title2 , title3 , title4 , title5 , title6 , title7 , title8 , title9 , title10 , title11 , title12 , title13 , title14 , title15 , title16 , title17 , title18 , title19 , title20 , title21 , title22 , title23, construction of boundary wall at aecs secondary at narwapahar mines, earth work in excavation by mechanical means hydraulic excavator manual means over areas exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by engineer in charge. all kind of soil, filling available excavated earth excluding rock in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.50m., clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50m outside the periphery of the area cleared., providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth levelshelves,chajja,lintel,band,plain window sills,stsiarcase and spiral stair case above plinth level upto floor five level execluding the cost of centering,shuttering,finishing and reinforced with 1 ratio 1.5 ratio 3 1 cement 1.5 coarse sand 3 graded stone aggregate. 1 5 10 1 cement 5 coarse sand zone iii derived from natural sources 10 graded stone aggregate 40 mm nominal size derived from natural sources, providing and laying cement concrete in retaining walls, return walls, walls any thickness including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing 1 2 4 1 cement 2 coarse sand zone iii derived from natural sources 4 graded stone aggregate 20 mm nominal size derived from natural sources, centering and shuttering including strutting, propping etc and removal of form work for foundations, footings, bases for columns foundations, footings, bases for columns, centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete, centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers, centering and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts, steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo mechanically treated bars of grade fe 500d or more., steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. thermo mechanically treated bars of grade fe 500d or more., providing and laying in position machine batched and machine mixed design mix m 25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer in charge. note cement content considered in this item is at the rate 330 kg per cum. excess or less cement used as per design mix is payable or recoverable separately all works upto plinth level, providing and laying in position machine batched and machine mixed design mix m 25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge. (note cement content considered in this item is at the rate 330 kg per cum. excess or less cement used as per design mix is payable or recoverable separately. all works above plinth level upto floor v level., add for using extra cement in the items of design mix over and above the specified cement content therein., brick work with common burnt clay f.p.s. non modular bricks of class designation 7.5 in foundation and plinth in cement mortar 1 6 1 cement 6 coarse sand, brick work with common burnt clay f.p.s. non modular bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in cement mortar 1 6 1 cement 6 coarse sand, 12 mm cement plaster of mix 1 6 1 cement 6 coarse sand, 15 mm cement plaster on rough side of single or half brick wall of mix 1 6 1 cement 6 coarse sand, finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade new work two or more coats applied at the rate 1.43 ltr per 10 sqm over and including priming coat of exterior primer applied at the rate 2.20 kg per10 sqm, applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron steel works, painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new work, providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length total length 90 m, having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron y shaped placed 2.4m or 3.00 m apart and with 9 horizontal r.b.t. reinforced barbed wire, stud tied with g.i. staples and g.i. clips to retain horizontal, including necessary bolts or g.i. barbed wire tied to angle iron, all complete as per direction of engineer in charge, with reinforced barbed tape r.b.t. spring core 2.5mm thick wire of high tensile strength of 165 kg per sq.mm with tape 0.52 mm thick and weight 43.478 gm per metre cost of m.s. angle, c.c. blocks shall be paid separately, supplying at site angle iron post and strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete. issued by Uranium Corporation Of India Limited UCIL for reinforced cement concrete,synthetic enamel paint,cement concrete work,zinc chromate primer,hydraulic excavator,steel reinforcement,synthetic enamel,cement concrete,retaining walls,concertina coil,angle iron post,exterior paint,boundary wall,concrete work,zinc chromate,enamel paint,punched tape,coarse sand,steel works,barbed wire,earth work,brick work,angle iron,red oxide,rcc work,ms angle,bricks,bolts related work in Ghatshila, Jharkhand? TENDER18 provides complete assistance to help businesses understand tender requirements, access tender documents, review eligibility criteria, qualification requirements, important dates, and bid submission guidelines associated with this tender.

Our Tender18 Expert Technical team can assist with vendor and GeM registration on the relevant departmental, eProcurement, GeM, or government tender portal, preparation of technical and financial bid documents, compliance with qualification criteria, document verification, and complete online tender submission support. Whether you are a contractor, supplier, manufacturer, consultant, startup, or MSME working in the field of reinforced cement concrete,synthetic enamel paint,cement concrete work,zinc chromate primer,hydraulic excavator,steel reinforcement,synthetic enamel,cement concrete,retaining walls,concertina coil,angle iron post,exterior paint,boundary wall,concrete work,zinc chromate,enamel paint,punched tape,coarse sand,steel works,barbed wire,earth work,brick work,angle iron,red oxide,rcc work,ms angle,bricks,bolts, Tender18 can help simplify the tender participation process and support you throughout every stage of bidding for this tender. so that tender18 is one the top leading tender consultant in Inda.

1.

Whom should I contact if I have further queries about the Tender scope?

You can fill out the integrated inquiry form below on this detail page to share your company profile. Our consultancy desk will review your query regarding reinforced cement concrete,synthetic enamel paint,cement concrete work,zinc chromate primer,hydraulic excavator,steel reinforcement,synthetic enamel,cement concrete,retaining walls,concertina coil,angle iron post,exterior paint,boundary wall,concrete work,zinc chromate,enamel paint,punched tape,coarse sand,steel works,barbed wire,earth work,brick work,angle iron,red oxide,rcc work,ms angle,bricks,bolts parameters and guide you on how to coordinate efficiently with the procurement team of Uranium Corporation Of India Limited UCIL

2.

How can Tender18 assist my business in winning this government contract?

