tender for revolving chair (v5) (q2) , dressing mirror for cadets with wooden frame , teapoy with drawers for cadets , wooden cockpit platform for super dimona simulator , table with cpu hanger , chair revolving executive high back , bench three seater , sofa set 1 seater , chair visitor with handle , plastic bath stool , mattress foam 78x36x4 inch , desk for cadets , bench for cadets , book shelf for cadets , shoe rack for cadet, provision of misc items, dressing mirror for cadets with wooden frame overall size shall be 1050 mm long and 500 mm wide all wood shall be of teak wood the back of hat stand shall be provided 6 mm thick commercial plywcod a mirror of 990 mm high and 440 mm wide with 5mm thickness of make modiguardsaint gobain shall be provided with 25 mm x 30 mm teak wood frame all around the mirror two ms key plate of thickness 15 mm with key holes shall be provided in top two corners of hat stand all teak wood and teak ply surface shall be polished with french polish till attaining glossy finish rest all as per drg no gefur022025 a and sample held at g e khadakwasla, teapoy with drawers for cadets over all dimensions of teapoy with drawers shall 610mm high x 460mr1 wide x 300mm depth framework shall be made up of 25mm ms square pipe as per drawing two drawers each of width 150mm shall be provided drawer shall be run on telescopic channel of appropriate size handle shall be approved shape stainless steel of size 100mm long top of teapoy and all side upper sidebottombackfront of drawer shall be 18 mm thick bwr plywood pasted with laminated sneet of 09mm thick of approved shade on outer side and white on inner side make of laminated sheet centurymarinogreenlam all steel and iron surfaces shall be epoxy polyster powder coating black and thickness not less than 45 microns rest all as per drawing drg no gekfur042025 and specified and approved by user held in ge khadkwasla, wooden cockpit platform for super dimona simulator of size 3680 mm x 2450 mmx760 mm shall be made up of comm bwp plywood is 710 frame work shall be done with 50 mm thick 2 x 25mm bwp ply joint with adhesive and ss screw bwp comm ply for load bearing capacity of 1000 kg as per drawing attached and specification frame work shall be done with five horizontal side of size 2450 mm x 760 mm x 50 mm joint with four vertical side of size 3680 mm x 760 mm x 50 mm at the edge ie below the top ss strip of size 50mm x 3mm shall be provided in all vertical and horizontal frame top of platform shall be of size 3680 mm x 2450 mm of 25 mm thick bwp plywood is 710 two openings shall be provided on inner side of front compartment for easy access to switch point maintenance carpet of approved shade of thickness 34mm shall be provided on top of plate form and stair stair of size 840 mm x 900 mm x600 mm high of three steps as per drg made up of 25mm thick bwp plywood shall be provided 1 mm thick laminated sheet shall be pasted on all four wall side of plate form and stair rest all as per drg all items shall be required to be assemble at site, table with cpu hanger of size 1650 mm x 900 mm x 728 mm, chair revolving executive high back, bench three seater, sofa set 1 seater overall size width80cm depth 82cm height 85cm seating height 44 cm primary material pinewood finish colour burgundy upholstery material leatherette all as per manufacturer catalogue and specifications, chair visitor with handle abs back cover shall be provided all as per manufactured specifications as follo seat 4700 cm w x480 cm l back 465 cm w x605 cm h seat height 465 cm chair height 935 cm width depth of chair as measured from pedestal shall be widht 610 cm depth 645 cm seat assembly the seat assembly should be made up of 1201 cm thick hot pressed plywood upholstered with fabric upholstery covers and moulded polyurethane foam back assembly should made up of powder coated tubular frame the back should be upholsted using double layer spacer nesh fabric with high tenacity yarn armrest one peice armrests should be injectionmoulded from black copolymer polypropylene tubular frame the powder coated tubular frame should be cantilever type, plastic bath stool, mattress foam 78x36x4 inch, desk for cadets overall size shall be 1270x820x540mm steel frame work shall be of 32 x 32 mm ms square tube of wall thickness 16mm top shall be made of 18 mm thick bwr plywood pasted with laminated sheet of 09mm thick of approved shade on both side 06 mm thick wooden beading shall be provided all around the top sides of the desk shall be covered with 18 mm thick bwr plywood pasted with laminated sheet of 09mm thick of approved shade on both side front of the desk shall be covered with 18 mm thick bwr plywood pasted with laminated sheet of 09mm thick of approved shade on both side with a partition made of 32 x 32 mm ms square tube of 16 mm thickness a suitable elevation shall be provided on the front side of the desk all wooden surface shall be french polished and all steel and iron surfaces shall be epoxy polyester powder coated black and thickness not less than 45 microns shapesizespecifications and finish shall be as per sample drg nogekfur082024 as approved by user held in ge khadakwasla drg and specifications attached as appendix note final supply of all furniture items shall only be carried out after the sample approval of furniture by the consignee, bench for cadets overall size shall be 1220x410x870mm steel frame work shall be of 32 x 32 mm ms square tube of wall thickness 15mm seat size of seat shall be 1220x410x18 mm and back size of back shall be 1220x150x18 mm shall be made of 18 mm thick bwr plywood pasted with laminated sheet of 09mm thick of approved shade on both side 6 mm thick wooden beading shall be provided all around a storage space made of 15 x 15 mm ms square tubes of wall thickness 16mm shall be provided below the bench all wooden surface shall be french polished and all steel and iron surfaces shall be epoxy polyester powder coated black and thickness not less than 45 microns shapesizespecifications and finish shall be as per sample drg nogekfur092024 as approved by user held in ge khadakwasia drg and specifications attached as appendix note final supply of all furniture items shall only be carried out after the sample approval of furniture by the consignee, book shelf for cadets size 1980 mm h x 450 mm l x 550 d over all dimension of book shelf for cadets shall be 1980 mm high x 450 mm wide x 550 mm depth frame work shall be made up of 25 mm ms square pipe as por drg two drawers each of height 200 mm shall be provided at the bottom of book shelf drawer shalt be run on telescopic channal of appropriate size handle shall be of approved shapestainless steel of size 100 mm long all three sidef except front side of each compartment shall be covered upto 250 mm height with 10 mm thick bwr ply pasted with 09 mm approved mica on both side edges where seen in each compartment beading shall be made up of same mica to match with the body all sides frontbackbottom of each drawers shall be 18 mm thick bwr plywood pasted with laminated sheet of 09mm thick of approved shade on front side and pasted with 00 mm thick white shade on inner side edges where seen beading shall made up of same mica shall be pasted to match the body all steel and iron surfaces shall be epoxy polyester powder coating black and thickness not less than 50 microns rest all as per drg gekfur032023 approved by user and sample held at ge khadakwasla drawing and specifications attached as appendix, shoe rack for cadet mm h x 350 mm d size 850 mm l x 625 over all dimension of shoe rack cadet shall be 850 mm length x 625 mm high x 350 mm depth frame work shall be made up of 25 mm ms square pipe as per drg handle shall be of approved shape stainless steel of size 100 mm long all sides incl frontbackshelfsidetop of shoe rack shall be made up of 18 mm thick bwr ply pasted with 09 mm mica of approved shade on front side and inner side both door shall be hang on 75 mm ssl hinges two magnetic catcher shall be provided at the botton shelves edges where seen beading shall made up of same mica shall be pasted to match the body all steel and iron surfaces shall be epoxy polyester powder coating black and thickness not less than 50 microns rest all as per drg gekfur022023 approved by user and sample held at ge khadakwasla drawing and specifications attached as appendix

You can fill out the integrated inquiry form below on this detail page to share your company profile. Our consultancy desk will review your query regarding polyurethane foam,revolving chair,stainless steel,laminated sheet,furniture items,powder coating,wooden beading,seater chair,square pipe,bwp plywood,steel frame,square tube,bath stool,book shelf,shoe rack,teak wood,ms square,sofa set,bearing parameters and guide you on how to coordinate efficiently with the procurement team of Indian Army