Tender18 provides end-to-end professional bidding support and documentation advisory for Tender For Title1 , Title2 , Title3 , Title4 , Title5 , Title6 , Title7 , Title8 , Title9 , Title10 , Title11 , Title12 , Title13 , Title14 , Title15 , Title16 , Title17 , Title18 , Title19 , Title20 , Title21 , Title22 , Title23, Construction Of Boundary Wall At Aecs Secondary At Narwapahar Mines, Earth Work In Excavation By Mechanical Means Hydraulic Excavator Manual Means Over Areas Exceeding 30 Cm In Depth, 1.5 M In Width As Well As 10 Sqm On Plan Including Getting Out And Disposal Of Excavated Earth Lead Up To 50 M And Lift Up To 1.5 M, As Directed By Engineer In Charge. All Kind Of Soil, Filling Available Excavated Earth Excluding Rock In Trenches, Plinth, Sides Of Foundations Etc. In Layers Not Exceeding 20cm In Depth, Consolidating Each Deposited Layer By Ramming And Watering Lead Upto 50m And Lift Upto 1.50m., Clearing Jungle Including Uprooting Of Rank Vegetation, Grass, Brush Wood, Trees And Saplings Of Girth Up To 30 Cm Measured At A Height Of 1 M Above Ground Level And Removal Of Rubbish Upto A Distance Of 50m Outside The Periphery Of The Area Cleared., Providing And Laying In Position Cement Concrete Of Specified Grade Excluding The Cost Of Centering And Shuttering All Work Up To Plinth Levelshelves,chajja,lintel,band,plain Window Sills,stsiarcase And Spiral Stair Case Above Plinth Level Upto Floor Five Level Execluding The Cost Of Centering,shuttering,finishing And Reinforced With 1 Ratio 1.5 Ratio 3 1 Cement 1.5 Coarse Sand 3 Graded Stone Aggregate. 1 5 10 1 Cement 5 Coarse Sand Zone Iii Derived From Natural Sources 10 Graded Stone Aggregate 40 Mm Nominal Size Derived From Natural Sources, Providing And Laying Cement Concrete In Retaining Walls, Return Walls, Walls Any Thickness Including Attached Pilasters, Columns, Piers, Abutments, Pillars, Posts, Struts, Buttresses, String Or Lacing Courses, Parapets, Coping, Bed Blocks, Anchor Blocks, Plain Window Sills, Fillets, Sunken Floor Etc., Up To Floor Five Level, Excluding The Cost Of Centering, Shuttering And Finishing 1 2 4 1 Cement 2 Coarse Sand Zone Iii Derived From Natural Sources 4 Graded Stone Aggregate 20 Mm Nominal Size Derived From Natural Sources, Centering And Shuttering Including Strutting, Propping Etc And Removal Of Form Work For Foundations, Footings, Bases For Columns Foundations, Footings, Bases For Columns, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Foundations, Footings, Bases Of Columns, Etc. For Mass Concrete, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Lintels, Beams, Plinth Beams, Girders, Bressumers And Cantilevers, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Columns, Pillars, Piers, Abutments, Posts And Struts, Steel Reinforcement For R.c.c. Work Including Straightening, Cutting, Bending, Placing In Position And Binding All Complete Upto Plinth Level. Thermo Mechanically Treated Bars Of Grade Fe 500d Or More., Steel Reinforcement For R.c.c. Work Including Straightening, Cutting, Bending, Placing In Position And Binding All Complete Above Plinth Level. Thermo Mechanically Treated Bars Of Grade Fe 500d Or More., Providing And Laying In Position Machine Batched And Machine Mixed Design Mix M 25 Grade Cement Concrete For Reinforced Cement Concrete Work, Using Cement Content As Per Approved Design Mix, Including Pumping Of Concrete To Site Of Laying But Excluding The Cost Of Centering, Shuttering, Finishing And Reinforcement, Including Admixtures In Recommended Proportions As Per Is 9103 To Accelerate, Retard Setting Of Concrete, Improve Workability Without Impairing Strength And Durability As Per Direction Of Engineer In Charge. Note Cement Content Considered In This Item Is At The Rate 330 Kg Per Cum. Excess Or Less Cement Used As Per Design Mix Is Payable Or Recoverable Separately All Works Upto Plinth Level, Providing And Laying In Position Machine Batched And Machine Mixed Design Mix M 25 Grade Cement Concrete For Reinforced Cement Concrete Work, Using Cement Content As Per Approved Design Mix, Including Pumping Of Concrete To Site Of Laying But Excluding The Cost Of Centering, Shuttering, Finishing And Reinforcement, Including Admixtures In Recommended Proportions As Per Is 9103 To Accelerate, Retard Setting Of Concrete, Improve Workability Without Impairing Strength And Durability As Per Direction Of Engineer-in-charge. (note Cement Content Considered In This Item Is At The Rate 330 Kg Per Cum. Excess Or Less Cement Used As Per Design Mix Is Payable Or Recoverable Separately. All Works Above Plinth Level Upto Floor V Level., Add For Using Extra Cement In The Items Of Design Mix Over And Above The Specified Cement Content Therein., Brick Work With Common Burnt Clay F.p.s. Non Modular Bricks Of Class Designation 7.5 In Foundation And Plinth In Cement Mortar 1 6 1 Cement 6 Coarse Sand, Brick Work With Common Burnt Clay F.p.s. Non Modular Bricks Of Class Designation 7.5 In Superstructure Above Plinth Level Up To Floor V Level In All Shapes And Sizes In Cement Mortar 1 6 1 Cement 6 Coarse Sand, 12 Mm Cement Plaster Of Mix 1 6 1 Cement 6 Coarse Sand, 15 Mm Cement Plaster On Rough Side Of Single Or Half Brick Wall Of Mix 1 6 1 Cement 6 Coarse Sand, Finishing Walls With Premium Acrylic Smooth Exterior Paint With Silicone Additives Of Required Shade New Work Two Or More Coats Applied At The Rate 1.43 Ltr Per 10 Sqm Over And Including Priming Coat Of Exterior Primer Applied At The Rate 2.20 Kg Per10 Sqm, Applying Priming Coat With Ready Mixed Red Oxide Zinc Chromate Primer Of Approved Brand And Manufacture On Steel Galvanised Iron Steel Works, Painting With Synthetic Enamel Paint Of Approved Brand And Manufacture To Give An Even Shade Two Or More Coats On New Work, Providing And Fixing Concertina Coil Fencing With Punched Tape Concertina Coil 600 Mm Dia 10 Metre Openable Length Total Length 90 M, Having 50 Nos Rounds Per 6 Metre Length, Upto 3 M Height Of Wall With Existing Angle Iron Y Shaped Placed 2.4m Or 3.00 M Apart And With 9 Horizontal R.b.t. Reinforced Barbed Wire, Stud Tied With G.i. Staples And G.i. Clips To Retain Horizontal, Including Necessary Bolts Or G.i. Barbed Wire Tied To Angle Iron, All Complete As Per Direction Of Engineer In Charge, With Reinforced Barbed Tape R.b.t. Spring Core 2.5mm Thick Wire Of High Tensile Strength Of 165 Kg Per Sq.mm With Tape 0.52 Mm Thick And Weight 43.478 Gm Per Metre Cost Of M.s. Angle, C.c. Blocks Shall Be Paid Separately, Supplying At Site Angle Iron Post And Strut Of Required Size Including Bottom To Be Split And Bent At Right Angle In Opposite Direction For 10 Cm Length And Drilling Holes Upto 10 Mm Dia. Etc. Complete. . Our senior analysts help you decode the complete project guidelines, manage accurate costing sheets, and complete error-free submissions on the official platform used by Uranium Corporation Of India Limited UCIL.

3.

What are the main reasons for a technical tender rejection?

Most online bids face rejection during the initial evaluation round due to avoidable errors like uploading blurred document scans, submitting expired DSCs, or missing critical experience papers required for Tender For Title1 , Title2 , Title3 , Title4 , Title5 , Title6 , Title7 , Title8 , Title9 , Title10 , Title11 , Title12 , Title13 , Title14 , Title15 , Title16 , Title17 , Title18 , Title19 , Title20 , Title21 , Title22 , Title23, Construction Of Boundary Wall At Aecs Secondary At Narwapahar Mines, Earth Work In Excavation By Mechanical Means Hydraulic Excavator Manual Means Over Areas Exceeding 30 Cm In Depth, 1.5 M In Width As Well As 10 Sqm On Plan Including Getting Out And Disposal Of Excavated Earth Lead Up To 50 M And Lift Up To 1.5 M, As Directed By Engineer In Charge. All Kind Of Soil, Filling Available Excavated Earth Excluding Rock In Trenches, Plinth, Sides Of Foundations Etc. In Layers Not Exceeding 20cm In Depth, Consolidating Each Deposited Layer By Ramming And Watering Lead Upto 50m And Lift Upto 1.50m., Clearing Jungle Including Uprooting Of Rank Vegetation, Grass, Brush Wood, Trees And Saplings Of Girth Up To 30 Cm Measured At A Height Of 1 M Above Ground Level And Removal Of Rubbish Upto A Distance Of 50m Outside The Periphery Of The Area Cleared., Providing And Laying In Position Cement Concrete Of Specified Grade Excluding The Cost Of Centering And Shuttering All Work Up To Plinth Levelshelves,chajja,lintel,band,plain Window Sills,stsiarcase And Spiral Stair Case Above Plinth Level Upto Floor Five Level Execluding The Cost Of Centering,shuttering,finishing And Reinforced With 1 Ratio 1.5 Ratio 3 1 Cement 1.5 Coarse Sand 3 Graded Stone Aggregate. 1 5 10 1 Cement 5 Coarse Sand Zone Iii Derived From Natural Sources 10 Graded Stone Aggregate 40 Mm Nominal Size Derived From Natural Sources, Providing And Laying Cement Concrete In Retaining Walls, Return Walls, Walls Any Thickness Including Attached Pilasters, Columns, Piers, Abutments, Pillars, Posts, Struts, Buttresses, String Or Lacing Courses, Parapets, Coping, Bed Blocks, Anchor Blocks, Plain Window Sills, Fillets, Sunken Floor Etc., Up To Floor Five Level, Excluding The Cost Of Centering, Shuttering And Finishing 1 2 4 1 Cement 2 Coarse Sand Zone Iii Derived From Natural Sources 4 Graded Stone Aggregate 20 Mm Nominal Size Derived From Natural Sources, Centering And Shuttering Including Strutting, Propping Etc And Removal Of Form Work For Foundations, Footings, Bases For Columns Foundations, Footings, Bases For Columns, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Foundations, Footings, Bases Of Columns, Etc. For Mass Concrete, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Lintels, Beams, Plinth Beams, Girders, Bressumers And Cantilevers, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Columns, Pillars, Piers, Abutments, Posts And Struts, Steel Reinforcement For R.c.c. Work Including Straightening, Cutting, Bending, Placing In Position And Binding All Complete Upto Plinth Level. Thermo Mechanically Treated Bars Of Grade Fe 500d Or More., Steel Reinforcement For R.c.c. Work Including Straightening, Cutting, Bending, Placing In Position And Binding All Complete Above Plinth Level. Thermo Mechanically Treated Bars Of Grade Fe 500d Or More., Providing And Laying In Position Machine Batched And Machine Mixed Design Mix M 25 Grade Cement Concrete For Reinforced Cement Concrete Work, Using Cement Content As Per Approved Design Mix, Including Pumping Of Concrete To Site Of Laying But Excluding The Cost Of Centering, Shuttering, Finishing And Reinforcement, Including Admixtures In Recommended Proportions As Per Is 9103 To Accelerate, Retard Setting Of Concrete, Improve Workability Without Impairing Strength And Durability As Per Direction Of Engineer In Charge. Note Cement Content Considered In This Item Is At The Rate 330 Kg Per Cum. Excess Or Less Cement Used As Per Design Mix Is Payable Or Recoverable Separately All Works Upto Plinth Level, Providing And Laying In Position Machine Batched And Machine Mixed Design Mix M 25 Grade Cement Concrete For Reinforced Cement Concrete Work, Using Cement Content As Per Approved Design Mix, Including Pumping Of Concrete To Site Of Laying But Excluding The Cost Of Centering, Shuttering, Finishing And Reinforcement, Including Admixtures In Recommended Proportions As Per Is 9103 To Accelerate, Retard Setting Of Concrete, Improve Workability Without Impairing Strength And Durability As Per Direction Of Engineer-in-charge. (note Cement Content Considered In This Item Is At The Rate 330 Kg Per Cum. Excess Or Less Cement Used As Per Design Mix Is Payable Or Recoverable Separately. All Works Above Plinth Level Upto Floor V Level., Add For Using Extra Cement In The Items Of Design Mix Over And Above The Specified Cement Content Therein., Brick Work With Common Burnt Clay F.p.s. Non Modular Bricks Of Class Designation 7.5 In Foundation And Plinth In Cement Mortar 1 6 1 Cement 6 Coarse Sand, Brick Work With Common Burnt Clay F.p.s. Non Modular Bricks Of Class Designation 7.5 In Superstructure Above Plinth Level Up To Floor V Level In All Shapes And Sizes In Cement Mortar 1 6 1 Cement 6 Coarse Sand, 12 Mm Cement Plaster Of Mix 1 6 1 Cement 6 Coarse Sand, 15 Mm Cement Plaster On Rough Side Of Single Or Half Brick Wall Of Mix 1 6 1 Cement 6 Coarse Sand, Finishing Walls With Premium Acrylic Smooth Exterior Paint With Silicone Additives Of Required Shade New Work Two Or More Coats Applied At The Rate 1.43 Ltr Per 10 Sqm Over And Including Priming Coat Of Exterior Primer Applied At The Rate 2.20 Kg Per10 Sqm, Applying Priming Coat With Ready Mixed Red Oxide Zinc Chromate Primer Of Approved Brand And Manufacture On Steel Galvanised Iron Steel Works, Painting With Synthetic Enamel Paint Of Approved Brand And Manufacture To Give An Even Shade Two Or More Coats On New Work, Providing And Fixing Concertina Coil Fencing With Punched Tape Concertina Coil 600 Mm Dia 10 Metre Openable Length Total Length 90 M, Having 50 Nos Rounds Per 6 Metre Length, Upto 3 M Height Of Wall With Existing Angle Iron Y Shaped Placed 2.4m Or 3.00 M Apart And With 9 Horizontal R.b.t. Reinforced Barbed Wire, Stud Tied With G.i. Staples And G.i. Clips To Retain Horizontal, Including Necessary Bolts Or G.i. Barbed Wire Tied To Angle Iron, All Complete As Per Direction Of Engineer In Charge, With Reinforced Barbed Tape R.b.t. Spring Core 2.5mm Thick Wire Of High Tensile Strength Of 165 Kg Per Sq.mm With Tape 0.52 Mm Thick And Weight 43.478 Gm Per Metre Cost Of M.s. Angle, C.c. Blocks Shall Be Paid Separately, Supplying At Site Angle Iron Post And Strut Of Required Size Including Bottom To Be Split And Bent At Right Angle In Opposite Direction For 10 Cm Length And Drilling Holes Upto 10 Mm Dia. Etc. Complete. in Jharkhand.