Tender18 provides end-to-end professional bidding support and documentation advisory for Tender For Revolving Chair (v5) (q2) , Dressing Mirror For Cadets With Wooden Frame , Teapoy With Drawers For Cadets , Wooden Cockpit Platform For Super Dimona Simulator , Table With Cpu Hanger , Chair Revolving Executive High Back , Bench Three Seater , Sofa Set 1 Seater , Chair Visitor With Handle , Plastic Bath Stool , Mattress Foam 78x36x4 Inch , Desk For Cadets , Bench For Cadets , Book Shelf For Cadets , Shoe Rack For Cadet, Provision Of Misc Items, Dressing Mirror For Cadets With Wooden Frame Overall Size Shall Be 1050 Mm Long And 500 Mm Wide All Wood Shall Be Of Teak Wood The Back Of Hat Stand Shall Be Provided 6 Mm Thick Commercial Plywcod A Mirror Of 990 Mm High And 440 Mm Wide With 5mm Thickness Of Make Modiguardsaint Gobain Shall Be Provided With 25 Mm X 30 Mm Teak Wood Frame All Around The Mirror Two Ms Key Plate Of Thickness 15 Mm With Key Holes Shall Be Provided In Top Two Corners Of Hat Stand All Teak Wood And Teak Ply Surface Shall Be Polished With French Polish Till Attaining Glossy Finish Rest All As Per Drg No Gefur022025 A And Sample Held At G E Khadakwasla, Teapoy With Drawers For Cadets Over All Dimensions Of Teapoy With Drawers Shall 610mm High X 460mr1 Wide X 300mm Depth Framework Shall Be Made Up Of 25mm Ms Square Pipe As Per Drawing Two Drawers Each Of Width 150mm Shall Be Provided Drawer Shall Be Run On Telescopic Channel Of Appropriate Size Handle Shall Be Approved Shape Stainless Steel Of Size 100mm Long Top Of Teapoy And All Side Upper Sidebottombackfront Of Drawer Shall Be 18 Mm Thick Bwr Plywood Pasted With Laminated Sneet Of 09mm Thick Of Approved Shade On Outer Side And White On Inner Side Make Of Laminated Sheet Centurymarinogreenlam All Steel And Iron Surfaces Shall Be Epoxy Polyster Powder Coating Black And Thickness Not Less Than 45 Microns Rest All As Per Drawing Drg No Gekfur042025 And Specified And Approved By User Held In Ge Khadkwasla, Wooden Cockpit Platform For Super Dimona Simulator Of Size 3680 Mm X 2450 Mmx760 Mm Shall Be Made Up Of Comm Bwp Plywood Is 710 Frame Work Shall Be Done With 50 Mm Thick 2 X 25mm Bwp Ply Joint With Adhesive And Ss Screw Bwp Comm Ply For Load Bearing Capacity Of 1000 Kg As Per Drawing Attached And Specification Frame Work Shall Be Done With Five Horizontal Side Of Size 2450 Mm X 760 Mm X 50 Mm Joint With Four Vertical Side Of Size 3680 Mm X 760 Mm X 50 Mm At The Edge Ie Below The Top Ss Strip Of Size 50mm X 3mm Shall Be Provided In All Vertical And Horizontal Frame Top Of Platform Shall Be Of Size 3680 Mm X 2450 Mm Of 25 Mm Thick Bwp Plywood Is 710 Two Openings Shall Be Provided On Inner Side Of Front Compartment For Easy Access To Switch Point Maintenance Carpet Of Approved Shade Of Thickness 34mm Shall Be Provided On Top Of Plate Form And Stair Stair Of Size 840 Mm X 900 Mm X600 Mm High Of Three Steps As Per Drg Made Up Of 25mm Thick Bwp Plywood Shall Be Provided 1 Mm Thick Laminated Sheet Shall Be Pasted On All Four Wall Side Of Plate Form And Stair Rest All As Per Drg All Items Shall Be Required To Be Assemble At Site, Table With Cpu Hanger Of Size 1650 Mm X 900 Mm X 728 Mm, Chair Revolving Executive High Back, Bench Three Seater, Sofa Set 1 Seater Overall Size Width80cm Depth 82cm Height 85cm Seating Height 44 Cm Primary Material Pinewood Finish Colour Burgundy Upholstery Material Leatherette All As Per Manufacturer Catalogue And Specifications, Chair Visitor With Handle Abs Back Cover Shall Be Provided All As Per Manufactured Specifications As Follo Seat 4700 Cm W X480 Cm L Back 465 Cm W X605 Cm H Seat Height 465 Cm Chair Height 935 Cm Width Depth Of Chair As Measured From Pedestal Shall Be Widht 610 Cm Depth 645 Cm Seat Assembly The Seat Assembly Should Be Made Up Of 1201 Cm Thick Hot Pressed Plywood Upholstered With Fabric Upholstery Covers And Moulded Polyurethane Foam Back Assembly Should Made Up Of Powder Coated Tubular Frame The Back Should Be Upholsted Using Double Layer Spacer Nesh Fabric With High Tenacity Yarn Armrest One Peice Armrests Should Be Injectionmoulded From Black Copolymer Polypropylene Tubular Frame The Powder Coated Tubular Frame Should Be Cantilever Type, Plastic Bath Stool, Mattress Foam 78x36x4 Inch, Desk For Cadets Overall Size Shall Be 1270x820x540mm Steel Frame Work Shall Be Of 32 X 32 Mm Ms Square Tube Of Wall Thickness 16mm Top Shall Be Made Of 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side 06 Mm Thick Wooden Beading Shall Be Provided All Around The Top Sides Of The Desk Shall Be Covered With 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side Front Of The Desk Shall Be Covered With 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side With A Partition Made Of 32 X 32 Mm Ms Square Tube Of 16 Mm Thickness A Suitable Elevation Shall Be Provided On The Front Side Of The Desk All Wooden Surface Shall Be French Polished And All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coated Black And Thickness Not Less Than 45 Microns Shapesizespecifications And Finish Shall Be As Per Sample Drg Nogekfur082024 As Approved By User Held In Ge Khadakwasla Drg And Specifications Attached As Appendix Note Final Supply Of All Furniture Items Shall Only Be Carried Out After The Sample Approval Of Furniture By The Consignee, Bench For Cadets Overall Size Shall Be 1220x410x870mm Steel Frame Work Shall Be Of 32 X 32 Mm Ms Square Tube Of Wall Thickness 15mm Seat Size Of Seat Shall Be 1220x410x18 Mm And Back Size Of Back Shall Be 1220x150x18 Mm Shall Be Made Of 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side 6 Mm Thick Wooden Beading Shall Be Provided All Around A Storage Space Made Of 15 X 15 Mm Ms Square Tubes Of Wall Thickness 16mm Shall Be Provided Below The Bench All Wooden Surface Shall Be French Polished And All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coated Black And Thickness Not Less Than 45 Microns Shapesizespecifications And Finish Shall Be As Per Sample Drg Nogekfur092024 As Approved By User Held In Ge Khadakwasia Drg And Specifications Attached As Appendix Note Final Supply Of All Furniture Items Shall Only Be Carried Out After The Sample Approval Of Furniture By The Consignee, Book Shelf For Cadets Size 1980 Mm H X 450 Mm L X 550 D Over All Dimension Of Book Shelf For Cadets Shall Be 1980 Mm High X 450 Mm Wide X 550 Mm Depth Frame Work Shall Be Made Up Of 25 Mm Ms Square Pipe As Por Drg Two Drawers Each Of Height 200 Mm Shall Be Provided At The Bottom Of Book Shelf Drawer Shalt Be Run On Telescopic Channal Of Appropriate Size Handle Shall Be Of Approved Shapestainless Steel Of Size 100 Mm Long All Three Sidef Except Front Side Of Each Compartment Shall Be Covered Upto 250 Mm Height With 10 Mm Thick Bwr Ply Pasted With 09 Mm Approved Mica On Both Side Edges Where Seen In Each Compartment Beading Shall Be Made Up Of Same Mica To Match With The Body All Sides Frontbackbottom Of Each Drawers Shall Be 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Front Side And Pasted With 00 Mm Thick White Shade On Inner Side Edges Where Seen Beading Shall Made Up Of Same Mica Shall Be Pasted To Match The Body All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coating Black And Thickness Not Less Than 50 Microns Rest All As Per Drg Gekfur032023 Approved By User And Sample Held At Ge Khadakwasla Drawing And Specifications Attached As Appendix, Shoe Rack For Cadet Mm H X 350 Mm D Size 850 Mm L X 625 Over All Dimension Of Shoe Rack Cadet Shall Be 850 Mm Length X 625 Mm High X 350 Mm Depth Frame Work Shall Be Made Up Of 25 Mm Ms Square Pipe As Per Drg Handle Shall Be Of Approved Shape Stainless Steel Of Size 100 Mm Long All Sides Incl Frontbackshelfsidetop Of Shoe Rack Shall Be Made Up Of 18 Mm Thick Bwr Ply Pasted With 09 Mm Mica Of Approved Shade On Front Side And Inner Side Both Door Shall Be Hang On 75 Mm Ssl Hinges Two Magnetic Catcher Shall Be Provided At The Botton Shelves Edges Where Seen Beading Shall Made Up Of Same Mica Shall Be Pasted To Match The Body All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coating Black And Thickness Not Less Than 50 Microns Rest All As Per Drg Gekfur022023 Approved By User And Sample Held At Ge Khadakwasla Drawing And Specifications Attached As Appendix . Our senior analysts help you decode the complete project guidelines, manage accurate costing sheets, and complete error-free submissions on the official platform used by Indian Army.