4.

Can contractors located outside the local region participate in this bid?

Eligibility for outstation bidders depends entirely on the terms set inside the document for Tender For Title1 , Title2 , Title3 , Title4 , Title5 , Title6 , Title7 , Title8 , Title9 , Title10 , Title11 , Title12 , Title13 , Title14 , Title15 , Title16 , Title17 , Title18 , Title19 , Title20 , Title21 , Title22 , Title23, Construction Of Boundary Wall At Aecs Secondary At Narwapahar Mines, Earth Work In Excavation By Mechanical Means Hydraulic Excavator Manual Means Over Areas Exceeding 30 Cm In Depth, 1.5 M In Width As Well As 10 Sqm On Plan Including Getting Out And Disposal Of Excavated Earth Lead Up To 50 M And Lift Up To 1.5 M, As Directed By Engineer In Charge. All Kind Of Soil, Filling Available Excavated Earth Excluding Rock In Trenches, Plinth, Sides Of Foundations Etc. In Layers Not Exceeding 20cm In Depth, Consolidating Each Deposited Layer By Ramming And Watering Lead Upto 50m And Lift Upto 1.50m., Clearing Jungle Including Uprooting Of Rank Vegetation, Grass, Brush Wood, Trees And Saplings Of Girth Up To 30 Cm Measured At A Height Of 1 M Above Ground Level And Removal Of Rubbish Upto A Distance Of 50m Outside The Periphery Of The Area Cleared., Providing And Laying In Position Cement Concrete Of Specified Grade Excluding The Cost Of Centering And Shuttering All Work Up To Plinth Levelshelves,chajja,lintel,band,plain Window Sills,stsiarcase And Spiral Stair Case Above Plinth Level Upto Floor Five Level Execluding The Cost Of Centering,shuttering,finishing And Reinforced With 1 Ratio 1.5 Ratio 3 1 Cement 1.5 Coarse Sand 3 Graded Stone Aggregate. 1 5 10 1 Cement 5 Coarse Sand Zone Iii Derived From Natural Sources 10 Graded Stone Aggregate 40 Mm Nominal Size Derived From Natural Sources, Providing And Laying Cement Concrete In Retaining Walls, Return Walls, Walls Any Thickness Including Attached Pilasters, Columns, Piers, Abutments, Pillars, Posts, Struts, Buttresses, String Or Lacing Courses, Parapets, Coping, Bed Blocks, Anchor Blocks, Plain Window Sills, Fillets, Sunken Floor Etc., Up To Floor Five Level, Excluding The Cost Of Centering, Shuttering And Finishing 1 2 4 1 Cement 2 Coarse Sand Zone Iii Derived From Natural Sources 4 Graded Stone Aggregate 20 Mm Nominal Size Derived From Natural Sources, Centering And Shuttering Including Strutting, Propping Etc And Removal Of Form Work For Foundations, Footings, Bases For Columns Foundations, Footings, Bases For Columns, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Foundations, Footings, Bases Of Columns, Etc. For Mass Concrete, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Lintels, Beams, Plinth Beams, Girders, Bressumers And Cantilevers, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Columns, Pillars, Piers, Abutments, Posts And Struts, Steel Reinforcement For R.c.c. Work Including Straightening, Cutting, Bending, Placing In Position And Binding All Complete Upto Plinth Level. Thermo Mechanically Treated Bars Of Grade Fe 500d Or More., Steel Reinforcement For R.c.c. Work Including Straightening, Cutting, Bending, Placing In Position And Binding All Complete Above Plinth Level. Thermo Mechanically Treated Bars Of Grade Fe 500d Or More., Providing And Laying In Position Machine Batched And Machine Mixed Design Mix M 25 Grade Cement Concrete For Reinforced Cement Concrete Work, Using Cement Content As Per Approved Design Mix, Including Pumping Of Concrete To Site Of Laying But Excluding The Cost Of Centering, Shuttering, Finishing And Reinforcement, Including Admixtures In Recommended Proportions As Per Is 9103 To Accelerate, Retard Setting Of Concrete, Improve Workability Without Impairing Strength And Durability As Per Direction Of Engineer In Charge. Note Cement Content Considered In This Item Is At The Rate 330 Kg Per Cum. Excess Or Less Cement Used As Per Design Mix Is Payable Or Recoverable Separately All Works Upto Plinth Level, Providing And Laying In Position Machine Batched And Machine Mixed Design Mix M 25 Grade Cement Concrete For Reinforced Cement Concrete Work, Using Cement Content As Per Approved Design Mix, Including Pumping Of Concrete To Site Of Laying But Excluding The Cost Of Centering, Shuttering, Finishing And Reinforcement, Including Admixtures In Recommended Proportions As Per Is 9103 To Accelerate, Retard Setting Of Concrete, Improve Workability Without Impairing Strength And Durability As Per Direction Of Engineer-in-charge. (note Cement Content Considered In This Item Is At The Rate 330 Kg Per Cum. Excess Or Less Cement Used As Per Design Mix Is Payable Or Recoverable Separately. All Works Above Plinth Level Upto Floor V Level., Add For Using Extra Cement In The Items Of Design Mix Over And Above The Specified Cement Content Therein., Brick Work With Common Burnt Clay F.p.s. Non Modular Bricks Of Class Designation 7.5 In Foundation And Plinth In Cement Mortar 1 6 1 Cement 6 Coarse Sand, Brick Work With Common Burnt Clay F.p.s. Non Modular Bricks Of Class Designation 7.5 In Superstructure Above Plinth Level Up To Floor V Level In All Shapes And Sizes In Cement Mortar 1 6 1 Cement 6 Coarse Sand, 12 Mm Cement Plaster Of Mix 1 6 1 Cement 6 Coarse Sand, 15 Mm Cement Plaster On Rough Side Of Single Or Half Brick Wall Of Mix 1 6 1 Cement 6 Coarse Sand, Finishing Walls With Premium Acrylic Smooth Exterior Paint With Silicone Additives Of Required Shade New Work Two Or More Coats Applied At The Rate 1.43 Ltr Per 10 Sqm Over And Including Priming Coat Of Exterior Primer Applied At The Rate 2.20 Kg Per10 Sqm, Applying Priming Coat With Ready Mixed Red Oxide Zinc Chromate Primer Of Approved Brand And Manufacture On Steel Galvanised Iron Steel Works, Painting With Synthetic Enamel Paint Of Approved Brand And Manufacture To Give An Even Shade Two Or More Coats On New Work, Providing And Fixing Concertina Coil Fencing With Punched Tape Concertina Coil 600 Mm Dia 10 Metre Openable Length Total Length 90 M, Having 50 Nos Rounds Per 6 Metre Length, Upto 3 M Height Of Wall With Existing Angle Iron Y Shaped Placed 2.4m Or 3.00 M Apart And With 9 Horizontal R.b.t. Reinforced Barbed Wire, Stud Tied With G.i. Staples And G.i. Clips To Retain Horizontal, Including Necessary Bolts Or G.i. Barbed Wire Tied To Angle Iron, All Complete As Per Direction Of Engineer In Charge, With Reinforced Barbed Tape R.b.t. Spring Core 2.5mm Thick Wire Of High Tensile Strength Of 165 Kg Per Sq.mm With Tape 0.52 Mm Thick And Weight 43.478 Gm Per Metre Cost Of M.s. Angle, C.c. Blocks Shall Be Paid Separately, Supplying At Site Angle Iron Post And Strut Of Required Size Including Bottom To Be Split And Bent At Right Angle In Opposite Direction For 10 Cm Length And Drilling Holes Upto 10 Mm Dia. Etc. Complete.. While many public sector projects allow national competitive bidding, certain localized works require local offices or specific registration metrics in Ghatshila.

5.

Do I need an active GeM Portal registration to apply for this work?

If this procurement is routed through the central marketplace, an active GeM Seller ID is mandatory to supply reinforced cement concrete,synthetic enamel paint,cement concrete work,zinc chromate primer,hydraulic excavator,steel reinforcement,synthetic enamel,cement concrete,retaining walls,concertina coil,angle iron post,exterior paint,boundary wall,concrete work,zinc chromate,enamel paint,punched tape,coarse sand,steel works,barbed wire,earth work,brick work,angle iron,red oxide,rcc work,ms angle,bricks,bolts items. Tender18 offers complete assistance for brand cataloging, profile creation, and vendor assessment required officially by Uranium Corporation Of India Limited UCIL

6.

What are the primary legal documents required to submit a valid bid?

To register an eligible bid for these reinforced cement concrete,synthetic enamel paint,cement concrete work,zinc chromate primer,hydraulic excavator,steel reinforcement,synthetic enamel,cement concrete,retaining walls,concertina coil,angle iron post,exterior paint,boundary wall,concrete work,zinc chromate,enamel paint,punched tape,coarse sand,steel works,barbed wire,earth work,brick work,angle iron,red oxide,rcc work,ms angle,bricks,bolts contracts, companies must prepare their core compliance documents. Vendors operating across Jharkhand must ensure they possess a valid GST registration, permanent account number (PAN), and active Class-3 Digital Signature Certificates.

7.

What products or services are required for this active work?

This public procurement cycle is specifically looking for qualified vendors and suppliers who can provide high-quality reinforced cement concrete,synthetic enamel paint,cement concrete work,zinc chromate primer,hydraulic excavator,steel reinforcement,synthetic enamel,cement concrete,retaining walls,concertina coil,angle iron post,exterior paint,boundary wall,concrete work,zinc chromate,enamel paint,punched tape,coarse sand,steel works,barbed wire,earth work,brick work,angle iron,red oxide,rcc work,ms angle,bricks,bolts solutions. The operational execution, delivery, and deployment of these materials must be managed locally within the Ghatshila region.

8.

Where can I review the estimated cost or budget details for this Tender?