Most online bids face rejection during the initial evaluation round due to avoidable errors like uploading blurred document scans, submitting expired DSCs, or missing critical experience papers required for Tender For Revolving Chair (v5) (q2) , Dressing Mirror For Cadets With Wooden Frame , Teapoy With Drawers For Cadets , Wooden Cockpit Platform For Super Dimona Simulator , Table With Cpu Hanger , Chair Revolving Executive High Back , Bench Three Seater , Sofa Set 1 Seater , Chair Visitor With Handle , Plastic Bath Stool , Mattress Foam 78x36x4 Inch , Desk For Cadets , Bench For Cadets , Book Shelf For Cadets , Shoe Rack For Cadet, Provision Of Misc Items, Dressing Mirror For Cadets With Wooden Frame Overall Size Shall Be 1050 Mm Long And 500 Mm Wide All Wood Shall Be Of Teak Wood The Back Of Hat Stand Shall Be Provided 6 Mm Thick Commercial Plywcod A Mirror Of 990 Mm High And 440 Mm Wide With 5mm Thickness Of Make Modiguardsaint Gobain Shall Be Provided With 25 Mm X 30 Mm Teak Wood Frame All Around The Mirror Two Ms Key Plate Of Thickness 15 Mm With Key Holes Shall Be Provided In Top Two Corners Of Hat Stand All Teak Wood And Teak Ply Surface Shall Be Polished With French Polish Till Attaining Glossy Finish Rest All As Per Drg No Gefur022025 A And Sample Held At G E Khadakwasla, Teapoy With Drawers For Cadets Over All Dimensions Of Teapoy With Drawers Shall 610mm High X 460mr1 Wide X 300mm Depth Framework Shall Be Made Up Of 25mm Ms Square Pipe As Per Drawing Two Drawers Each Of Width 150mm Shall Be Provided Drawer Shall Be Run On Telescopic Channel Of Appropriate Size Handle Shall Be Approved Shape Stainless Steel Of Size 100mm Long Top Of Teapoy And All Side Upper Sidebottombackfront Of Drawer Shall Be 18 Mm Thick Bwr Plywood Pasted With Laminated Sneet Of 09mm Thick Of Approved Shade On Outer Side And White On Inner Side Make Of Laminated Sheet Centurymarinogreenlam All Steel And Iron Surfaces Shall Be Epoxy Polyster Powder Coating Black And Thickness Not Less Than 45 Microns Rest All As Per Drawing Drg No Gekfur042025 And Specified And Approved By User Held In Ge Khadkwasla, Wooden Cockpit Platform For Super Dimona Simulator Of Size 3680 Mm X 2450 Mmx760 Mm Shall Be Made Up Of Comm Bwp Plywood Is 710 Frame Work Shall Be Done With 50 Mm Thick 2 X 25mm Bwp Ply Joint With Adhesive And Ss Screw Bwp Comm Ply For Load Bearing Capacity Of 1000 Kg As Per Drawing Attached And Specification Frame Work Shall Be Done With Five Horizontal Side Of Size 2450 Mm X 760 Mm X 50 Mm Joint With Four Vertical Side Of Size 3680 Mm X 760 Mm X 50 Mm At The Edge Ie Below The Top Ss Strip Of Size 50mm X 3mm Shall Be Provided In All Vertical And Horizontal Frame Top Of Platform Shall Be Of Size 3680 Mm X 2450 Mm Of 25 Mm Thick Bwp Plywood Is 710 Two Openings Shall Be Provided On Inner Side Of Front Compartment For Easy Access To Switch Point Maintenance Carpet Of Approved Shade Of Thickness 34mm Shall Be Provided On Top Of Plate Form And Stair Stair Of Size 840 Mm X 900 Mm X600 Mm High Of Three Steps As Per Drg Made Up Of 25mm Thick Bwp Plywood Shall Be Provided 1 Mm Thick Laminated Sheet Shall Be Pasted On All Four Wall Side Of Plate Form And Stair Rest All As Per Drg All Items Shall Be Required To Be Assemble At Site, Table With Cpu Hanger Of Size 1650 Mm X 900 Mm X 728 Mm, Chair Revolving Executive High Back, Bench Three Seater, Sofa Set 1 Seater Overall Size Width80cm Depth 82cm Height 85cm Seating Height 44 Cm Primary Material Pinewood Finish Colour Burgundy Upholstery Material Leatherette All As Per Manufacturer Catalogue And Specifications, Chair Visitor With Handle Abs Back Cover Shall Be Provided All As Per Manufactured Specifications As Follo Seat 4700 Cm W X480 Cm L Back 465 Cm W X605 Cm H Seat Height 465 Cm Chair Height 935 Cm Width Depth Of Chair As Measured From Pedestal Shall Be Widht 610 Cm Depth 645 Cm Seat Assembly The Seat Assembly Should Be Made Up Of 1201 Cm Thick Hot Pressed Plywood Upholstered With Fabric Upholstery Covers And Moulded Polyurethane Foam Back Assembly Should Made Up Of Powder Coated Tubular Frame The Back Should Be Upholsted Using Double Layer Spacer Nesh Fabric With High Tenacity Yarn Armrest One Peice Armrests Should Be Injectionmoulded From Black Copolymer Polypropylene Tubular Frame The Powder Coated Tubular Frame Should Be Cantilever Type, Plastic Bath Stool, Mattress Foam 78x36x4 Inch, Desk For Cadets Overall Size Shall Be 1270x820x540mm Steel Frame Work Shall Be Of 32 X 32 Mm Ms Square Tube Of Wall Thickness 16mm Top Shall Be Made Of 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side 06 Mm Thick Wooden Beading Shall Be Provided All Around The Top Sides Of The Desk Shall Be Covered With 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side Front Of The Desk Shall Be Covered With 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side With A Partition Made Of 32 X 32 Mm Ms Square Tube Of 16 Mm Thickness A Suitable Elevation Shall Be Provided On The Front Side Of The Desk All Wooden Surface Shall Be French Polished And All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coated Black And Thickness Not Less Than 45 Microns Shapesizespecifications And Finish Shall Be As Per Sample Drg Nogekfur082024 As Approved By User Held In Ge Khadakwasla Drg And Specifications Attached As Appendix Note Final Supply Of All Furniture Items Shall Only Be Carried Out After The Sample Approval Of Furniture By The Consignee, Bench For Cadets Overall Size Shall Be 1220x410x870mm Steel Frame Work Shall Be Of 32 X 32 Mm Ms Square Tube Of Wall Thickness 15mm Seat Size Of Seat Shall Be 1220x410x18 Mm And Back Size Of Back Shall Be 1220x150x18 Mm Shall Be Made Of 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side 6 Mm Thick Wooden Beading Shall Be Provided All Around A Storage Space Made Of 15 X 15 Mm Ms Square Tubes Of Wall Thickness 16mm Shall Be Provided Below The Bench All Wooden Surface Shall Be French Polished And All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coated Black And Thickness Not Less Than 45 Microns Shapesizespecifications And Finish Shall Be As Per Sample Drg Nogekfur092024 As Approved By User Held In Ge Khadakwasia Drg And Specifications Attached As Appendix Note Final Supply Of All Furniture Items Shall Only Be Carried Out After The Sample Approval Of Furniture By The Consignee, Book Shelf For Cadets Size 1980 Mm H X 450 Mm L X 550 D Over All Dimension Of Book Shelf For Cadets Shall Be 1980 Mm High X 450 Mm Wide X 550 Mm Depth Frame Work Shall Be Made Up Of 25 Mm Ms Square Pipe As Por Drg Two Drawers Each Of Height 200 Mm Shall Be Provided At The Bottom Of Book Shelf Drawer Shalt Be Run On Telescopic Channal Of Appropriate Size Handle Shall Be Of Approved Shapestainless Steel Of Size 100 Mm Long All Three Sidef Except Front Side Of Each Compartment Shall Be Covered Upto 250 Mm Height With 10 Mm Thick Bwr Ply Pasted With 09 Mm Approved Mica On Both Side Edges Where Seen In Each Compartment Beading Shall Be Made Up Of Same Mica To Match With The Body All Sides Frontbackbottom Of Each Drawers Shall Be 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Front Side And Pasted With 00 Mm Thick White Shade On Inner Side Edges Where Seen Beading Shall Made Up Of Same Mica Shall Be Pasted To Match The Body All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coating Black And Thickness Not Less Than 50 Microns Rest All As Per Drg Gekfur032023 Approved By User And Sample Held At Ge Khadakwasla Drawing And Specifications Attached As Appendix, Shoe Rack For Cadet Mm H X 350 Mm D Size 850 Mm L X 625 Over All Dimension Of Shoe Rack Cadet Shall Be 850 Mm Length X 625 Mm High X 350 Mm Depth Frame Work Shall Be Made Up Of 25 Mm Ms Square Pipe As Per Drg Handle Shall Be Of Approved Shape Stainless Steel Of Size 100 Mm Long All Sides Incl Frontbackshelfsidetop Of Shoe Rack Shall Be Made Up Of 18 Mm Thick Bwr Ply Pasted With 09 Mm Mica Of Approved Shade On Front Side And Inner Side Both Door Shall Be Hang On 75 Mm Ssl Hinges Two Magnetic Catcher Shall Be Provided At The Botton Shelves Edges Where Seen Beading Shall Made Up Of Same Mica Shall Be Pasted To Match The Body All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coating Black And Thickness Not Less Than 50 Microns Rest All As Per Drg Gekfur022023 Approved By User And Sample Held At Ge Khadakwasla Drawing And Specifications Attached As Appendix in Maharashtra.

Eligibility for outstation bidders depends entirely on the terms set inside the document for Tender For Revolving Chair (v5) (q2) , Dressing Mirror For Cadets With Wooden Frame , Teapoy With Drawers For Cadets , Wooden Cockpit Platform For Super Dimona Simulator , Table With Cpu Hanger , Chair Revolving Executive High Back , Bench Three Seater , Sofa Set 1 Seater , Chair Visitor With Handle , Plastic Bath Stool , Mattress Foam 78x36x4 Inch , Desk For Cadets , Bench For Cadets , Book Shelf For Cadets , Shoe Rack For Cadet, Provision Of Misc Items, Dressing Mirror For Cadets With Wooden Frame Overall Size Shall Be 1050 Mm Long And 500 Mm Wide All Wood Shall Be Of Teak Wood The Back Of Hat Stand Shall Be Provided 6 Mm Thick Commercial Plywcod A Mirror Of 990 Mm High And 440 Mm Wide With 5mm Thickness Of Make Modiguardsaint Gobain Shall Be Provided With 25 Mm X 30 Mm Teak Wood Frame All Around The Mirror Two Ms Key Plate Of Thickness 15 Mm With Key Holes Shall Be Provided In Top Two Corners Of Hat Stand All Teak Wood And Teak Ply Surface Shall Be Polished With French Polish Till Attaining Glossy Finish Rest All As Per Drg No Gefur022025 A And Sample Held At G E Khadakwasla, Teapoy With Drawers For Cadets Over All Dimensions Of Teapoy With Drawers Shall 610mm High X 460mr1 Wide X 300mm Depth Framework Shall Be Made Up Of 25mm Ms Square Pipe As Per Drawing Two Drawers Each Of Width 150mm Shall Be Provided Drawer Shall Be Run On Telescopic Channel Of Appropriate Size Handle Shall Be Approved Shape Stainless Steel Of Size 100mm Long Top Of Teapoy And All Side Upper Sidebottombackfront Of Drawer Shall Be 18 Mm Thick Bwr Plywood Pasted With Laminated Sneet Of 09mm Thick Of Approved Shade On Outer Side And White On Inner Side Make Of Laminated Sheet Centurymarinogreenlam All Steel And Iron Surfaces Shall Be Epoxy Polyster Powder Coating Black And Thickness Not Less Than 45 Microns Rest All As Per Drawing Drg No Gekfur042025 And Specified And Approved By User Held In Ge Khadkwasla, Wooden Cockpit Platform For Super Dimona Simulator Of Size 3680 Mm X 2450 Mmx760 Mm Shall Be Made Up Of Comm Bwp Plywood Is 710 Frame Work Shall Be Done With 50 Mm Thick 2 X 25mm Bwp Ply Joint With Adhesive And Ss Screw Bwp Comm Ply For Load Bearing Capacity Of 1000 Kg As Per Drawing Attached And Specification Frame Work Shall Be Done With Five Horizontal Side Of Size 2450 Mm X 760 Mm X 50 Mm Joint With Four Vertical Side Of Size 3680 Mm X 760 Mm X 50 Mm At The Edge Ie Below The Top Ss Strip Of Size 50mm X 3mm Shall Be Provided In All Vertical And Horizontal Frame Top Of Platform Shall Be Of Size 3680 Mm X 2450 Mm Of 25 Mm Thick Bwp Plywood Is 710 Two Openings Shall Be Provided On Inner Side Of Front Compartment For Easy Access To Switch Point Maintenance Carpet Of Approved Shade Of Thickness 34mm Shall Be Provided On Top Of Plate Form And Stair Stair Of Size 840 Mm X 900 Mm X600 Mm High Of Three Steps As Per Drg Made Up Of 25mm Thick Bwp Plywood Shall Be Provided 1 Mm Thick Laminated Sheet Shall Be Pasted On All Four Wall Side Of Plate Form And Stair Rest All As Per Drg All Items Shall Be Required To Be Assemble At Site, Table With Cpu Hanger Of Size 1650 Mm X 900 Mm X 728 Mm, Chair Revolving Executive High Back, Bench Three Seater, Sofa Set 1 Seater Overall Size Width80cm Depth 82cm Height 85cm Seating Height 44 Cm Primary Material Pinewood Finish Colour Burgundy Upholstery Material Leatherette All As Per Manufacturer Catalogue And Specifications, Chair Visitor With Handle Abs Back Cover Shall Be Provided All As Per Manufactured Specifications As Follo Seat 4700 Cm W X480 Cm L Back 465 Cm W X605 Cm H Seat Height 465 Cm Chair Height 935 Cm Width Depth Of Chair As Measured From Pedestal Shall Be Widht 610 Cm Depth 645 Cm Seat Assembly The Seat Assembly Should Be Made Up Of 1201 Cm Thick Hot Pressed Plywood Upholstered With Fabric Upholstery Covers And Moulded Polyurethane Foam Back Assembly Should Made Up Of Powder Coated Tubular Frame The Back Should Be Upholsted Using Double Layer Spacer Nesh Fabric With High Tenacity Yarn Armrest One Peice Armrests Should Be Injectionmoulded From Black Copolymer Polypropylene Tubular Frame The Powder Coated Tubular Frame Should Be Cantilever Type, Plastic Bath Stool, Mattress Foam 78x36x4 Inch, Desk For Cadets Overall Size Shall Be 1270x820x540mm Steel Frame Work Shall Be Of 32 X 32 Mm Ms Square Tube Of Wall Thickness 16mm Top Shall Be Made Of 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side 06 Mm Thick Wooden Beading Shall Be Provided All Around The Top Sides Of The Desk Shall Be Covered With 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side Front Of The Desk Shall Be Covered With 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side With A Partition Made Of 32 X 32 Mm Ms Square Tube Of 16 Mm Thickness A Suitable Elevation Shall Be Provided On The Front Side Of The Desk All Wooden Surface Shall Be French Polished And All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coated Black And Thickness Not Less Than 45 Microns Shapesizespecifications And Finish Shall Be As Per Sample Drg Nogekfur082024 As Approved By User Held In Ge Khadakwasla Drg And Specifications Attached As Appendix Note Final Supply Of All Furniture Items Shall Only Be Carried Out After The Sample Approval Of Furniture By The Consignee, Bench For Cadets Overall Size Shall Be 1220x410x870mm Steel Frame Work Shall Be Of 32 X 32 Mm Ms Square Tube Of Wall Thickness 15mm Seat Size Of Seat Shall Be 1220x410x18 Mm And Back Size Of Back Shall Be 1220x150x18 Mm Shall Be Made Of 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side 6 Mm Thick Wooden Beading Shall Be Provided All Around A Storage Space Made Of 15 X 15 Mm Ms Square Tubes Of Wall Thickness 16mm Shall Be Provided Below The Bench All Wooden Surface Shall Be French Polished And All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coated Black And Thickness Not Less Than 45 Microns Shapesizespecifications And Finish Shall Be As Per Sample Drg Nogekfur092024 As Approved By User Held In Ge Khadakwasia Drg And Specifications Attached As Appendix Note Final Supply Of All Furniture Items Shall Only Be Carried Out After The Sample Approval Of Furniture By The Consignee, Book Shelf For Cadets Size 1980 Mm H X 450 Mm L X 550 D Over All Dimension Of Book Shelf For Cadets Shall Be 1980 Mm High X 450 Mm Wide X 550 Mm Depth Frame Work Shall Be Made Up Of 25 Mm Ms Square Pipe As Por Drg Two Drawers Each Of Height 200 Mm Shall Be Provided At The Bottom Of Book Shelf Drawer Shalt Be Run On Telescopic Channal Of Appropriate Size Handle Shall Be Of Approved Shapestainless Steel Of Size 100 Mm Long All Three Sidef Except Front Side Of Each Compartment Shall Be Covered Upto 250 Mm Height With 10 Mm Thick Bwr Ply Pasted With 09 Mm Approved Mica On Both Side Edges Where Seen In Each Compartment Beading Shall Be Made Up Of Same Mica To Match With The Body All Sides Frontbackbottom Of Each Drawers Shall Be 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Front Side And Pasted With 00 Mm Thick White Shade