The estimated project cost and budget thresholds can be reviewed directly inside the tender document. Bidders can analyze these qualification files to check if their firm meets the financial capability criteria specified for Tender For Title1 , Title2 , Title3 , Title4 , Title5 , Title6 , Title7 , Title8 , Title9 , Title10 , Title11 , Title12 , Title13 , Title14 , Title15 , Title16 , Title17 , Title18 , Title19 , Title20 , Title21 , Title22 , Title23, Construction Of Boundary Wall At Aecs Secondary At Narwapahar Mines, Earth Work In Excavation By Mechanical Means Hydraulic Excavator Manual Means Over Areas Exceeding 30 Cm In Depth, 1.5 M In Width As Well As 10 Sqm On Plan Including Getting Out And Disposal Of Excavated Earth Lead Up To 50 M And Lift Up To 1.5 M, As Directed By Engineer In Charge. All Kind Of Soil, Filling Available Excavated Earth Excluding Rock In Trenches, Plinth, Sides Of Foundations Etc. In Layers Not Exceeding 20cm In Depth, Consolidating Each Deposited Layer By Ramming And Watering Lead Upto 50m And Lift Upto 1.50m., Clearing Jungle Including Uprooting Of Rank Vegetation, Grass, Brush Wood, Trees And Saplings Of Girth Up To 30 Cm Measured At A Height Of 1 M Above Ground Level And Removal Of Rubbish Upto A Distance Of 50m Outside The Periphery Of The Area Cleared., Providing And Laying In Position Cement Concrete Of Specified Grade Excluding The Cost Of Centering And Shuttering All Work Up To Plinth Levelshelves,chajja,lintel,band,plain Window Sills,stsiarcase And Spiral Stair Case Above Plinth Level Upto Floor Five Level Execluding The Cost Of Centering,shuttering,finishing And Reinforced With 1 Ratio 1.5 Ratio 3 1 Cement 1.5 Coarse Sand 3 Graded Stone Aggregate. 1 5 10 1 Cement 5 Coarse Sand Zone Iii Derived From Natural Sources 10 Graded Stone Aggregate 40 Mm Nominal Size Derived From Natural Sources, Providing And Laying Cement Concrete In Retaining Walls, Return Walls, Walls Any Thickness Including Attached Pilasters, Columns, Piers, Abutments, Pillars, Posts, Struts, Buttresses, String Or Lacing Courses, Parapets, Coping, Bed Blocks, Anchor Blocks, Plain Window Sills, Fillets, Sunken Floor Etc., Up To Floor Five Level, Excluding The Cost Of Centering, Shuttering And Finishing 1 2 4 1 Cement 2 Coarse Sand Zone Iii Derived From Natural Sources 4 Graded Stone Aggregate 20 Mm Nominal Size Derived From Natural Sources, Centering And Shuttering Including Strutting, Propping Etc And Removal Of Form Work For Foundations, Footings, Bases For Columns Foundations, Footings, Bases For Columns, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Foundations, Footings, Bases Of Columns, Etc. For Mass Concrete, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Lintels, Beams, Plinth Beams, Girders, Bressumers And Cantilevers, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Columns, Pillars, Piers, Abutments, Posts And Struts, Steel Reinforcement For R.c.c. Work Including Straightening, Cutting, Bending, Placing In Position And Binding All Complete Upto Plinth Level. Thermo Mechanically Treated Bars Of Grade Fe 500d Or More., Steel Reinforcement For R.c.c. Work Including Straightening, Cutting, Bending, Placing In Position And Binding All Complete Above Plinth Level. Thermo Mechanically Treated Bars Of Grade Fe 500d Or More., Providing And Laying In Position Machine Batched And Machine Mixed Design Mix M 25 Grade Cement Concrete For Reinforced Cement Concrete Work, Using Cement Content As Per Approved Design Mix, Including Pumping Of Concrete To Site Of Laying But Excluding The Cost Of Centering, Shuttering, Finishing And Reinforcement, Including Admixtures In Recommended Proportions As Per Is 9103 To Accelerate, Retard Setting Of Concrete, Improve Workability Without Impairing Strength And Durability As Per Direction Of Engineer In Charge. Note Cement Content Considered In This Item Is At The Rate 330 Kg Per Cum. Excess Or Less Cement Used As Per Design Mix Is Payable Or Recoverable Separately All Works Upto Plinth Level, Providing And Laying In Position Machine Batched And Machine Mixed Design Mix M 25 Grade Cement Concrete For Reinforced Cement Concrete Work, Using Cement Content As Per Approved Design Mix, Including Pumping Of Concrete To Site Of Laying But Excluding The Cost Of Centering, Shuttering, Finishing And Reinforcement, Including Admixtures In Recommended Proportions As Per Is 9103 To Accelerate, Retard Setting Of Concrete, Improve Workability Without Impairing Strength And Durability As Per Direction Of Engineer-in-charge. (note Cement Content Considered In This Item Is At The Rate 330 Kg Per Cum. Excess Or Less Cement Used As Per Design Mix Is Payable Or Recoverable Separately. All Works Above Plinth Level Upto Floor V Level., Add For Using Extra Cement In The Items Of Design Mix Over And Above The Specified Cement Content Therein., Brick Work With Common Burnt Clay F.p.s. Non Modular Bricks Of Class Designation 7.5 In Foundation And Plinth In Cement Mortar 1 6 1 Cement 6 Coarse Sand, Brick Work With Common Burnt Clay F.p.s. Non Modular Bricks Of Class Designation 7.5 In Superstructure Above Plinth Level Up To Floor V Level In All Shapes And Sizes In Cement Mortar 1 6 1 Cement 6 Coarse Sand, 12 Mm Cement Plaster Of Mix 1 6 1 Cement 6 Coarse Sand, 15 Mm Cement Plaster On Rough Side Of Single Or Half Brick Wall Of Mix 1 6 1 Cement 6 Coarse Sand, Finishing Walls With Premium Acrylic Smooth Exterior Paint With Silicone Additives Of Required Shade New Work Two Or More Coats Applied At The Rate 1.43 Ltr Per 10 Sqm Over And Including Priming Coat Of Exterior Primer Applied At The Rate 2.20 Kg Per10 Sqm, Applying Priming Coat With Ready Mixed Red Oxide Zinc Chromate Primer Of Approved Brand And Manufacture On Steel Galvanised Iron Steel Works, Painting With Synthetic Enamel Paint Of Approved Brand And Manufacture To Give An Even Shade Two Or More Coats On New Work, Providing And Fixing Concertina Coil Fencing With Punched Tape Concertina Coil 600 Mm Dia 10 Metre Openable Length Total Length 90 M, Having 50 Nos Rounds Per 6 Metre Length, Upto 3 M Height Of Wall With Existing Angle Iron Y Shaped Placed 2.4m Or 3.00 M Apart And With 9 Horizontal R.b.t. Reinforced Barbed Wire, Stud Tied With G.i. Staples And G.i. Clips To Retain Horizontal, Including Necessary Bolts Or G.i. Barbed Wire Tied To Angle Iron, All Complete As Per Direction Of Engineer In Charge, With Reinforced Barbed Tape R.b.t. Spring Core 2.5mm Thick Wire Of High Tensile Strength Of 165 Kg Per Sq.mm With Tape 0.52 Mm Thick And Weight 43.478 Gm Per Metre Cost Of M.s. Angle, C.c. Blocks Shall Be Paid Separately, Supplying At Site Angle Iron Post And Strut Of Required Size Including Bottom To Be Split And Bent At Right Angle In Opposite Direction For 10 Cm Length And Drilling Holes Upto 10 Mm Dia. Etc. Complete. by Uranium Corporation Of India Limited UCIL

9.

How can I download the official BOQ file for this opportunity?