On Inner Side Edges Where Seen Beading Shall Made Up Of Same Mica Shall Be Pasted To Match The Body All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coating Black And Thickness Not Less Than 50 Microns Rest All As Per Drg Gekfur032023 Approved By User And Sample Held At Ge Khadakwasla Drawing And Specifications Attached As Appendix, Shoe Rack For Cadet Mm H X 350 Mm D Size 850 Mm L X 625 Over All Dimension Of Shoe Rack Cadet Shall Be 850 Mm Length X 625 Mm High X 350 Mm Depth Frame Work Shall Be Made Up Of 25 Mm Ms Square Pipe As Per Drg Handle Shall Be Of Approved Shape Stainless Steel Of Size 100 Mm Long All Sides Incl Frontbackshelfsidetop Of Shoe Rack Shall Be Made Up Of 18 Mm Thick Bwr Ply Pasted With 09 Mm Mica Of Approved Shade On Front Side And Inner Side Both Door Shall Be Hang On 75 Mm Ssl Hinges Two Magnetic Catcher Shall Be Provided At The Botton Shelves Edges Where Seen Beading Shall Made Up Of Same Mica Shall Be Pasted To Match The Body All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coating Black And Thickness Not Less Than 50 Microns Rest All As Per Drg Gekfur022023 Approved By User And Sample Held At Ge Khadakwasla Drawing And Specifications Attached As Appendix. While many public sector projects allow national competitive bidding, certain localized works require local offices or specific registration metrics in Pune.

If this procurement is routed through the central marketplace, an active GeM Seller ID is mandatory to supply polyurethane foam,revolving chair,stainless steel,laminated sheet,furniture items,powder coating,wooden beading,seater chair,square pipe,bwp plywood,steel frame,square tube,bath stool,book shelf,shoe rack,teak wood,ms square,sofa set,bearing items. Tender18 offers complete assistance for brand cataloging, profile creation, and vendor assessment required officially by Indian Army

To register an eligible bid for these polyurethane foam,revolving chair,stainless steel,laminated sheet,furniture items,powder coating,wooden beading,seater chair,square pipe,bwp plywood,steel frame,square tube,bath stool,book shelf,shoe rack,teak wood,ms square,sofa set,bearing contracts, companies must prepare their core compliance documents. Vendors operating across Maharashtra must ensure they possess a valid GST registration, permanent account number (PAN), and active Class-3 Digital Signature Certificates.

This public procurement cycle is specifically looking for qualified vendors and suppliers who can provide high-quality polyurethane foam,revolving chair,stainless steel,laminated sheet,furniture items,powder coating,wooden beading,seater chair,square pipe,bwp plywood,steel frame,square tube,bath stool,book shelf,shoe rack,teak wood,ms square,sofa set,bearing solutions. The operational execution, delivery, and deployment of these materials must be managed locally within the Pune region.

The estimated project cost and budget thresholds can be reviewed directly inside the tender document. Bidders can analyze these qualification files to check if their firm meets the financial capability criteria specified for Tender For Revolving Chair (v5) (q2) , Dressing Mirror For Cadets With Wooden Frame , Teapoy With Drawers For Cadets , Wooden Cockpit Platform For Super Dimona Simulator , Table With Cpu Hanger , Chair Revolving Executive High Back , Bench Three Seater , Sofa Set 1 Seater , Chair Visitor With Handle , Plastic Bath Stool , Mattress Foam 78x36x4 Inch , Desk For Cadets , Bench For Cadets , Book Shelf For Cadets , Shoe Rack For Cadet, Provision Of Misc Items, Dressing Mirror For Cadets With Wooden Frame Overall Size Shall Be 1050 Mm Long And 500 Mm Wide All Wood Shall Be Of Teak Wood The Back Of Hat Stand Shall Be Provided 6 Mm Thick Commercial Plywcod A Mirror Of 990 Mm High And 440 Mm Wide With 5mm Thickness Of Make Modiguardsaint Gobain Shall Be Provided With 25 Mm X 30 Mm Teak Wood Frame All Around The Mirror Two Ms Key Plate Of Thickness 15 Mm With Key Holes Shall Be Provided In Top Two Corners Of Hat Stand All Teak Wood And Teak Ply Surface Shall Be Polished With French Polish Till Attaining Glossy Finish Rest All As Per Drg No Gefur022025 A And Sample Held At G E Khadakwasla, Teapoy With Drawers For Cadets Over All Dimensions Of Teapoy With Drawers Shall 610mm High X 460mr1 Wide X 300mm Depth Framework Shall Be Made Up Of 25mm Ms Square Pipe As Per Drawing Two Drawers Each Of Width 150mm Shall Be Provided Drawer Shall Be Run On Telescopic Channel Of Appropriate Size Handle Shall Be Approved Shape Stainless Steel Of Size 100mm Long Top Of Teapoy And All Side Upper Sidebottombackfront Of Drawer Shall Be 18 Mm Thick Bwr Plywood Pasted With Laminated Sneet Of 09mm Thick Of Approved Shade On Outer Side And White On Inner Side Make Of Laminated Sheet Centurymarinogreenlam All Steel And Iron Surfaces Shall Be Epoxy Polyster Powder Coating Black And Thickness Not Less Than 45 Microns Rest All As Per Drawing Drg No Gekfur042025 And Specified And Approved By User Held In Ge Khadkwasla, Wooden Cockpit Platform For Super Dimona Simulator Of Size 3680 Mm X 2450 Mmx760 Mm Shall Be Made Up Of Comm Bwp Plywood Is 710 Frame Work Shall Be Done With 50 Mm Thick 2 X 25mm Bwp Ply Joint With Adhesive And Ss Screw Bwp Comm Ply For Load Bearing Capacity Of 1000 Kg As Per Drawing Attached And Specification Frame Work Shall Be Done With Five Horizontal Side Of Size 2450 Mm X 760 Mm X 50 Mm Joint With Four Vertical Side Of Size 3680 Mm X 760 Mm X 50 Mm At The Edge Ie Below The Top Ss Strip Of Size 50mm X 3mm Shall Be Provided In All Vertical And Horizontal Frame Top Of Platform Shall Be Of Size 3680 Mm X 2450 Mm Of 25 Mm Thick Bwp Plywood Is 710 Two Openings Shall Be Provided On Inner Side Of Front Compartment For Easy Access To Switch Point Maintenance Carpet Of Approved Shade Of Thickness 34mm Shall Be Provided On Top Of Plate Form And Stair Stair Of Size 840 Mm X 900 Mm X600 Mm High Of Three Steps As Per Drg Made Up Of 25mm Thick Bwp Plywood Shall Be Provided 1 Mm Thick Laminated Sheet Shall Be Pasted On All Four Wall Side Of Plate Form And Stair Rest All As Per Drg All Items Shall Be Required To Be Assemble At Site, Table With Cpu Hanger Of Size 1650 Mm X 900 Mm X 728 Mm, Chair Revolving Executive High Back, Bench Three Seater, Sofa Set 1 Seater Overall Size Width80cm Depth 82cm Height 85cm Seating Height 44 Cm Primary Material Pinewood Finish Colour Burgundy Upholstery Material Leatherette All As Per Manufacturer Catalogue And Specifications, Chair Visitor With Handle Abs Back Cover Shall Be Provided All As Per Manufactured Specifications As Follo Seat 4700 Cm W X480 Cm L Back 465 Cm W X605 Cm H Seat Height 465 Cm Chair Height 935 Cm Width Depth Of Chair As Measured From Pedestal Shall Be Widht 610 Cm Depth 645 Cm Seat Assembly The Seat Assembly Should Be Made Up Of 1201 Cm Thick Hot Pressed Plywood Upholstered With Fabric Upholstery Covers And Moulded Polyurethane Foam Back Assembly Should Made Up Of Powder Coated Tubular Frame The Back Should Be Upholsted Using Double Layer Spacer Nesh Fabric With High Tenacity Yarn Armrest One Peice Armrests Should Be Injectionmoulded From Black Copolymer Polypropylene Tubular Frame The Powder Coated Tubular Frame Should Be Cantilever Type, Plastic Bath Stool, Mattress Foam 78x36x4 Inch, Desk For Cadets Overall Size Shall Be 1270x820x540mm Steel Frame Work Shall Be Of 32 X 32 Mm Ms Square Tube Of Wall Thickness 16mm Top Shall Be Made Of 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side 06 Mm Thick Wooden Beading Shall Be Provided All Around The Top Sides Of The Desk Shall Be Covered With 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side Front Of The Desk Shall Be Covered With 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side With A Partition Made Of 32 X 32 Mm Ms Square Tube Of 16 Mm Thickness A Suitable Elevation Shall Be Provided On The Front Side Of The Desk All Wooden Surface Shall Be French Polished And All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coated Black And Thickness Not Less Than 45 Microns Shapesizespecifications And Finish Shall Be As Per Sample Drg Nogekfur082024 As Approved By User Held In Ge Khadakwasla Drg And Specifications Attached As Appendix Note Final Supply Of All Furniture Items Shall Only Be Carried Out After The Sample Approval Of Furniture By The Consignee, Bench For Cadets Overall Size Shall Be 1220x410x870mm Steel Frame Work Shall Be Of 32 X 32 Mm Ms Square Tube Of Wall Thickness 15mm Seat Size Of Seat Shall Be 1220x410x18 Mm And Back Size Of Back Shall Be 1220x150x18 Mm Shall Be Made Of 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side 6 Mm Thick Wooden Beading Shall Be Provided All Around A Storage Space Made Of 15 X 15 Mm Ms Square Tubes Of Wall Thickness 16mm Shall Be Provided Below The Bench All Wooden Surface Shall Be French Polished And All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coated Black And Thickness Not Less Than 45 Microns Shapesizespecifications And Finish Shall Be As Per Sample Drg Nogekfur092024 As Approved By User Held In Ge Khadakwasia Drg And Specifications Attached As Appendix Note Final Supply Of All Furniture Items Shall Only Be Carried Out After The Sample Approval Of Furniture By The Consignee, Book Shelf For Cadets Size 1980 Mm H X 450 Mm L X 550 D Over All Dimension Of Book Shelf For Cadets Shall Be 1980 Mm High X 450 Mm Wide X 550 Mm Depth Frame Work Shall Be Made Up Of 25 Mm Ms Square Pipe As Por Drg Two Drawers Each Of Height 200 Mm Shall Be Provided At The Bottom Of Book Shelf Drawer Shalt Be Run On Telescopic Channal Of Appropriate Size Handle Shall Be Of Approved Shapestainless Steel Of Size 100 Mm Long All Three Sidef Except Front Side Of Each Compartment Shall Be Covered Upto 250 Mm Height With 10 Mm Thick Bwr Ply Pasted With 09 Mm Approved Mica On Both Side Edges Where Seen In Each Compartment Beading Shall Be Made Up Of Same Mica To Match With The Body All Sides Frontbackbottom Of Each Drawers Shall Be 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Front Side And Pasted With 00 Mm Thick White Shade On Inner Side Edges Where Seen Beading Shall Made Up Of Same Mica Shall Be Pasted To Match The Body All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coating Black And Thickness Not Less Than 50 Microns Rest All As Per Drg Gekfur032023 Approved By User And Sample Held At Ge Khadakwasla Drawing And Specifications Attached As Appendix, Shoe Rack For Cadet Mm H X 350 Mm D Size 850 Mm L X 625 Over All Dimension Of Shoe Rack Cadet Shall Be 850 Mm Length X 625 Mm High X 350 Mm Depth Frame Work Shall Be Made Up Of 25 Mm Ms Square Pipe As Per Drg Handle Shall Be Of Approved Shape Stainless Steel Of Size 100 Mm Long All Sides Incl Frontbackshelfsidetop Of Shoe Rack Shall Be Made Up Of 18 Mm Thick Bwr Ply Pasted With 09 Mm Mica Of Approved Shade On Front Side And Inner Side Both Door Shall Be Hang On 75 Mm Ssl Hinges Two Magnetic Catcher Shall Be Provided At The Botton Shelves Edges Where Seen Beading Shall Made Up Of Same Mica Shall Be Pasted To Match The Body All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coating Black And Thickness Not Less Than 50 Microns Rest All As Per Drg Gekfur022023 Approved By User And Sample Held At Ge Khadakwasla Drawing And Specifications Attached As Appendix by Indian Army

You can download the commercial Bill of Quantities (BOQ) spreadsheet directly using the secure link provided on this page. The BOQ file contains the item descriptions and rate filling forms officially validated for Tender For Revolving Chair (v5) (q2) , Dressing Mirror For Cadets With Wooden Frame , Teapoy With Drawers For Cadets , Wooden Cockpit Platform For Super Dimona Simulator , Table With Cpu Hanger , Chair Revolving Executive High Back , Bench Three Seater , Sofa Set 1 Seater , Chair Visitor With Handle , Plastic Bath Stool , Mattress Foam 78x36x4 Inch , Desk For Cadets , Bench For Cadets , Book Shelf For Cadets , Shoe Rack For Cadet, Provision Of Misc Items, Dressing Mirror For Cadets With Wooden Frame Overall Size Shall Be 1050 Mm Long And 500 Mm Wide All Wood Shall Be Of Teak Wood The Back Of Hat Stand Shall Be Provided 6 Mm Thick Commercial Plywcod A Mirror Of 990 Mm High And 440 Mm Wide With 5mm Thickness Of Make Modiguardsaint Gobain Shall Be Provided With 25 Mm X 30 Mm Teak Wood Frame All Around The Mirror Two Ms Key Plate Of Thickness 15 Mm With Key Holes Shall Be Provided In Top Two Corners Of Hat Stand All Teak Wood And Teak Ply Surface Shall Be Polished With French Polish Till Attaining Glossy Finish Rest All As Per Drg No Gefur022025 A And Sample Held At G E Khadakwasla, Teapoy With Drawers For Cadets Over All Dimensions Of Teapoy With Drawers Shall 610mm High X 460mr1 Wide X 300mm Depth Framework Shall Be Made Up Of 25mm Ms Square Pipe As Per Drawing Two Drawers Each Of Width 150mm Shall Be Provided Drawer Shall Be Run On Telescopic Channel Of Appropriate Size Handle Shall Be Approved Shape Stainless Steel Of Size 100mm Long Top Of Teapoy And All Side Upper Sidebottombackfront Of Drawer Shall Be 18 Mm Thick Bwr Plywood Pasted With Laminated Sneet Of 09mm Thick Of Approved Shade On Outer Side And White On Inner Side Make Of Laminated Sheet Centurymarinogreenlam All Steel And Iron Surfaces Shall Be Epoxy Polyster Powder Coating Black And Thickness Not Less Than 45 Microns Rest All As Per Drawing Drg No Gekfur042025 And Specified And Approved By User Held In Ge Khadkwasla, Wooden Cockpit Platform For Super Dimona Simulator Of Size 3680 Mm X 2450 Mmx760 Mm Shall Be Made Up Of Comm Bwp Plywood Is 710 Frame Work Shall Be Done With 50 Mm Thick 2 X 25mm Bwp Ply Joint With Adhesive And Ss Screw Bwp Comm Ply For Load Bearing Capacity Of 1000 Kg As Per Drawing Attached And Specification Frame Work Shall Be Done With Five Horizontal Side Of Size 2450 Mm X 760 Mm X 50 Mm Joint With Four Vertical Side Of Size 3680 Mm X 760 Mm X 50 Mm At The Edge Ie Below The Top Ss Strip Of Size 50mm X 3mm Shall Be Provided In All Vertical And Horizontal Frame Top Of Platform Shall Be Of Size 3680 Mm X 2450 Mm Of 25 Mm Thick Bwp Plywood Is 710 Two Openings Shall Be Provided On Inner Side