You can download the commercial Bill of Quantities (BOQ) spreadsheet directly using the secure link provided on this page. The BOQ file contains the item descriptions and rate filling forms officially validated for Tender For Title1 , Title2 , Title3 , Title4 , Title5 , Title6 , Title7 , Title8 , Title9 , Title10 , Title11 , Title12 , Title13 , Title14 , Title15 , Title16 , Title17 , Title18 , Title19 , Title20 , Title21 , Title22 , Title23, Construction Of Boundary Wall At Aecs Secondary At Narwapahar Mines, Earth Work In Excavation By Mechanical Means Hydraulic Excavator Manual Means Over Areas Exceeding 30 Cm In Depth, 1.5 M In Width As Well As 10 Sqm On Plan Including Getting Out And Disposal Of Excavated Earth Lead Up To 50 M And Lift Up To 1.5 M, As Directed By Engineer In Charge. All Kind Of Soil, Filling Available Excavated Earth Excluding Rock In Trenches, Plinth, Sides Of Foundations Etc. In Layers Not Exceeding 20cm In Depth, Consolidating Each Deposited Layer By Ramming And Watering Lead Upto 50m And Lift Upto 1.50m., Clearing Jungle Including Uprooting Of Rank Vegetation, Grass, Brush Wood, Trees And Saplings Of Girth Up To 30 Cm Measured At A Height Of 1 M Above Ground Level And Removal Of Rubbish Upto A Distance Of 50m Outside The Periphery Of The Area Cleared., Providing And Laying In Position Cement Concrete Of Specified Grade Excluding The Cost Of Centering And Shuttering All Work Up To Plinth Levelshelves,chajja,lintel,band,plain Window Sills,stsiarcase And Spiral Stair Case Above Plinth Level Upto Floor Five Level Execluding The Cost Of Centering,shuttering,finishing And Reinforced With 1 Ratio 1.5 Ratio 3 1 Cement 1.5 Coarse Sand 3 Graded Stone Aggregate. 1 5 10 1 Cement 5 Coarse Sand Zone Iii Derived From Natural Sources 10 Graded Stone Aggregate 40 Mm Nominal Size Derived From Natural Sources, Providing And Laying Cement Concrete In Retaining Walls, Return Walls, Walls Any Thickness Including Attached Pilasters, Columns, Piers, Abutments, Pillars, Posts, Struts, Buttresses, String Or Lacing Courses, Parapets, Coping, Bed Blocks, Anchor Blocks, Plain Window Sills, Fillets, Sunken Floor Etc., Up To Floor Five Level, Excluding The Cost Of Centering, Shuttering And Finishing 1 2 4 1 Cement 2 Coarse Sand Zone Iii Derived From Natural Sources 4 Graded Stone Aggregate 20 Mm Nominal Size Derived From Natural Sources, Centering And Shuttering Including Strutting, Propping Etc And Removal Of Form Work For Foundations, Footings, Bases For Columns Foundations, Footings, Bases For Columns, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Foundations, Footings, Bases Of Columns, Etc. For Mass Concrete, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Lintels, Beams, Plinth Beams, Girders, Bressumers And Cantilevers, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Columns, Pillars, Piers, Abutments, Posts And Struts, Steel Reinforcement For R.c.c. Work Including Straightening, Cutting, Bending, Placing In Position And Binding All Complete Upto Plinth Level. Thermo Mechanically Treated Bars Of Grade Fe 500d Or More., Steel Reinforcement For R.c.c. Work Including Straightening, Cutting, Bending, Placing In Position And Binding All Complete Above Plinth Level. Thermo Mechanically Treated Bars Of Grade Fe 500d Or More., Providing And Laying In Position Machine Batched And Machine Mixed Design Mix M 25 Grade Cement Concrete For Reinforced Cement Concrete Work, Using Cement Content As Per Approved Design Mix, Including Pumping Of Concrete To Site Of Laying But Excluding The Cost Of Centering, Shuttering, Finishing And Reinforcement, Including Admixtures In Recommended Proportions As Per Is 9103 To Accelerate, Retard Setting Of Concrete, Improve Workability Without Impairing Strength And Durability As Per Direction Of Engineer In Charge. Note Cement Content Considered In This Item Is At The Rate 330 Kg Per Cum. Excess Or Less Cement Used As Per Design Mix Is Payable Or Recoverable Separately All Works Upto Plinth Level, Providing And Laying In Position Machine Batched And Machine Mixed Design Mix M 25 Grade Cement Concrete For Reinforced Cement Concrete Work, Using Cement Content As Per Approved Design Mix, Including Pumping Of Concrete To Site Of Laying But Excluding The Cost Of Centering, Shuttering, Finishing And Reinforcement, Including Admixtures In Recommended Proportions As Per Is 9103 To Accelerate, Retard Setting Of Concrete, Improve Workability Without Impairing Strength And Durability As Per Direction Of Engineer-in-charge. (note Cement Content Considered In This Item Is At The Rate 330 Kg Per Cum. Excess Or Less Cement Used As Per Design Mix Is Payable Or Recoverable Separately. All Works Above Plinth Level Upto Floor V Level., Add For Using Extra Cement In The Items Of Design Mix Over And Above The Specified Cement Content Therein., Brick Work With Common Burnt Clay F.p.s. Non Modular Bricks Of Class Designation 7.5 In Foundation And Plinth In Cement Mortar 1 6 1 Cement 6 Coarse Sand, Brick Work With Common Burnt Clay F.p.s. Non Modular Bricks Of Class Designation 7.5 In Superstructure Above Plinth Level Up To Floor V Level In All Shapes And Sizes In Cement Mortar 1 6 1 Cement 6 Coarse Sand, 12 Mm Cement Plaster Of Mix 1 6 1 Cement 6 Coarse Sand, 15 Mm Cement Plaster On Rough Side Of Single Or Half Brick Wall Of Mix 1 6 1 Cement 6 Coarse Sand, Finishing Walls With Premium Acrylic Smooth Exterior Paint With Silicone Additives Of Required Shade New Work Two Or More Coats Applied At The Rate 1.43 Ltr Per 10 Sqm Over And Including Priming Coat Of Exterior Primer Applied At The Rate 2.20 Kg Per10 Sqm, Applying Priming Coat With Ready Mixed Red Oxide Zinc Chromate Primer Of Approved Brand And Manufacture On Steel Galvanised Iron Steel Works, Painting With Synthetic Enamel Paint Of Approved Brand And Manufacture To Give An Even Shade Two Or More Coats On New Work, Providing And Fixing Concertina Coil Fencing With Punched Tape Concertina Coil 600 Mm Dia 10 Metre Openable Length Total Length 90 M, Having 50 Nos Rounds Per 6 Metre Length, Upto 3 M Height Of Wall With Existing Angle Iron Y Shaped Placed 2.4m Or 3.00 M Apart And With 9 Horizontal R.b.t. Reinforced Barbed Wire, Stud Tied With G.i. Staples And G.i. Clips To Retain Horizontal, Including Necessary Bolts Or G.i. Barbed Wire Tied To Angle Iron, All Complete As Per Direction Of Engineer In Charge, With Reinforced Barbed Tape R.b.t. Spring Core 2.5mm Thick Wire Of High Tensile Strength Of 165 Kg Per Sq.mm With Tape 0.52 Mm Thick And Weight 43.478 Gm Per Metre Cost Of M.s. Angle, C.c. Blocks Shall Be Paid Separately, Supplying At Site Angle Iron Post And Strut Of Required Size Including Bottom To Be Split And Bent At Right Angle In Opposite Direction For 10 Cm Length And Drilling Holes Upto 10 Mm Dia. Etc. Complete. within the Jharkhand jurisdiction

10.

How can I find the submission closing date for this contract?