Of Front Compartment For Easy Access To Switch Point Maintenance Carpet Of Approved Shade Of Thickness 34mm Shall Be Provided On Top Of Plate Form And Stair Stair Of Size 840 Mm X 900 Mm X600 Mm High Of Three Steps As Per Drg Made Up Of 25mm Thick Bwp Plywood Shall Be Provided 1 Mm Thick Laminated Sheet Shall Be Pasted On All Four Wall Side Of Plate Form And Stair Rest All As Per Drg All Items Shall Be Required To Be Assemble At Site, Table With Cpu Hanger Of Size 1650 Mm X 900 Mm X 728 Mm, Chair Revolving Executive High Back, Bench Three Seater, Sofa Set 1 Seater Overall Size Width80cm Depth 82cm Height 85cm Seating Height 44 Cm Primary Material Pinewood Finish Colour Burgundy Upholstery Material Leatherette All As Per Manufacturer Catalogue And Specifications, Chair Visitor With Handle Abs Back Cover Shall Be Provided All As Per Manufactured Specifications As Follo Seat 4700 Cm W X480 Cm L Back 465 Cm W X605 Cm H Seat Height 465 Cm Chair Height 935 Cm Width Depth Of Chair As Measured From Pedestal Shall Be Widht 610 Cm Depth 645 Cm Seat Assembly The Seat Assembly Should Be Made Up Of 1201 Cm Thick Hot Pressed Plywood Upholstered With Fabric Upholstery Covers And Moulded Polyurethane Foam Back Assembly Should Made Up Of Powder Coated Tubular Frame The Back Should Be Upholsted Using Double Layer Spacer Nesh Fabric With High Tenacity Yarn Armrest One Peice Armrests Should Be Injectionmoulded From Black Copolymer Polypropylene Tubular Frame The Powder Coated Tubular Frame Should Be Cantilever Type, Plastic Bath Stool, Mattress Foam 78x36x4 Inch, Desk For Cadets Overall Size Shall Be 1270x820x540mm Steel Frame Work Shall Be Of 32 X 32 Mm Ms Square Tube Of Wall Thickness 16mm Top Shall Be Made Of 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side 06 Mm Thick Wooden Beading Shall Be Provided All Around The Top Sides Of The Desk Shall Be Covered With 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side Front Of The Desk Shall Be Covered With 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side With A Partition Made Of 32 X 32 Mm Ms Square Tube Of 16 Mm Thickness A Suitable Elevation Shall Be Provided On The Front Side Of The Desk All Wooden Surface Shall Be French Polished And All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coated Black And Thickness Not Less Than 45 Microns Shapesizespecifications And Finish Shall Be As Per Sample Drg Nogekfur082024 As Approved By User Held In Ge Khadakwasla Drg And Specifications Attached As Appendix Note Final Supply Of All Furniture Items Shall Only Be Carried Out After The Sample Approval Of Furniture By The Consignee, Bench For Cadets Overall Size Shall Be 1220x410x870mm Steel Frame Work Shall Be Of 32 X 32 Mm Ms Square Tube Of Wall Thickness 15mm Seat Size Of Seat Shall Be 1220x410x18 Mm And Back Size Of Back Shall Be 1220x150x18 Mm Shall Be Made Of 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side 6 Mm Thick Wooden Beading Shall Be Provided All Around A Storage Space Made Of 15 X 15 Mm Ms Square Tubes Of Wall Thickness 16mm Shall Be Provided Below The Bench All Wooden Surface Shall Be French Polished And All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coated Black And Thickness Not Less Than 45 Microns Shapesizespecifications And Finish Shall Be As Per Sample Drg Nogekfur092024 As Approved By User Held In Ge Khadakwasia Drg And Specifications Attached As Appendix Note Final Supply Of All Furniture Items Shall Only Be Carried Out After The Sample Approval Of Furniture By The Consignee, Book Shelf For Cadets Size 1980 Mm H X 450 Mm L X 550 D Over All Dimension Of Book Shelf For Cadets Shall Be 1980 Mm High X 450 Mm Wide X 550 Mm Depth Frame Work Shall Be Made Up Of 25 Mm Ms Square Pipe As Por Drg Two Drawers Each Of Height 200 Mm Shall Be Provided At The Bottom Of Book Shelf Drawer Shalt Be Run On Telescopic Channal Of Appropriate Size Handle Shall Be Of Approved Shapestainless Steel Of Size 100 Mm Long All Three Sidef Except Front Side Of Each Compartment Shall Be Covered Upto 250 Mm Height With 10 Mm Thick Bwr Ply Pasted With 09 Mm Approved Mica On Both Side Edges Where Seen In Each Compartment Beading Shall Be Made Up Of Same Mica To Match With The Body All Sides Frontbackbottom Of Each Drawers Shall Be 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Front Side And Pasted With 00 Mm Thick White Shade On Inner Side Edges Where Seen Beading Shall Made Up Of Same Mica Shall Be Pasted To Match The Body All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coating Black And Thickness Not Less Than 50 Microns Rest All As Per Drg Gekfur032023 Approved By User And Sample Held At Ge Khadakwasla Drawing And Specifications Attached As Appendix, Shoe Rack For Cadet Mm H X 350 Mm D Size 850 Mm L X 625 Over All Dimension Of Shoe Rack Cadet Shall Be 850 Mm Length X 625 Mm High X 350 Mm Depth Frame Work Shall Be Made Up Of 25 Mm Ms Square Pipe As Per Drg Handle Shall Be Of Approved Shape Stainless Steel Of Size 100 Mm Long All Sides Incl Frontbackshelfsidetop Of Shoe Rack Shall Be Made Up Of 18 Mm Thick Bwr Ply Pasted With 09 Mm Mica Of Approved Shade On Front Side And Inner Side Both Door Shall Be Hang On 75 Mm Ssl Hinges Two Magnetic Catcher Shall Be Provided At The Botton Shelves Edges Where Seen Beading Shall Made Up Of Same Mica Shall Be Pasted To Match The Body All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coating Black And Thickness Not Less Than 50 Microns Rest All As Per Drg Gekfur022023 Approved By User And Sample Held At Ge Khadakwasla Drawing And Specifications Attached As Appendix within the Maharashtra jurisdiction

The official timeline and deadline details for Tender For Revolving Chair (v5) (q2) , Dressing Mirror For Cadets With Wooden Frame , Teapoy With Drawers For Cadets , Wooden Cockpit Platform For Super Dimona Simulator , Table With Cpu Hanger , Chair Revolving Executive High Back , Bench Three Seater , Sofa Set 1 Seater , Chair Visitor With Handle , Plastic Bath Stool , Mattress Foam 78x36x4 Inch , Desk For Cadets , Bench For Cadets , Book Shelf For Cadets , Shoe Rack For Cadet, Provision Of Misc Items, Dressing Mirror For Cadets With Wooden Frame Overall Size Shall Be 1050 Mm Long And 500 Mm Wide All Wood Shall Be Of Teak Wood The Back Of Hat Stand Shall Be Provided 6 Mm Thick Commercial Plywcod A Mirror Of 990 Mm High And 440 Mm Wide With 5mm Thickness Of Make Modiguardsaint Gobain Shall Be Provided With 25 Mm X 30 Mm Teak Wood Frame All Around The Mirror Two Ms Key Plate Of Thickness 15 Mm With Key Holes Shall Be Provided In Top Two Corners Of Hat Stand All Teak Wood And Teak Ply Surface Shall Be Polished With French Polish Till Attaining Glossy Finish Rest All As Per Drg No Gefur022025 A And Sample Held At G E Khadakwasla, Teapoy With Drawers For Cadets Over All Dimensions Of Teapoy With Drawers Shall 610mm High X 460mr1 Wide X 300mm Depth Framework Shall Be Made Up Of 25mm Ms Square Pipe As Per Drawing Two Drawers Each Of Width 150mm Shall Be Provided Drawer Shall Be Run On Telescopic Channel Of Appropriate Size Handle Shall Be Approved Shape Stainless Steel Of Size 100mm Long Top Of Teapoy And All Side Upper Sidebottombackfront Of Drawer Shall Be 18 Mm Thick Bwr Plywood Pasted With Laminated Sneet Of 09mm Thick Of Approved Shade On Outer Side And White On Inner Side Make Of Laminated Sheet Centurymarinogreenlam All Steel And Iron Surfaces Shall Be Epoxy Polyster Powder Coating Black And Thickness Not Less Than 45 Microns Rest All As Per Drawing Drg No Gekfur042025 And Specified And Approved By User Held In Ge Khadkwasla, Wooden Cockpit Platform For Super Dimona Simulator Of Size 3680 Mm X 2450 Mmx760 Mm Shall Be Made Up Of Comm Bwp Plywood Is 710 Frame Work Shall Be Done With 50 Mm Thick 2 X 25mm Bwp Ply Joint With Adhesive And Ss Screw Bwp Comm Ply For Load Bearing Capacity Of 1000 Kg As Per Drawing Attached And Specification Frame Work Shall Be Done With Five Horizontal Side Of Size 2450 Mm X 760 Mm X 50 Mm Joint With Four Vertical Side Of Size 3680 Mm X 760 Mm X 50 Mm At The Edge Ie Below The Top Ss Strip Of Size 50mm X 3mm Shall Be Provided In All Vertical And Horizontal Frame Top Of Platform Shall Be Of Size 3680 Mm X 2450 Mm Of 25 Mm Thick Bwp Plywood Is 710 Two Openings Shall Be Provided On Inner Side Of Front Compartment For Easy Access To Switch Point Maintenance Carpet Of Approved Shade Of Thickness 34mm Shall Be Provided On Top Of Plate Form And Stair Stair Of Size 840 Mm X 900 Mm X600 Mm High Of Three Steps As Per Drg Made Up Of 25mm Thick Bwp Plywood Shall Be Provided 1 Mm Thick Laminated Sheet Shall Be Pasted On All Four Wall Side Of Plate Form And Stair Rest All As Per Drg All Items Shall Be Required To Be Assemble At Site, Table With Cpu Hanger Of Size 1650 Mm X 900 Mm X 728 Mm, Chair Revolving Executive High Back, Bench Three Seater, Sofa Set 1 Seater Overall Size Width80cm Depth 82cm Height 85cm Seating Height 44 Cm Primary Material Pinewood Finish Colour Burgundy Upholstery Material Leatherette All As Per Manufacturer Catalogue And Specifications, Chair Visitor With Handle Abs Back Cover Shall Be Provided All As Per Manufactured Specifications As Follo Seat 4700 Cm W X480 Cm L Back 465 Cm W X605 Cm H Seat Height 465 Cm Chair Height 935 Cm Width Depth Of Chair As Measured From Pedestal Shall Be Widht 610 Cm Depth 645 Cm Seat Assembly The Seat Assembly Should Be Made Up Of 1201 Cm Thick Hot Pressed Plywood Upholstered With Fabric Upholstery Covers And Moulded Polyurethane Foam Back Assembly Should Made Up Of Powder Coated Tubular Frame The Back Should Be Upholsted Using Double Layer Spacer Nesh Fabric With High Tenacity Yarn Armrest One Peice Armrests Should Be Injectionmoulded From Black Copolymer Polypropylene Tubular Frame The Powder Coated Tubular Frame Should Be Cantilever Type, Plastic Bath Stool, Mattress Foam 78x36x4 Inch, Desk For Cadets Overall Size Shall Be 1270x820x540mm Steel Frame Work Shall Be Of 32 X 32 Mm Ms Square Tube Of Wall Thickness 16mm Top Shall Be Made Of 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side 06 Mm Thick Wooden Beading Shall Be Provided All Around The Top Sides Of The Desk Shall Be Covered With 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side Front Of The Desk Shall Be Covered With 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side With A Partition Made Of 32 X 32 Mm Ms Square Tube Of 16 Mm Thickness A Suitable Elevation Shall Be Provided On The Front Side Of The Desk All Wooden Surface Shall Be French Polished And All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coated Black And Thickness Not Less Than 45 Microns Shapesizespecifications And Finish Shall Be As Per Sample Drg Nogekfur082024 As Approved By User Held In Ge Khadakwasla Drg And Specifications Attached As Appendix Note Final Supply Of All Furniture Items Shall Only Be Carried Out After The Sample Approval Of Furniture By The Consignee, Bench For Cadets Overall Size Shall Be 1220x410x870mm Steel Frame Work Shall Be Of 32 X 32 Mm Ms Square Tube Of Wall Thickness 15mm Seat Size Of Seat Shall Be 1220x410x18 Mm And Back Size Of Back Shall Be 1220x150x18 Mm Shall Be Made Of 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Both Side 6 Mm Thick Wooden Beading Shall Be Provided All Around A Storage Space Made Of 15 X 15 Mm Ms Square Tubes Of Wall Thickness 16mm Shall Be Provided Below The Bench All Wooden Surface Shall Be French Polished And All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coated Black And Thickness Not Less Than 45 Microns Shapesizespecifications And Finish Shall Be As Per Sample Drg Nogekfur092024 As Approved By User Held In Ge Khadakwasia Drg And Specifications Attached As Appendix Note Final Supply Of All Furniture Items Shall Only Be Carried Out After The Sample Approval Of Furniture By The Consignee, Book Shelf For Cadets Size 1980 Mm H X 450 Mm L X 550 D Over All Dimension Of Book Shelf For Cadets Shall Be 1980 Mm High X 450 Mm Wide X 550 Mm Depth Frame Work Shall Be Made Up Of 25 Mm Ms Square Pipe As Por Drg Two Drawers Each Of Height 200 Mm Shall Be Provided At The Bottom Of Book Shelf Drawer Shalt Be Run On Telescopic Channal Of Appropriate Size Handle Shall Be Of Approved Shapestainless Steel Of Size 100 Mm Long All Three Sidef Except Front Side Of Each Compartment Shall Be Covered Upto 250 Mm Height With 10 Mm Thick Bwr Ply Pasted With 09 Mm Approved Mica On Both Side Edges Where Seen In Each Compartment Beading Shall Be Made Up Of Same Mica To Match With The Body All Sides Frontbackbottom Of Each Drawers Shall Be 18 Mm Thick Bwr Plywood Pasted With Laminated Sheet Of 09mm Thick Of Approved Shade On Front Side And Pasted With 00 Mm Thick White Shade On Inner Side Edges Where Seen Beading Shall Made Up Of Same Mica Shall Be Pasted To Match The Body All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coating Black And Thickness Not Less Than 50 Microns Rest All As Per Drg Gekfur032023 Approved By User And Sample Held At Ge Khadakwasla Drawing And Specifications Attached As Appendix, Shoe Rack For Cadet Mm H X 350 Mm D Size 850 Mm L X 625 Over All Dimension Of Shoe Rack Cadet Shall Be 850 Mm Length X 625 Mm High X 350 Mm Depth Frame Work Shall Be Made Up Of 25 Mm Ms Square Pipe As Per Drg Handle Shall Be Of Approved Shape Stainless Steel Of Size 100 Mm Long All Sides Incl Frontbackshelfsidetop Of Shoe Rack Shall Be Made Up Of 18 Mm Thick Bwr Ply Pasted With 09 Mm Mica Of Approved Shade On Front Side And Inner Side Both Door Shall Be Hang On 75 Mm Ssl Hinges Two Magnetic Catcher Shall Be Provided At The Botton Shelves Edges Where Seen Beading Shall Made Up Of Same Mica Shall Be Pasted To Match The Body All Steel And Iron Surfaces Shall Be Epoxy Polyester Powder Coating Black And Thickness Not Less Than 50 Microns Rest All As Per Drg Gekfur022023 Approved By User And Sample Held At Ge Khadakwasla Drawing And Specifications Attached As Appendix are available inside the detailed notification files. Bidders planning to target this contract in Pune should check the official portal schedule early to complete their online technical and financial submission well before the closing hours.