The official timeline and deadline details for Tender For Title1 , Title2 , Title3 , Title4 , Title5 , Title6 , Title7 , Title8 , Title9 , Title10 , Title11 , Title12 , Title13 , Title14 , Title15 , Title16 , Title17 , Title18 , Title19 , Title20 , Title21 , Title22 , Title23, Construction Of Boundary Wall At Aecs Secondary At Narwapahar Mines, Earth Work In Excavation By Mechanical Means Hydraulic Excavator Manual Means Over Areas Exceeding 30 Cm In Depth, 1.5 M In Width As Well As 10 Sqm On Plan Including Getting Out And Disposal Of Excavated Earth Lead Up To 50 M And Lift Up To 1.5 M, As Directed By Engineer In Charge. All Kind Of Soil, Filling Available Excavated Earth Excluding Rock In Trenches, Plinth, Sides Of Foundations Etc. In Layers Not Exceeding 20cm In Depth, Consolidating Each Deposited Layer By Ramming And Watering Lead Upto 50m And Lift Upto 1.50m., Clearing Jungle Including Uprooting Of Rank Vegetation, Grass, Brush Wood, Trees And Saplings Of Girth Up To 30 Cm Measured At A Height Of 1 M Above Ground Level And Removal Of Rubbish Upto A Distance Of 50m Outside The Periphery Of The Area Cleared., Providing And Laying In Position Cement Concrete Of Specified Grade Excluding The Cost Of Centering And Shuttering All Work Up To Plinth Levelshelves,chajja,lintel,band,plain Window Sills,stsiarcase And Spiral Stair Case Above Plinth Level Upto Floor Five Level Execluding The Cost Of Centering,shuttering,finishing And Reinforced With 1 Ratio 1.5 Ratio 3 1 Cement 1.5 Coarse Sand 3 Graded Stone Aggregate. 1 5 10 1 Cement 5 Coarse Sand Zone Iii Derived From Natural Sources 10 Graded Stone Aggregate 40 Mm Nominal Size Derived From Natural Sources, Providing And Laying Cement Concrete In Retaining Walls, Return Walls, Walls Any Thickness Including Attached Pilasters, Columns, Piers, Abutments, Pillars, Posts, Struts, Buttresses, String Or Lacing Courses, Parapets, Coping, Bed Blocks, Anchor Blocks, Plain Window Sills, Fillets, Sunken Floor Etc., Up To Floor Five Level, Excluding The Cost Of Centering, Shuttering And Finishing 1 2 4 1 Cement 2 Coarse Sand Zone Iii Derived From Natural Sources 4 Graded Stone Aggregate 20 Mm Nominal Size Derived From Natural Sources, Centering And Shuttering Including Strutting, Propping Etc And Removal Of Form Work For Foundations, Footings, Bases For Columns Foundations, Footings, Bases For Columns, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Foundations, Footings, Bases Of Columns, Etc. For Mass Concrete, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Lintels, Beams, Plinth Beams, Girders, Bressumers And Cantilevers, Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For Columns, Pillars, Piers, Abutments, Posts And Struts, Steel Reinforcement For R.c.c. Work Including Straightening, Cutting, Bending, Placing In Position And Binding All Complete Upto Plinth Level. Thermo Mechanically Treated Bars Of Grade Fe 500d Or More., Steel Reinforcement For R.c.c. Work Including Straightening, Cutting, Bending, Placing In Position And Binding All Complete Above Plinth Level. Thermo Mechanically Treated Bars Of Grade Fe 500d Or More., Providing And Laying In Position Machine Batched And Machine Mixed Design Mix M 25 Grade Cement Concrete For Reinforced Cement Concrete Work, Using Cement Content As Per Approved Design Mix, Including Pumping Of Concrete To Site Of Laying But Excluding The Cost Of Centering, Shuttering, Finishing And Reinforcement, Including Admixtures In Recommended Proportions As Per Is 9103 To Accelerate, Retard Setting Of Concrete, Improve Workability Without Impairing Strength And Durability As Per Direction Of Engineer In Charge. Note Cement Content Considered In This Item Is At The Rate 330 Kg Per Cum. Excess Or Less Cement Used As Per Design Mix Is Payable Or Recoverable Separately All Works Upto Plinth Level, Providing And Laying In Position Machine Batched And Machine Mixed Design Mix M 25 Grade Cement Concrete For Reinforced Cement Concrete Work, Using Cement Content As Per Approved Design Mix, Including Pumping Of Concrete To Site Of Laying But Excluding The Cost Of Centering, Shuttering, Finishing And Reinforcement, Including Admixtures In Recommended Proportions As Per Is 9103 To Accelerate, Retard Setting Of Concrete, Improve Workability Without Impairing Strength And Durability As Per Direction Of Engineer-in-charge. (note Cement Content Considered In This Item Is At The Rate 330 Kg Per Cum. Excess Or Less Cement Used As Per Design Mix Is Payable Or Recoverable Separately. All Works Above Plinth Level Upto Floor V Level., Add For Using Extra Cement In The Items Of Design Mix Over And Above The Specified Cement Content Therein., Brick Work With Common Burnt Clay F.p.s. Non Modular Bricks Of Class Designation 7.5 In Foundation And Plinth In Cement Mortar 1 6 1 Cement 6 Coarse Sand, Brick Work With Common Burnt Clay F.p.s. Non Modular Bricks Of Class Designation 7.5 In Superstructure Above Plinth Level Up To Floor V Level In All Shapes And Sizes In Cement Mortar 1 6 1 Cement 6 Coarse Sand, 12 Mm Cement Plaster Of Mix 1 6 1 Cement 6 Coarse Sand, 15 Mm Cement Plaster On Rough Side Of Single Or Half Brick Wall Of Mix 1 6 1 Cement 6 Coarse Sand, Finishing Walls With Premium Acrylic Smooth Exterior Paint With Silicone Additives Of Required Shade New Work Two Or More Coats Applied At The Rate 1.43 Ltr Per 10 Sqm Over And Including Priming Coat Of Exterior Primer Applied At The Rate 2.20 Kg Per10 Sqm, Applying Priming Coat With Ready Mixed Red Oxide Zinc Chromate Primer Of Approved Brand And Manufacture On Steel Galvanised Iron Steel Works, Painting With Synthetic Enamel Paint Of Approved Brand And Manufacture To Give An Even Shade Two Or More Coats On New Work, Providing And Fixing Concertina Coil Fencing With Punched Tape Concertina Coil 600 Mm Dia 10 Metre Openable Length Total Length 90 M, Having 50 Nos Rounds Per 6 Metre Length, Upto 3 M Height Of Wall With Existing Angle Iron Y Shaped Placed 2.4m Or 3.00 M Apart And With 9 Horizontal R.b.t. Reinforced Barbed Wire, Stud Tied With G.i. Staples And G.i. Clips To Retain Horizontal, Including Necessary Bolts Or G.i. Barbed Wire Tied To Angle Iron, All Complete As Per Direction Of Engineer In Charge, With Reinforced Barbed Tape R.b.t. Spring Core 2.5mm Thick Wire Of High Tensile Strength Of 165 Kg Per Sq.mm With Tape 0.52 Mm Thick And Weight 43.478 Gm Per Metre Cost Of M.s. Angle, C.c. Blocks Shall Be Paid Separately, Supplying At Site Angle Iron Post And Strut Of Required Size Including Bottom To Be Split And Bent At Right Angle In Opposite Direction For 10 Cm Length And Drilling Holes Upto 10 Mm Dia. Etc. Complete. are available inside the detailed notification files. Bidders planning to target this contract in Ghatshila should check the official portal schedule early to complete their online technical and financial submission well before the closing hours.

Get Expert Tender Bidding Support

Looking For Complete Tender Bidding Consultancy? Our Technical Experts Will Help You Prepare And Submit Your Tender Successfully.

Call Our Expert: +91 7069661818
Your Information Is 100% Secure & Confidential